Peugeot 307 Break Dag 2004.5 Service Manual

34
30-08-2004
35
30-08-2004
YOUR 307 IN DETAILRADIO
Notes on radio reception
Your car radio is subject to pheno-
mena which do not affect domestic
radio sets. Both AM (MW/LW) and
FM reception are subject to various
forms of interference. This is no re-
lection on the quality of the equip-
ment, but is due to the nature of the
signals and the way in which they are
transmitted.
On MW/LW, interference may be
noticed when passing under high
voltage power lines or bridges, or in
tunnels.
On FM, interference may be the result
of increasing distance from the trans-
mitter, delection of the signals by
obstacles (mountains, hills, buildings,
etc.), or of being in an area which is
not covered by a transmitter. Selecting radio mode
Selecting a waveband
Adjusting the front/rear sound
distribution (Fader)
When
"FAD" is displayed, press but-
ton I or J.
Button I increases the volume in the
front.
Button J increases the volume in the
rear.
Adjusting the right/left sound
distribution (Balance)
When "BAL" is displayed, press but-
ton I or J.
Button I increases the volume on the
right-hand side.
Button J increases the volume on the
left-hand side.
Automatic volume correction
This function enables the volume to
be automatically adjusted depending
on the level of noise produced by the
speed of the vehicle.
Press buttons I or J to switch the
function on or off. Audio RB3:
press the
"SRC" button several
times in succession.
Audio RD3: press
button R.
Audio RB3: briely
press the "BND/AST"
button to select the
FM1, FM2, FMast and
AM wavebands.
Audio RD3: briely
press button R to
select the FM1, FM2,
FMast and AM wave-
bands.

36
30-08-2004
37
30-08-2004
YOUR 307 IN DETAIL
Manual station search
Press the "MAN" button.
Briely press button L or N to increase
or decrease the frequency displayed.
By continuing to press the button in
the direction selected, you will obtain
continuous scrolling of the frequency.
The scrolling stops as soon as the
button is released.
Pressing the "MAN" button again re-
turns you to automatic station search. Automatic storing of FM stations
in the memory (autostore)
Your radio automatically stores the
6 stations with the strongest signal in
FM
. These stations are stored in the
FMast waveband.
If it is not possible to ind 6 stations,
the remaining memories are empty.
Automatic station search
Manual storing of stations in the
memory
Select the station required.
Press one of the buttons "1" to "6"
for more than two seconds.
The sound stops then becomes audi-
ble again, conirming that the station
has been stored in the memory. Audio RB3:
press
and hold the "BND/
AST" button for more
than two seconds.
Audio RD3: press
and hold button R for
more than two sec-
onds.
Recalling stations stored in the
memory
For each waveband, briely press
buttons "1" to "6" to recall the cor-
responding station.
Briely press button
L or N to search
for the station immediately above or
below. By continuing to press the
button in the direction selected, you
will obtain continuous scrolling of the
frequency.
The scrolling stops at the irst sta-
tion found as soon as the button is
released.
If the TA trafic program is selected,
only stations broadcasting this type
of program are selected.
Searching for a station occurs irst
in "LO" sensitivity (selection of the
most powerful transmitters) during
scanning of the waveband, then in
"DX" sensitivity (selection of the
weakest and most distant transmit-
ters).
To make a direct search in "DX" sen-
sitivity, press button L or N twice.

36
30-08-2004
37
30-08-2004
YOUR 307 IN DETAIL
RDS
Using the RDS (Radio Data
System) function on FM
Radio Data System allows you to
continue listening to the same sta-
tion, whatever frequency it is using
for the region you are going through. Trafic information program Regional following mode
When they are part of a network,
certain stations broadcast regional
programs in the various areas they
serve. With regional following mode
you can keep listening to the same
program.
Press the "RDS" button for more
than two seconds to switch the func-
tion on or off.
RDS station following
The display indicates the name of the
station selected. The radio is contin-
ually searching for the station which
has the best reception and which is
transmitting the same program. Press the
"TA" button
to switch the function
on or off.
The multi-function dis-
play will show:
- "TA" if the function is selected,
- "(TA)" if the function is selected but
not available.
Any trafic information lash will be
given priority, whatever source you
are listening to (radio, cassette or
CD changer).
If you wish to interrupt a message,
press the "TA" button; this switches
the function off.
Note: the volume of trafic infor-
mation announcements is inde-
pendent of the volume of normal
radio listening. You can adjust
it using the volume button. The
setting will be stored and will be
used when the next messages are
broadcast.
Briely press the
"RDS"
button to switch the
function on or off.
The multi-function display will show:
- "RDS" if the function is selected.
- "(RDS)" if the function is selected
but not available.

38
30-08-2004
39
30-08-2004
YOUR 307 IN DETAIL
EON system: Audio RD3
This connects stations which are part
of the same network. It enables the
broadcast of trafic information or a
PTY program, by a station that is part
of the same network as the station to
which you are listening.
This service is available when you
have selected the TA trafic informa-
tion program or the PTY function.
PTY function:
Audio RD3
This allows you to listen to stations
broadcasting a speciic type of pro-
gram (news, culture, sport, rock etc.). To search for a
PTY program:
With FM selected,
press the "TA" but-
ton for two seconds to
switch this function on
or off. - select the
PTY function,
- briely press button L or N to scroll
down the list of the various types of
programs offered,
- when the program of your choice is displayed, keep button L or N
pressed for two seconds to carry
out an automatic search (after an
automatic search the PTY function
is switched off).
In PTY mode the different types of
programs can be stored in the mem-
ory. To do this, press the preselection
buttons "1" to "6" for two seconds.
Briely press the corresponding but-
ton to recall the type of program
stored in the memory.

40
30-08-2004
41
30-08-2004
YOUR 307 IN DETAIL
Ejection of a discSelecting a track Shufle (RDM)
When the CD player is selected, press
and hold button Q for two seconds.
The tracks will be played in random
sequence. Pressing the button again
for two seconds returns you to normal
play.
Shufle mode is de-activated each time
the set is switched off.
After insertion of a disc,
printed face upwards,
the player starts auto-
matically.
If a disc is already in-
serted, press button Q.
COMPACT DISC: AUDIO RD3
Selecting CD mode
Press button L to select the next
track.
Press button N to return to the start
of the current track or to select the
previous track.
The use of copied compact
discs may cause faults.Insert circular compact
discs only.
Press button
S to
eject the disc from the
player. Accelerated play
Press and hold button
L or N for for-
wards or backwards accelerated play.
Accelerated play stops as soon as
the button is released.

43
30-08-2004
GPS AUDIO/TELEPHONE RT3
YOUR 307 IN DETAIL
Stalk movementFunction
1 - Press (behind) Increase volume
2 - Press (behind) Decrease volume
1 + 2 - Press together Switch off sound (mute); restore sound by pressing an y button
3 - Press Automatic search of upper frequencies (radio) - Selection of next tra
ck (CD/CD changer)
Continuous pressure until release: accelerated forwards play (CD/C D changer)
4 - Press Automatic search of lower frequencies (radio) - Selection of previous
track (CD/CD changer)
Continuous pressure until release: accelerated backwards play (CD/C D changer)
5 - Press end Change source (radio/CD/CD changer) - Conirmation of selection (o
n a menu or screen) -
Call connect/Call disconnect (Tel./incoming call) - Call disconn ect (Tel./Engaged)
Press for more than 2 seconds: display contextual menu (Tel./Not en gaged)
6 - Rotation
(clockwise) Selection of higher station stored in memory or sto
ring in memory in position 1 for station not in
memory (radio) - Selection of following CD - Select ion of following item, on a menu or screen
7 - Rotation
(anti-clockwise) Selection of lower station stored in memory or stor
ing in memory in position 6 for station not in
memory (radio) - Selection of previous CD - Selecti on of previous item, on a menu or screen

44
30-08-2004
45
30-08-2004
YOUR 307 IN DETAIL
ButtonFunction
A Press: audio/telephone on/off.
Rotation: volume adjustment.
B 5
Ejection of CD.
C SOURCE Selection of source: radio, CD, CD changer or Aux.
D Call connect (Tel/Incoming call) - Display contextual menu (Tel/N ot engaged).
E Access "PEUGEOT" services menu.
Press for between 2 and 8 seconds: call "PEUGEOT Assistance" direct.
Press for more than 8 seconds: cancellation of the call made.
F MODE Change display.
Press for more than 2 seconds: display general information.
G Press: display contextual menu of display - Conirm inputting or ad
justment.
Rotation: move within a menu - Select function/parameter -
Audio settings: sound ambience, bass, treble, loudness, fader (f ront/rear balance),
balance (left/right balance), automatic volume.
H 5Adjust higher frequency, step by step or continuous (long press).
Select previous CD (CD changer) - Movement on map (navigation).
I 6Adjust lower frequency, step by step or continuous (long press).
Select following CD (CD changer) - Movement on map (navigation).
J Infra-red window (IrDA)*.
K ESC Cancel current operation.
Press for more than 2 seconds: clear all superimposed displays and retu
rn to permanent
application.
L SIM card cover.
M 8Automatic search of higher frequency - Selection of following CD
track.
Movement on map (navigation).
Double press: change from LO mode to DX mode.
Press for more than 2 seconds: CD accelerated forwards play.

44
30-08-2004
45
30-08-2004
YOUR 307 IN DETAIL
* During the year.
ButtonFunction
N 7Automatic search of lower frequency - Selection of previous CD track.
Movement on map (navigation).
Double press: change from LO mode to DX mode.
Press for more than 2 seconds: CD accelerated backwards play.
O DARK
1st press: display top band (remainder of screen is black) - 2nd press: brightness removed (black scre en) -3rd press: return to normal screen.
Press for more than 10 seconds: reinitialisation of the system.
P MENU Display general menu -
Press for more than 2 seconds: display help screen and list of voice
commands.
Q Disconnect.
Press for more than 2 seconds: activation/deactivation of the tran
sfer of the call to the voice mail
or to a call diversion number.
R BAND
AST Select FM1, FM2, FMast, AM wavebands.
Press for more than 2 seconds: automatic storing of stations (autosto
re).
S TA/PTY Trafic information priority on/off.
Press for more than 2 seconds: PTY function on/off.
T RDS RDS function on/off.
Press for more than 2 seconds: regional following mode on/off.
U AUDIO Display window for adjusting sound ambience, bass, treble, lo
udness, sound distribution and
automatic correction of volume.
V SOS Press between 2 and 8 seconds: emergency call.
Press for more than 8 seconds: cancellation of the call made.
1 to 6 1 2 3 4 5 6 Select station in memory.
Press more than 2 seconds: store station being listened to in memo
ry.
1 to 5 1 2 3 4 5 Selection of CDs in the CD changer.
0 to 9 * # 0 1 2 3 4 5
6 7 8 9 * # Alphanumeric keypad for entering text and telephone numbers.

46
30-08-2004
47
30-08-2004
YOUR 307 IN DETAIL
GENERAL FUNCTIONSAnti-theft system
The RT3 GPS audio/telephone is
coded in such a way that it can op-
erate only on your vehicle. If itting
it to another vehicle, consult your
PEUGEOT dealer for coniguration
of the system.
The anti-theft system is automatic
and requires no action on your
part.
On/off
With the ignition switch
in the accessories po-
sition or with the igni-
tion on, press button
A
to switch the audio
function of the RT3
GPS audio/telephone
on or off.
Note:
in the absence of an ignition
key, press button A to switch the
telematics system on or off.
The RT3 GPS audio/telephone can
operate for 30 minutes without
switching the vehicle ignition on.
Notes:
- the SIM card must be removed only after the audio/telephone has been
switched off,
- following automatic switching off of the audio/telephone after
30 minutes it is possible to make a
telephone call by pressing button D,
- after the ignition has been switched off, the audio/telephone can be
switched on again by pressing but-
tons D, E , V or by inserting a CD in
the player.
AUDIO SETTINGS
ADJUSTING THE VOLUME
Turn button A clockwise to increase
the volume of the audio/telephone or
anti-clockwise to decrease it.
Note: the volume setting is speciic
to each source. It is possible to have
different settings for radio, CD or CD
changer. Press button
U to ac-
cess the Sound Ambi-
ence , Bass , Treble ,
Loudness , Fader (front/
rear balance), Balance
(left/right balance) and Automatic volume adjustment setting
windows.
Exit from audio mode is automatic af-
ter a few seconds without any action,
or by pressing the "ESC" button.
Note: bass, treble and loudness set-
tings are speciic to each source. It is
possible to have different settings for
radio, CD or CD changer.

46
30-08-2004
47
30-08-2004
YOUR 307 IN DETAIL
Treble setting
When "Treble" is displayed, turn
button G to vary the setting.
- "-9" for minimum treble setting
- "0" for normal setting
- "+9" for maximum treble setting
Sound ambience
This function permits
the selection of a
"None", "Rock", "Clas-
sical", "Jazz", "Vocal"
or "Techno" sound
ambience.
Turn button G to select
the sound ambience.
Selecting "None" permits access
to all of the settings deined below.
Selecting another ambience sets the
bass and treble automatically.
Bass setting
When "Bass" is displayed, turn but-
ton G to vary the setting.
- "-9" for minimum bass setting
- "0" for normal setting
- "+9" for maximum bass setting Setting the right/left sound
distribution (Balance)
When
"Balance" is displayed:
- Turn button G clockwise to increase
the volume on the right.
- Turn button G anti-clockwise to in-
crease the volume on the left.
Automatic volume adjustment
This function allows the volume to
be adjusted automatically depending
on the level of noise produced by the
speed of the vehicle.
Press button G to switch the function
on or off.
Adjusting the loudness
This function automatically empha-
sises bass and treble tones when the
volume is low.
Rotate button
G to switch the func-
tion on or off.
Setting the front/rear sound
distribution (Fader)
When "Fader" is displayed:
- Turn button G clockwise to increase
the volume in the front.
- Turn button G anti-clockwise to in-
crease the volume in the rear.