PEUGEOT 307 BREAK DAG 2004 Owner's Manual

20
30-08-2004
21
30-08-2004
INSTRUMENTS AND
CONTROLS
A permanently lit warning light or
one that lashes with the engine
running, indicates an operating
fault in the relevant unit. Some
warning lights may be linked to
buzzers and a message on the multi-
function display. Do not ignore
this warning: contact a PEUGEOT
dealer as soon as possible.
If the Central STOP warning light
comes on when you are driving,
stop immediately where it is safe
to do so.Central STOP warning
light
This light comes on each time the
ignition is switched on.
It is linked to the "engine oil pres-
sure", ''coolant level low'', ''brake
luid level'', "electronic brake force
distribution fault" warning lights and
the coolant temperature gauge.
Stop immediately if it lashes with
the engine running.
Contact a PEUGEOT dealer.
Engine oil pressure
warning light
Linked to the central STOP warning
light.
If it comes on with the engine run-
ning, it is accompanied by an au-
dible signal and the message
''Oil
pressure insuficient'' on the multi-
function display.
Stop immediately.
If there is a lack of oil in the lubrica-
tion circuit, top up the level.
Contact a PEUGEOT dealer without
delay.
Diesel engine low coolant
level warning light
Linked to the central STOP warning
light.
This comes on for approximately
3 seconds each time the ignition is
switched on.
This warning light is accompanied by
an audible signal and the message
"Top up engine coolant level" on
the multi-function display.
Stop immediately.
Warning:
Allow the engine to cool
before topping up.
The cooling system is pressurised.
Handbrake and low brake
luid level warning light
Linked to the central STOP warning
light.
This comes on each time the ignition
is switched on.
Illumination of this light is accompa-
nied by an audible signal and a mes-
sage on the multi-function display
indicating the cause of the warning:
- ''Handbrake on'' , if the handbrake
is applied or has not been released
correctly,
-
''Brake luid level low'' if there is
an excessive drop in the brake luid
(if the light remains on even with
the handbrake released),
- ''Braking fault'' is displayed si-
multaneously with the ABS light,
indicating a malfunction of the elec-
tronic brake force distribution.
Stop immediately.
Contact a PEUGEOT dealer.
To prevent the risk of scalding, un-
screw the cap by two turns to allow
the pressure to drop.
Once the pressure has dropped, re-
move the cap and top up the level.
Contact a PEUGEOT dealer.
INSTRUMENTS AND CONTROLS

20
30-08-2004
21
30-08-2004
Battery charge warning
light
This comes on each time the ignition
is switched on.
If it comes on with the engine run-
ning, it is accompanied by an audi-
ble signal and a message
"Battery
charge fault" on the multi-function
display.
It can indicate:
- faulty operation of the charging circuit,
- loose battery or starter terminals,
- a cut or slack alternator belt,
- an alternator fault.
Contact a PEUGEOT dealer.
Anti-lock braking system
(ABS) warning light
This light comes on for 3 seconds
each time the ignition is switched
on.
If it remains on or comes on above
8 mph (12 kmh), this indicates a mal-
function of the ABS.
However, the vehicle retains conven-
tional servo-assisted braking.
Illumination of this light is accom-
panied by an audible signal and the
message
''ABS fault'' on the multi-
function display.
Contact a PEUGEOT dealer.
Electronic stability
program (ESP/ASR)
warning light
This comes on for 3 seconds each
time the ignition is switched on.
If the light remains on or comes on
when the engine is running and the
vehicle is moving, it is accompa-
nied by an audible signal and the
message
''ESP/ASR system not
functioning'' on the multi-function
display; contact a PEUGEOT dealer.
When the engine is running and the
vehicle is moving, it lashes if the
system is activated.
It is lit continuously when the system
is disarmed. To regenerate the ilter, you are ad-
vised to drive, as soon as possible
when trafic conditions permit, at a
speed of 35 mph (60 km/h) or above
for at least ive minutes (until the
warning light goes out). If the warning
light remains on, contact a PEUGEOT
dealer.
Note:
following prolonged operation
of the vehicle at very low speed or at
idle, you may, in exceptional circum-
stances, notice emissions of water
vapour at the exhaust on accelera-
tion. This does not have any effect
on the vehicle's performance or on
the environment.
If it lashes when the engine is run-
ning, accompanied by an audible
signal and the message
''Catalytic
converter fault'' on the multi-func-
tion display, it indicates a malfunction
in the injection or ignition system.
There is a risk of damage to the cata-
lytic converter (petrol engines only).
Contact a PEUGEOT dealer as soon
as possible.
Engine diagnostics
warning light
This comes on each time the ignition
is switched on.
If it comes on with the engine run-
ning, accompanied by an audible
signal and the message on the multi-
function display:
-
''Antipollution fault'', it indicates a
malfunction in the emission control
system.
-
''Unblock diesel ilter'' indicates
the start of saturation of the par-
ticulate emission ilter (due to ex-
ceptionally prolonged urban driving
conditions: reduced speed, long
trafic jams, ...).
INSTRUMENTS AND CONTROLS

22
30-08-2004
23
30-08-2004
Diesel pre-heat light
This comes on each time the ignition
is switched on.
Wait until it goes out before trying the
starter.
Water in diesel ilter
warning light (according
to country)
Illumination of this warning light is ac-
companied by an audible signal and
the message
''Water in diesel fuel
ilter'' on the multi-function display.
There is a risk of damage to the
injection system.
Contact a PEUGEOT dealer a soon
as possible.
Passenger air bag
disarmed indicator light
Illumination of this warning light is
accompanied by a message "Pas-
senger air bag deactivated" on the
multi-function display.
If the passager air bag is disarmed,
the indicator light comes on when the
ignition is switched on and remains
on.
In all cases, if the warning light lash-
es, contact a PEUGEOT dealer.
Air bag warning light
This light comes on for a few seconds
when the ignition is switched on.
Illumination of this warning light, with
the engine running, is accompanied
by an audible signal and the mes-
sage
"Air bag fault" on the multi-
function display indicating:
- a fault in the front air bags,
or
- a fault in the side air bags or curtain air bags.
Contact a PEUGEOT dealer.
Seat belt not fastened
warning light
With the engine running, this indica-
tor light comes on when the driver's
seat belt is not fastened.
Low fuel level warning
light
The warning light comes on for
three seconds when the ignition is
switched on.
When this light comes on with the
engine running, it is accompanied by
an audible signal and the message
"Fuel level low" on the multi-func-
tion display.
When the warning light comes on,
you have enough fuel to drive approx-
imately
30 miles (50 km). The tank
capacity is approximately 60 litres.
This light lashes to indicate a mal-
function of the fuel gauge. The in-
dicator's needle moves to the rest
position (below the zero).
Contact a PEUGEOT dealer.
INSTRUMENTS AND CONTROLS

24
30-08-2004
25
30-08-2004
INSTRUMENTS AND CONTROLS
INSTRUMENT
PANEL DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset (see correspond-
ing section). It is determined by two
parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
Example: 4,800 miles/km remain
before the next service.
For ive seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) re-
main before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit.
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.

24
30-08-2004
25
30-08-2004
INSTRUMENTS AND CONTROLS
The service is overdue.
The service spanner lashes for
5 seconds after the ignition is
switched on.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 10 seconds, after the
service information.
Lack of oil Oil level gauge fault
The level read on the dipstick
will only be correct if the vehicle
is on level ground and the en-
gine has been off for more than
15 minutes.
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service. Check the oil level using the dipstick.
If the level is correct, the lashing in-
dicates an actual malfunction of the
engine oil level gauge.
Contact a PEUGEOT dealer.
Flashing indicates a lack of oil which
could damage the engine.
If the lack of oil is conirmed by a
check using the dipstick, it is essen-
tial that the level is topped up.

27
30-08-2004
YOUR 307 IN DETAIL
Monochrome screen B
This enables the following informa-
tion to be displayed:
- the time,
- the date,
- the outside temperature (it lashes when there is a risk of ice),
- the radio displays,
- the status of the openings (doors, bonnet...),
- the warning messages (e.g. "Bat- tery charge fault") or information
messages (e.g. "Passenger air bag
deactivated") displayed temporarily
can be cleared by pressing button
1 or 2,
- the trip computer (see correspond- ing section).
MULTI-FUNCTION SCREENS
PresentationMonochrome screen CT and
colour screen DT
These two systems are controlled
by the RT3 GPS audio/telephone
keypad.
They enable the following informa-
tion to be displayed:
- the time,
- the date,
- the outside temperature (a mes- sage warns you when there is a
risk of ice),
- the audio source displays (radio, CD, ...),
- the telematic system displays (tele- phone, services, ...),
- the status of the openings (doors, bonnet, ...),
- the warning messages (e.g. "Fuel level low") and vehicle functions
status messages (e.g. "Passenger
air bag deactivated") displayed
temporarily,
- the trip computer display (see cor- responding section),
- the satellite navigation system dis- plays (see corresponding section).
Note: to enable you to use all of
your system's functions, you have
two CD ROMs: one, "Coniguration",
contains the software and the vari-
ous display and spoken information
languages, the other, "Navigation",
contains the satellite navigation sys-
tem map data. Press the RT3 audio/telephone
"MENU"
button to access the general
menu and select one of the following
applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 Audio/ telephone" section),
- trip computer (see corresponding section),
- directory (see "RT3 audio/ telephone" section),
- telematics (see "RT3 audio/ telephone" section),
- coniguration (see corresponding section).
Monochrome screen CT
General menu

28
30-08-2004
29
30-08-2004
YOUR 307 IN DETAIL
Press the RT3 audio/telephone
"MENU" button to access the general
menu and select one of the following
applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 audio/ telephone" section),
- trip computer (see corresponding section),
- directory (see "RT3 audio/telephone" section),
Colour screen DT
General menu
-
telematics (see "RT3 audio/telephone"
section),
- coniguration (see corresponding
section),
- map (see section "Satellite naviga- tion system"),
- video (see corresponding section).
Monochrome screen B
Press button 1 for two seconds to
gain access to the settings .
Then, each press of this button permits
scrolling of the various parameters.
-
language of the information displayed,- unit of speed (km or miles),
- unit of temperature (degrees Celsius or Fahrenheit),
- time format (12 or 24 hours),
- hour,
- minute,
- year,
- month,
- day.
Pressing button 2 enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After seven seconds without action,
the screen returns to the usual dis-
play, the modiied data are recorded.
Parameter coniguration
A few deinitions
Superimposed display
a window appears over the current
application for a short while, to an-
nounce a change of status of another
application.
Permanent application
main application currently in use, dis-
played in the main screen window.
Contextual menu
limited menu associated with the
main application currently in use, dis-
played in the main screen window.

28
30-08-2004
29
30-08-2004
YOUR 307 IN DETAIL
Press the RT3 audio/telephone
"MENU" button to access the general
menu and select one of the following
applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 audio/ telephone" section),
- trip computer (see corresponding section),
- directory (see "RT3 audio/telephone" section),
Colour screen DT
General menu
-
telematics (see "RT3 audio/telephone"
section),
- coniguration (see corresponding
section),
- map (see section "Satellite naviga- tion system"),
- video (see corresponding section).
Monochrome screen B
Press button 1 for two seconds to
gain access to the settings .
Then, each press of this button permits
scrolling of the various parameters.
-
language of the information displayed,- unit of speed (km or miles),
- unit of temperature (degrees Celsius or Fahrenheit),
- time format (12 or 24 hours),
- hour,
- minute,
- year,
- month,
- day.
Pressing button 2 enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After seven seconds without action,
the screen returns to the usual dis-
play, the modiied data are recorded.
Parameter coniguration
A few deinitions
Superimposed display
a window appears over the current
application for a short while, to an-
nounce a change of status of another
application.
Permanent application
main application currently in use, dis-
played in the main screen window.
Contextual menu
limited menu associated with the
main application currently in use, dis-
played in the main screen window.

28
30-08-2004
29
30-08-2004
YOUR 307 IN DETAIL
CT monochrome screen
The "Coniguration" menu gives
access to the following para-meters:
• "Adjust the brightness": display brightness setting,
• "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter: insert the coniguration
CD-Rom); setting of the spoken
commands,
• "International parameters": date and time setting (12 or 24 hour
mode, adjustment of the minutes
on GPS); units setting (l/100 - °C or
mpg - °F),
• "Choice of language": selection of the language for the display, infor-
mation and voice commands (Ger-
man, English, Spanish, French,
Italian, Dutch, Portuguese: insert
the coniguration CD-Rom). DT colour screen
The
"Display Coniguration" menu
gives access to the following
parameters:
• "Choose colours": selection from the palette of colours available for
display,
• "Luminosity and brightness": dis- play brightness setting,
• "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter: insert the coniguration
CD-Rom); setting of the spoken
commands,
• "International parameters": date and time setting (12 or 24 hour
mode, adjustment of the minutes
on GPS); units setting (l/100 - °C or
mpg - °F),
• "Choice of language": selection of the language for the display, infor-
mation and voice commands (Ger-
man, English, Spanish, French,
Italian, Dutch, Portuguese: insert
the coniguration CD-Rom). Video on the DT screen
It is possible to connect video equip-
ment (a camcorder, digital camera, ...)
using the three video sockets situated
inside the glove box.
For safety reasons, con-
iguration of the multi-
function screens by the
driver must be carried out
when stationary.
It is only possible to display
video images when the vehicle is
stationary.
Select the "Video" menu from the
main menu :
- "Activate video mode" to activate/ cancel the video function,
- "Video parameters" to adjust the display format, the brightness, con-
trast and colour.
Press "MODE" or "DARK" to exit
video mode.
Successive presses on the "SOURCE"
button allow you to select another audio
source other than the video.

30
30-08-2004
31
30-08-2004
AUDIO RB3YOUR 307 IN DETAIL
Stalk movement
Function
1 - Press (behind) Increase volume.
2 - Press (behind) Decrease volume.
1 + 2 - Simultaneous press Sound cut-off (mute); restoring of the sound b y pressing any button.
3 - Press Automatic search of higher frequencies (radio) -
Selection of the next track (CD).
4 - Press Automatic search of lower frequencies (radio) -
Selection of the previous track (CD).
5 - Press the end Change of source (radio/cassette/CD changer).
6 - Rotation
(clockwise) Selection of next station stored in the memory (radio) -
Selection of next CD.
7 - Rotation
(anti-clockwise) Selection of previous station stored in the memory (radio) -
Selection of previous CD.