Peugeot 307 Break Dag 2005.5 Workshop Manual

Comfort48 -
01-10-2005
49Comfort-
01-10-2005
6. Demisting the rear screen and the mirrors
Pressing the button once
demists the rear screen
and the exterior mirrors.
This switches off automatically
to prevent an excessive
consumption of current.
Pressing again reactivates demisting.
It is possible to stop demisting before
it is switched off automatically by
pressing the button again. In certain cases of particu-
larly arduous use (towing
the maximum load on a
steep gradient in high tem-
peratures), switching off the
air conditioning permits the recovery
of engine power and therefore an in-
crease in the towing capacity.
In order for the air conditioning to be
fully effective, the windows must be
closed.
The air conditioning system does not
contain chlorine and does not present
any danger to the ozone layer.
Operate the air conditioning system
for 5 to 10 minutes, once or twice a
month, to keep it in perfect working
order.
The water produced by the air con-
ditioning condensation is discharged
through an opening provided for this
purpose. Therefore, a puddle of wa-
ter may form underneath the vehicle
when stationary.
In order to ensure that the air con-
ditioning system operates correctly,
regular checks are also recom-
mended.
If the system does not produce
cold air, do not use it and contact a
PEUGEOT dealer.
5. Air intake/Air recirculation
Pressing button 5 permits
recirculation of the interior
air. This is indicated by
illumination of the indicator
light.
As soon as possible, press button 5
again to permit the intake of outside
air, to prevent deterioration of the air
quality and to avoid misting of the
windows. This is indicated by the
switching off of the indicator light.
The interior air recirculation enables you
to isolate the passenger compartment
from exterior odours and smoke.
The outside air intake enables you to
prevent and eliminate misting of the
windscreen and side windows.
Used simultaneously with the air
conditioning, air recirculation enables
performance to be improved.
Used in a humid climate, air recirculation
may result in misting of the windows.
Rapid demisting of the
windscreen
To quickly de-ice or demist the
windscreen and side windows:
- place the air distribution control in the "windscreen and side windows"
position,
- place the temperature 2 and air
low 3 controls at maximum, as
indicated by the "Windscreen
and side windows" symbol on the
control panel,
- close the centre vents,
- switch air intake button 5 to the
"Outside Air Intake" position (button
5 indicator light off),
- start the air conditioning by pressing button 1.

Comfort50 -
01-10-2005
51Comfort-
01-10-2005
DUAL ZONE AUTOMATIC AIR
CONDITIONING
The air conditioning only operates
when the engine is running.When the engine is cold, to prevent
too great a distribution of cold air, the
air low will reach its optimum level
gradually.
The driver and his front
passenger can each adjust
the temperature to their
requirements.
The value indicated on the
display corresponds to a level of
comfort and not to a temperature in
degrees Celsius or Fahrenheit.
Turn control 1 or 2 to the left or to
the right respectively to decrease or
increase this value.
A setting around the value 21
provides optimum comfort. However,
depending on your requirements, a
setting between 18 and 24 is normal. For optimum comfort, you are advised
to avoid a left/right setting difference
of more than 3.
For maximum cooling or heating of the
passenger compartment, it is possible
to go below the value 15 by turning until
"LO"
is displayed or above the value
27 by turning until "HI" is displayed.
4. Automatic visibility programme
The automatic comfort
programme may not be
suficient to quickly demist
or de-ice the windscreen
and side windows (humidity,
several passengers, ice, etc.).
In this case, select the automatic
visibility programme.
The system automatically controls
the air conditioning, the air low and
the air intake and provides optimum
distribution of the ventilation to the
windscreen and side windows.
To switch it off, press button 4 again
or press the "AUTO" button, the
button's indicator light switches off
and "AUTO" is displayed.
Automatic operation
1. Automatic comfort
programme
Press the "AUTO" button.
The "AUTO" symbol is
displayed.
We recommend the use
of this mode: it permits
automatic and optimised adjustment
of all of the functions, passenger
compartment temperature, air low,
air distribution and air recirculation,
in accordance with the comfort value
that you have chosen. This system is
designed to operate effectively in all
seasons, with the windows closed. 2. Driver's side adjustment
3. Passenger side adjustment
On entering the vehicle,
if the interior temperature
is much colder or warmer
than the comfort value,
there is no need to change
the value displayed in order to obtain
the comfort required. The system
corrects the difference in temperature
automatically and as quickly as
possible.

Comfort50 -
01-10-2005
51Comfort-
01-10-2005
Manual operation
If you wish, you can make a different
choice from that offered by the
system by changing a setting. The
other functions will still be controlled
automatically. Pressing the "AUTO"
button returns the system to
completely automatic operation.
Press this button to stop air
cooling.
Automatic operation of
the air conditioning is
resumed when the button
is pressed again. The symbol " A/C"
is displayed.
Avoid prolonged use of this mode (risk
of condensation, odour, humidity).
Press this button again as soon as
possible.
6. Air distribution adjustment
Pressing this button several
times in succession enables
the air low to be directed in
turn towards:
- the windscreen and side windows (de-icing or demisting),
- the windscreen, the side windows and the footwells,
- the footwells,
- the centre vents, the side vents and the footwells,
- the centre and side vents. 7. Air low adjustment
Press the
"small fan" or "large fan"
button respectively to decrease or
increase the low of air.
The air low symbol, the fan, ills
progressively in relation to the value
required.
8. Air intake/Air recirculation 9. Demisting the rear screen and
the mirrors
Press this button for
recirculation of the interior
air. The air recirculation
symbol 8 is displayed.
Air recirculation enables the
passenger compartment to be isolated
from exterior odours and smoke.
Avoid prolonged recirculation of
interior air (risk of condensation and
deterioration of the air quality).
As soon as possible, press this button
again to permit the intake of outside
air and prevent condensation.
5. Air conditioning On/Off
Press this button to demist
the rear screen and the
exterior mirrors. The button
9
indicator light comes on.
Demisting switches off
automatically to prevent an excessive
consumption of current. It is possible
to stop operation of the demisting
before it is switched off automatically
by pressing the button again.
10. Switching the system off
Press the "small fan" button of
the air low 7 until the fan symbol
disappears.
This action switches off all of the
functions of the air conditioning
system, with the exception of the
demisting of the rear screen 9.
Temperature related comfort is no
longer guaranteed but a slight low
of air, due to the movement of the
vehicle, can still be felt.
Pressing the "large fan" button of
the air low 7 again or the AUTO
button reactivates the system with
the values set before it was switched
off.

Comfort52 -
01-10-2005
53Comfort-
01-10-2005
MIRRORS
Electric exterior mirrors
Adjustment
F Slide switch A to the right or to the
left to select the corresponding
mirror.
F Move knob B in all four directions
to adjust.
F Return switch A to the centre po-
sition. Folding
- from inside:
F
with the ignition on, pull switch A
rearwards.
- from outside:
F lock the vehicle using the remote
control or the key.
Note: if the mirrors are folded using
switch A, they will not unfold when
the vehicle is unlocked using the
remote control or the key. Switch A
must be pulled again.
Unfolding
- from inside:
F with the ignition on, pull switch A
rearwards.
- from outside:
F unlock the vehicle using the re-
mote control or the key.
The folding and unfolding of
the exterior mirrors can be
deactivated by a PEUGEOT
dealer.
In certain cases of
particularly arduous use
(towing the maximum load
on a steep gradient in high
temperatures), switching
off the air conditioning permits
the recovery of engine power and
therefore an increase in the towing
capacity.
In order for the air conditioning to be
fully effective, the windows must be
closed.
The air conditioning system does not
contain chlorine and does not present
any danger to the ozone layer.
Operate the air conditioning for 5 to
10 minutes, once or twice a month, to
keep it in good working order.
The water produced by the air con-
ditioning condensation is discharged
through an opening provided for this
purpose. Therefore, a puddle of water
may form underneath the vehicle
when stationary.
In order to ensure that the air
conditioning system operates
correctly, regular checks are also
recommended.
If the system does not produce
cold air, do not use it and contact a
PEUGEOT dealer.

Comfort52 -
01-10-2005
53Comfort-
01-10-2005
Manual exterior mirrors
Move the lever in all four directions
to adjust.
When the vehicle is parked, the
exterior mirrors can be folded back
manually.The exterior mirror on the
driver's side is convex (out-
er edge deined by a dotted
line) in order to eliminate
the "blind spot".
As a result, objects observed in the
driver's and passenger's mirrors are
in reality closer than they appear.
This must be taken into account to
correctly judge the distance of vehi-
cles approaching from behind.
Automatic day/night interior
mirror
This automatically and gradually
changes between the day and night
positions. To prevent dazzling, the
glass of the mirror darkens auto-
matically depending on the intensity
of the light from behind. It clears as
the light (headlamps of following ve-
hicles, sunlight) decreases, ensuring
maximum visibility.
Manual interior mirror
The interior mirror has two positions:
- day (normal),
- night (anti-dazzle).
To change from one to the other,
push or pull the lever on the lower
edge of the mirror.
Operation
Switch on the ignition and press
switch 1:
- Indicator light 2 lit (switch pressed):
automatic operation.
- Indicator light 2 off: automatic sys-
tem off. The mirror remains at its
most clear.
Special feature
To ensure maximum visibility dur-
ing manoeuvres, the mirror clears
automatically when reverse gear is
engaged.
STEERING WHEEL HEIGHT
AND DEPTH ADJUSTMENT
When the vehicle is stationary, un-
lock the steering wheel by pulling
handle A.
Adjust the height and depth of the
steering wheel.
Lock it by pushing handle A down
fully.

Comfort52 -
01-10-2005
53Comfort-
01-10-2005
Manual exterior mirrors
Move the lever in all four directions
to adjust.
When the vehicle is parked, the
exterior mirrors can be folded back
manually.The exterior mirror on the
driver's side is convex (out-
er edge deined by a dotted
line) in order to eliminate
the "blind spot".
As a result, objects observed in the
driver's and passenger's mirrors are
in reality closer than they appear.
This must be taken into account to
correctly judge the distance of vehi-
cles approaching from behind.
Automatic day/night interior
mirror
This automatically and gradually
changes between the day and night
positions. To prevent dazzling, the
glass of the mirror darkens auto-
matically depending on the intensity
of the light from behind. It clears as
the light (headlamps of following ve-
hicles, sunlight) decreases, ensuring
maximum visibility.
Manual interior mirror
The interior mirror has two positions:
- day (normal),
- night (anti-dazzle).
To change from one to the other,
push or pull the lever on the lower
edge of the mirror.
Operation
Switch on the ignition and press
switch 1:
- Indicator light 2 lit (switch pressed):
automatic operation.
- Indicator light 2 off: automatic sys-
tem off. The mirror remains at its
most clear.
Special feature
To ensure maximum visibility dur-
ing manoeuvres, the mirror clears
automatically when reverse gear is
engaged.
STEERING WHEEL HEIGHT
AND DEPTH ADJUSTMENT
When the vehicle is stationary, un-
lock the steering wheel by pulling
handle A.
Adjust the height and depth of the
steering wheel.
Lock it by pushing handle A down
fully.

Comfort54 -
01-10-2005
55Comfort-
01-10-2005
FRONT SEATS
1. Forwards-backwards adjustment
Lift the control and slide the seat for-
wards or backwards.
2. Driver's or passenger's seat height adjustment
Pull the handle upwards or push it
downwards as many times as neces-
sary to obtain the required position.
3. Seat back angle adjustment
Push the handle towards the rear.
4. Access to rear seats (3 door)
Pull the handle to fold the seat back
and move the seat forwards. On
repositioning, the seat returns to its
initial position.
Note: it is also possible to use con-
trol 3. Then adjust the angle.
No person or object must
prevent the seat slide from
returning to its initial posi-
tion; return to this position
is necessary for the seat to
lock in place.

Comfort54 -
01-10-2005
55Comfort-
01-10-2005
5. Head restraint height and angle adjustment
To raise the head restraint, pull it
upwards.
To remove the head restraint, press
the lug A and pull the head restraint
upwards.
To put the head restraint back in po-
sition, locate the stems of the head
restraint in the holes, taking care to
keep them in line with the seat back.
To lower the head restraint, press the
lug A and the head restraint at the
same time.
The head restraint has a frame with
a notch which prevents the head re-
straint from lowering; this is a safety
device which provides protection in
the event of an impact.
To tilt the head restraint, tilt the lower
part forwards or rearwards. 8. Heated seats switch

Never drive with the head
restraints removed; they
must be in place and cor-
rectly adjusted.
REAR HEAD RESTRAINTS
These have a high position for when
they are in use and a low position for
when they are stored.
The head restraints can also be re-
moved.
To remove them, pull upwards as far
as the stop then press the lug.
6. Armrests
These can be folded down and are
removable.
To remove them, press the button
located between the armrest and the
side of the seat and pull it.
7. Storage drawers
There is a storage drawer under
each front seat.
- To open it, lift it and pull.
- To take it out, open it to its full extent,
press the ends of the slides and lift it,
then remove it completely.
- To put it back in place, with it fully closed, press on the top of the
drawer to secure it.
Under the front passenger seat, the
layout of the loor allows for storage
of a irst aid kit and a warning triangle
(small version).
The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head.
Do not place heavy objects
in the drawers. With the engine running, press the
switch. The temperature is controlled
automatically.
Pressing the switch again stops
operation.
Note:
the command for activation
of heating of the seat(s) remains
memorised for two minutes after the
ignition has been switched off.

Comfort56 -
01-10-2005
57Comfort-
01-10-2005
REAR SEATS (SALOON)
To fold down the rear left seat (2/3 part)
or the right seat (1/3 part), always start
with the seat, never with the seat
back (risk of damage) :
- move the front seat(s) forward if necessary,
- lift the front of the seat cushion 1,
- tilt the seat cushion 1 against the
front seat(s),
- check that the seat belt is correctly positioned on the side of the seat
back,
- pull control 2 forwards to unlock the
seat back 3,
- place the head restraints in the low position,
- fold down the seat back 3.
Note: the seat cushion 1 can be re-
moved to increase the volume of the
load space.
Squeeze the seat cushion ixings to
detach them from their fastenings. When repositioning:
- fold up the seat back and lock it
(the red marker of control 2 should
no longer be visible),
- fold up the seat.
Take care not to trap the seat belts
and to position the stalks cor-
rectly.

Comfort56 -
01-10-2005
57Comfort-
01-10-2005
Removing the seat cushion
(position against the front
seats):
Take hold of the seat cushion 1 at the
bottom to remove it from its ixings
and pull upwards.
- pull control 2 forwards to release
the seat back 3,
- place the head restraints in the low position,
- tilt the seat back 3.
Note: the seat cushion 1 can be re-
moved to increase the volume of the
load space.
REAR SEATS (ESTATE)
Folding the seats:
To fold the rear left seat (2/3 section)
or the rear right seat (1/3 section), al-
ways start with the seat cushion,
never with the seat back (risk of
damage) :
- move the front seat(s) forward if necessary,
- pull the handle A located between
the seat cushion 1 and the seat
back 3 forwards, then pull it up-
wards to lift the seat cushion and
tilt it against the front seat(s),
- check that the seat belt is posi- tioned correctly on the side of the
seat back,
Refitting the seat
cushion (position against
the front seats):
- it the seat cushion 1 in its ixings,
- to lock it, press on the top of the seat cushion 1.
Putting the seats back in
position:
- fold the seat back and lock it (the
red indicator on control 2 should no
longer be visible),
- fold the seat cushion.
Take care not to trap the seat belts
and to position the stalks cor-
rectly.