Peugeot 307 Break Dag 2005 Manual Online

74 -
01-06-2005
75
-
01-06-2005
Automatic switching on of the
lights
Side lights and dipped beam head-
lamps switch on automatically if the
light is poor, or during operation of
the windscreen wipers. They switch
off as soon as the light becomes
bright enough or the windscreen wip-
ers stop.
Note:
in foggy weather or in snow,
the brightness sensor can detect suf-
icient light. As a consequence, the
lights will not come on automatically. Deactivation
The deactivation of this function is
accompanied by a message on the
multifunction display.
The function is deactivated tempo-
rarily when you use the manual lights
stalk.
Manual "Follow-me-home" lighting
When the automatic switching
on of the lights function is deac-
tivated,
the side lights and dipped
headlamps remain on for the dura-
tion selected for the automatic "fol-
low-me-home" lighting.
If the vehicle is not itted with the
automatic switching on of the lights
function, when you leave your vehicle,
the side lights and dipped headlamps
remain on for thirty seconds.
Direction indicators (lashers)
Left: downwards.
Right: upwards.
Note : if you forget to cancel the di-
rection indicator, the volume of the
audible signal will increase, if you
are driving at a speed greater than
50 mph (80 km/h).
Automatic "Follow me home"
lighting
With the ignition off, when you leave
your vehicle with the automatic
switching on of the lights func-
tion activated , the side lights and
dipped headlamps remain on for the
selected duration. Activation:
F
switch off the engine,
F "lash" the headlamps,
F get out of the vehicle and lock it.
Deactivation:
F "lash" the headlamps again,
F get out of the vehicle and lock it.
To deactivate or activate
this function, go to the mul-
tifunction display conigura-
tion menu.
The duration of the timed period must
also be set (15, 30, 60 seconds), via
the multifunction display conigura-
tion menu, except in the case of the
monochrome screen A for which it
is pre-set.
Cancelling:
F "lash" the headlamps,
F get out of the vehicle and lock it. To switch the function on
or off, use the multifunction
display coniguration menu.
Activation
The activation of this function is ac-
companied by a message on the
multifunction display.
The function is activated when the
manual lights stalk is in position 0.
If the brightness sensor does not
function correctly, the lights come
on accompanied by the service warn-
ing light, an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness
sensor, coupled with the
rain sensor, located in the
centre of the windscreen,
behind the interior mirror.
It is used for the automatic switching
on of the lights.
Visibility

74 -
01-06-2005
75
-
01-06-2005
Automatic switching on of the
lights
Side lights and dipped beam head-
lamps switch on automatically if the
light is poor, or during operation of
the windscreen wipers. They switch
off as soon as the light becomes
bright enough or the windscreen wip-
ers stop.
Note:
in foggy weather or in snow,
the brightness sensor can detect suf-
icient light. As a consequence, the
lights will not come on automatically. Deactivation
The deactivation of this function is
accompanied by a message on the
multifunction display.
The function is deactivated tempo-
rarily when you use the manual lights
stalk.
Manual "Follow-me-home" lighting
When the automatic switching
on of the lights function is deac-
tivated,
the side lights and dipped
headlamps remain on for the dura-
tion selected for the automatic "fol-
low-me-home" lighting.
If the vehicle is not itted with the
automatic switching on of the lights
function, when you leave your vehicle,
the side lights and dipped headlamps
remain on for thirty seconds.
Direction indicators (lashers)
Left: downwards.
Right: upwards.
Note : if you forget to cancel the di-
rection indicator, the volume of the
audible signal will increase, if you
are driving at a speed greater than
50 mph (80 km/h).
Automatic "Follow me home"
lighting
With the ignition off, when you leave
your vehicle with the automatic
switching on of the lights func-
tion activated , the side lights and
dipped headlamps remain on for the
selected duration. Activation:
F
switch off the engine,
F "lash" the headlamps,
F get out of the vehicle and lock it.
Deactivation:
F "lash" the headlamps again,
F get out of the vehicle and lock it.
To deactivate or activate
this function, go to the mul-
tifunction display conigura-
tion menu.
The duration of the timed period must
also be set (15, 30, 60 seconds), via
the multifunction display conigura-
tion menu, except in the case of the
monochrome screen A for which it
is pre-set.
Cancelling:
F "lash" the headlamps,
F get out of the vehicle and lock it. To switch the function on
or off, use the multifunction
display coniguration menu.
Activation
The activation of this function is ac-
companied by a message on the
multifunction display.
The function is activated when the
manual lights stalk is in position 0.
If the brightness sensor does not
function correctly, the lights come
on accompanied by the service warn-
ing light, an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer.
Do not cover the brightness
sensor, coupled with the
rain sensor, located in the
centre of the windscreen,
behind the interior mirror.
It is used for the automatic switching
on of the lights.
Visibility

76 -
01-06-2005
77
-
01-06-2005
MANUAL ADJUSTMENT OF
THE HEADLAMPS
For vehicles itted with halogen
bulbs, depending on the load in your
vehicle, adjusting the beam of your
headlamps is recommended.
0 -
1 or 2 people in the front seats.
- - 3 people.
1 - 5 people.
2 - 5 people + maximum authorised
loads.
3 - Driver + maximum authorised
loads.
Initial setting is position 0.
AUTOMATIC HEADLAMP
ADJUSTMENT
On vehicles with xenon bulbs:
when stationary, the system au-
tomatically corrects the height of
the beam, whatever the load of the
vehicle. The driver is then assured
of having optimum lighting and not
causing a nuisance to other road
users.
In cases of malfunction,
the service warning light
comes on on the instru-
ment panel, accompanied
by an audible signal and
a message on the multifunction dis-
play. The system places your head-
lamps to the low position.
Do not touch the xenon bulbs. Con-
tact a PEUGEOTdealer.
Visibility

76 -
01-06-2005
77
-
01-06-2005
Special position of the front
windscreen wiper
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
the windscreen.
This action enables you to position
the wiper blades for winter parking,
cleaning or replacement (See sec-
tion "Practical information - Chang-
ing a wiper blade").
To park the wipers after this has been
done, switch on the ignition and op-
erate the stalk.
Windscreen and headlamp wash
Pull the windscreen wiper stalk to-
wards you. The windscreen wash
then the windscreen wipers operate
for a ixed period.
The headlamp wash is also activat-
ed,
if the headlamps are on .
WINDSCREEN WIPER STALK
Front windscreen wiper with
automatic wipe
2 Fast wipe (heavy rain).
1 Normal wipe
(moderate rain).
I Intermittent wipe.
0 Off.
AUTO â Automatic or single wipe
(press downwards).
In the Intermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In AUTO mode, the wiping speed is
in proportion to the intensity of the
rainfall. The irst press of the stalk
downwards activates the automatic
wipe.
Subsequent presses trigger a single
wipe.
Front windscreen wiper with
intermittent wipe
2
Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
l Intermittent wipe.
0 Off.
â Single wipe (press downwards).
In the Intermittent position, the wiping
speed is in proportion to the vehicle
speed.
Visibility

78 -
01-06-2005
79
-
01-06-2005
Automatic windscreen wipers
In
AUTO mode, the windscreen wip-
ers operate automatically and adapt
their speed to the intensity of the
rainfall . Do not cover the rain sen-
sor located on the wind-
screen behind the interior
mirror.
When using an automatic
car wash, switch off the ignition.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
Activation
Activation of the function is accom-
panied by a message on the multi-
function display.
The automatic windscreen wipers
function must be reactivated if the
ignition has been switched off for
more than one minute, by pressing
the stalk downwards.
Rear windscreen wiper
To activate or deactivate
this function, go to the multi-
function display conigura-
tion menu.
If there is a signiicant accumulation
of snow or ice and when using a bi-
cycle carrier on the tailgate (estate),
deactivate the automatic rear wiper
by going to the multifunction display
coniguration menu.
Rear windscreen wash
Deactivation
Deactivation of the function is ac-
companied by a message on the
multi-function display.
The function is deactivated when the
windscreen wipers stalk is moved to
position
I, 1 or 2.
In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in
intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Turn ring A past the irst
notch; the windscreen wash
then the windscreen wiper
operate for a ixed period.
Turn ring
A to the irst notch
for intermittent wiping.
When reverse gear is en-
gaged, if the windscreen
wipers are in operation, the
rear wiper starts.
Visibility

78 -
01-06-2005
79
-
01-06-2005
Automatic windscreen wipers
In
AUTO mode, the windscreen wip-
ers operate automatically and adapt
their speed to the intensity of the
rainfall . Do not cover the rain sen-
sor located on the wind-
screen behind the interior
mirror.
When using an automatic
car wash, switch off the ignition.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
Activation
Activation of the function is accom-
panied by a message on the multi-
function display.
The automatic windscreen wipers
function must be reactivated if the
ignition has been switched off for
more than one minute, by pressing
the stalk downwards.
Rear windscreen wiper
To activate or deactivate
this function, go to the multi-
function display conigura-
tion menu.
If there is a signiicant accumulation
of snow or ice and when using a bi-
cycle carrier on the tailgate (estate),
deactivate the automatic rear wiper
by going to the multifunction display
coniguration menu.
Rear windscreen wash
Deactivation
Deactivation of the function is ac-
companied by a message on the
multi-function display.
The function is deactivated when the
windscreen wipers stalk is moved to
position
I, 1 or 2.
In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in
intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
Turn ring A past the irst
notch; the windscreen wash
then the windscreen wiper
operate for a ixed period.
Turn ring
A to the irst notch
for intermittent wiping.
When reverse gear is en-
gaged, if the windscreen
wipers are in operation, the
rear wiper starts.
Visibility

78 -
01-06-2005
79
-
01-06-2005
COURTESY LIGHTS
1. Front courtesy light
2. Map reading lights

With the ignition on, press the
corresponding switch.
3. Rear courtesy light
4. Rear reading lights (estate)
With the ignition on, press the
corresponding switch. The front and rear courtesy lights
come on automatically when the ig-
nition key is removed, on unlocking
the vehicle or on opening one of the
doors.
They gradually go off:
-
after the ignition has been switched on,- with the ignition off, 30 seconds
after the last door is closed,
- when the vehicle is locked. Deactivation
The courtesy lights can be deactivat-
ed by pressing switch
1 for more than
three seconds. Pressing switch 1 or
3 briely switches the corresponding
courtesy light on and off.
The map reading lights are not af-
fected by this and may always be
switched on.
Saloon:
Pressing switch 1 switches on the
front and rear courtesy lights for ten
minutes.
Pressing switch 3 switches on the
rear courtesy light.
Estate:
Pressing switch 1 or 3 switches on
the corresponding courtesy light for
ten minutes.
Pressing switch 4 switches on the
reading light concerned. Reactivation
To re-activate the automatic lighting,
press switch
1 again.
Visibility

82 -
01-06-2005
83
-
01-06-2005
Layout

82 -
01-06-2005
83
-
01-06-2005
INTERIOR LAYOUT
1. Glove box with cooling facility 2. Front ashtray
Pull the lid to open the ashtray.
To empty it after opening, press the
tab and remove the ashtray.
3. Storage
4. 12 volt socket
This is a lighter type socket, itted
with a cap. It is supplied with current
from the running position.
5. Door tray
6. Storage/Can holder
7. Coin storage
8. Waste container
To empty this, open it fully (past the
point of resistance) then pull on the
receptacle to remove it.
To reit, lock it in place on the cover.
This is itted with a lock.
To open the glove box, lift the handle.
The glove box lights when the lid is
opened.
It has a ventilation nozzle that can
be closed
A, distributing the same
cooled air as the vents of the pas-
senger compartment
It contains three sockets* B for con-
necting video equipment.
The layout allows storage of a water
bottle, a pen, the vehicle handbook,
a pair of spectacles, tokens, etc.
FITTING/REMOVING THE MAT
When itting the mat for the irst time,
use only the ixings supplied in the
wallet attached.
When removing the mat on the
driver's side:
- push the seat as far back as pos- sible,
- unscrew the ixings fully,
- remove the ixings, then the mat.
When reitting, position the mat
correctly and replace the ixings by
pressing them in.
* With DT colour screen only.
Layout

82 -
01-06-2005
83
-
01-06-2005
INTERIOR LAYOUT
1. Glove box with cooling facility 2. Front ashtray
Pull the lid to open the ashtray.
To empty it after opening, press the
tab and remove the ashtray.
3. Storage
4. 12 volt socket
This is a lighter type socket, itted
with a cap. It is supplied with current
from the running position.
5. Door tray
6. Storage/Can holder
7. Coin storage
8. Waste container
To empty this, open it fully (past the
point of resistance) then pull on the
receptacle to remove it.
To reit, lock it in place on the cover.
This is itted with a lock.
To open the glove box, lift the handle.
The glove box lights when the lid is
opened.
It has a ventilation nozzle that can
be closed
A, distributing the same
cooled air as the vents of the pas-
senger compartment
It contains three sockets* B for con-
necting video equipment.
The layout allows storage of a water
bottle, a pen, the vehicle handbook,
a pair of spectacles, tokens, etc.
FITTING/REMOVING THE MAT
When itting the mat for the irst time,
use only the ixings supplied in the
wallet attached.
When removing the mat on the
driver's side:
- push the seat as far back as pos- sible,
- unscrew the ixings fully,
- remove the ixings, then the mat.
When reitting, position the mat
correctly and replace the ixings by
pressing them in.
* With DT colour screen only.
Layout