Peugeot 307 CC 2005.5 Owner's Guide

Instruments and controls24 -
01-10-2005
25Instruments and controls-
01-10-2005
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows
"=0" , re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The service spanner lashes for
5 seconds after the ignition is
switched on.
Example:
the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must
be carried out soon. The display
indicates the total and trip distance.
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.

Instruments and controls24 -
01-10-2005
25Instruments and controls-
01-10-2005
Lighting rheostat
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or
reduce) the brightness.
As soon as the lighting is of the
required brightness, release the
button.
Trip recorder zero reset
button
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you
to alternate between the distance
recorder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
a few seconds, after the service
information.
Oil level correct
Oil level gauge fault
Flashing of "OIL --" indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
Flashing of "OIL",
linked with the ser-
vice warning light,
accompanied by
an audible signal
and a message on
the multifunction display, indicates a
lack of oil which could damage the
engine.
If the lack of oil is conirmed by
a check using the dipstick, it is
essential that the level is topped up.
Lack of oil Dipstick
There are 2 marks on the
dipstick:- never exceed level A,
- in position B, top up the level via the oil iller cap,
using the type of oil suited
to your engine.
A = max.
B = min.

Instruments and controls22 -
01-10-2005
23Instruments and controls-
01-10-2005
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on
locking and unlocking the vehicle.
It also displays the information
relating to the cruise control or
speed limiter, when either of these
is activated (see corresponding
section).
Service indicator
This indicates when the next service
is due in accordance with the
manufacturer's servicing schedule.
The point at which the next
service is due is calculated from
the last indicator zero reset (see
corresponding section). It is
determined by two parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted
by the time factor, depending on the
user's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symboli-
sing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.
Example: 4,800 miles/km remain
before the next service. For ive
seconds after the ignition is switched
on, the display indicates:
In the event of under-revving or over-
revving, the gear selected lashes for
a few seconds, then the actual gear
engaged is displayed.
This comes on when
the automatic gearbox
"SPORT" operating pro-
gramme is selected.
This comes on when
the automatic gearbox
"SNOW” operating pro-
gramme is selected.
Automatic gearbox indicator
lights
"SNOW" indicator light Invalid value during
manual operation
This is displayed if a gear
is not engaged correctly
(selector between two
positions).
"SPORT" indicator light

Instruments and controls22 -
01-10-2005
23Instruments and controls-
01-10-2005
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on
locking and unlocking the vehicle.
It also displays the information
relating to the cruise control or
speed limiter, when either of these
is activated (see corresponding
section).
Service indicator
This indicates when the next service
is due in accordance with the
manufacturer's servicing schedule.
The point at which the next
service is due is calculated from
the last indicator zero reset (see
corresponding section). It is
determined by two parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted
by the time factor, depending on the
user's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symboli-
sing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.
Example: 4,800 miles/km remain
before the next service. For ive
seconds after the ignition is switched
on, the display indicates:
In the event of under-revving or over-
revving, the gear selected lashes for
a few seconds, then the actual gear
engaged is displayed.
This comes on when
the automatic gearbox
"SPORT" operating pro-
gramme is selected.
This comes on when
the automatic gearbox
"SNOW” operating pro-
gramme is selected.
Automatic gearbox indicator
lights
"SNOW" indicator light Invalid value during
manual operation
This is displayed if a gear
is not engaged correctly
(selector between two
positions).
"SPORT" indicator light

Instruments and controls24 -
01-10-2005
25Instruments and controls-
01-10-2005
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows
"=0" , re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The service spanner lashes for
5 seconds after the ignition is
switched on.
Example:
the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must
be carried out soon. The display
indicates the total and trip distance.
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.

Instruments and controls24 -
01-10-2005
25Instruments and controls-
01-10-2005
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows
"=0" , re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The service spanner lashes for
5 seconds after the ignition is
switched on.
Example:
the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must
be carried out soon. The display
indicates the total and trip distance.
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.

Instruments and controls24 -
01-10-2005
25Instruments and controls-
01-10-2005
Lighting rheostat
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or
reduce) the brightness.
As soon as the lighting is of the
required brightness, release the
button.
Trip recorder zero reset
button
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you
to alternate between the distance
recorder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
a few seconds, after the service
information.
Oil level correct
Oil level gauge fault
Flashing of "OIL --" indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
Flashing of "OIL",
linked with the ser-
vice warning light,
accompanied by
an audible signal
and a message on
the multifunction display, indicates a
lack of oil which could damage the
engine.
If the lack of oil is conirmed by
a check using the dipstick, it is
essential that the level is topped up.
Lack of oil Dipstick
There are 2 marks on the
dipstick:- never exceed level A,
- in position B, top up the level via the oil iller cap,
using the type of oil suited
to your engine.
A = max.
B = min.

Instruments and controls26 -
01-10-2005
27Instruments and controls-
01-10-2005
TRIP COMPUTER
Each time the button on the end of the
wiper stalk is pressed, the various
items of trip computer data are
displayed in succession, depending
on the multifunction display.
Monochrome screen CT
- the "vehicle" tab with:
• the range, the current consump- tion
and the distance still to be
driven,
- tab "1" (route 1) with:
• the average speed, the average consumption and the distance
driven calculated over route
"1"
- tab "2" (route 2) with the same
features for a second route.
Zero re-set
When the required route is displayed,
press the button for more than two
seconds.
Monochrome screens C
- the "vehicle" tab with:
• the range, the current consump- tion and the distance still to be
driven,
- tab "1" (route 1) with:
• the average speed, the average consumption and the distance
driven calculated over route
"1" ,
- tab "2" (route 2) with the same
features for a second route.
Zero re-set
When the required route is displayed,
press the button for more than two
seconds.

Instruments and controls26 -
01-10-2005
27Instruments and controls-
01-10-2005
Colour screen DT
- the "Current information" with:
• the range,
• the current consumption,
• the distance still to be driven.
- "Route 1" with:
• the distance travelled,
• the average consumption,
• the average speed,
- "Route 2" with the same features
for a second route.
Zero re-set
When the required route is displayed,
press the button for more than two
seconds. This igure may increase if there
is a change in the style of driving
or the road surface, producing
a signiicant drop in current
consumption.
When the range is less than 20 miles
(30 km), dashes are displayed. After
illing with at least 5 litres of fuel,
the range is recalculated and is
displayed when it exceeds 62 miles
(100 km).
If dashes are displayed for long
periods instead of digits, contact a
PEUGEOT dealer.
Current consumption
This is the average quantity of
fuel consumed during the last few
seconds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
It can be displayed in litres/100,
km/litre or mpg (refer to on-board
computer coniguration).
Average consumption
This is the average fuel consumption
since the computer was last set to
zero.
It can be displayed in litres/100,
km/litre or mpg (refer to on-board
computer coniguration).
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
The routes
"1" and ''2'' are indepen-
dent but have identical application.
Route "1" for example allows you
to make daily calculations and route
"2" monthly calculations.
Distance remaining to be
travelled
This is the distance remaining to
the inal destination. It can either
be calculated continuously by the
navigation system if guidance is
activated, or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The routes
Range
This shows the distance that can still
be covered with the fuel remaining
in the tank in accordance with the
average consumption over the last
few miles (kilometres) driven.

Instruments and controls28 -
01-10-2005
Access via the general menu
Screen C
Screen CT
Screen DT"On-board computer" menu
Press the
"MENU" button to access
the general menu.
Select the icon ''On-board
computer'' , then validate to access
its menu.
Depending on the multifunction
display, this menu offers various
choices:
- Enter distance to destination,
- Warning log.
- Status of the functions.
or
- On-board computer coniguration.
- Diagnostics,
- Status of the functions.
Enter distance to destination
If guidance has not been activated,
this enables you to enter an
approximate distance to inal
destination value, to permit all of the
on-board computer calculations.
Warning log
This summarises the active warning
messages, displaying them in suc-
cession on the multifunction display. Status of the functions
This summarises the active or not
active status of the functions present
on the vehicle.
On-board computer coniguration
This function allows the distance
to the destination to be input
(when guidance is not activated;
otherwise this information is given
by the navigation system) and also
changing of the units of measurement
(°C or °F, km and litres or miles and
gallons).
The consumption values (current
or average) can be displayed in
litres/100, km/litre or mpg.
Diagnostics
This presents the information relating
to the warning log, as regards the
energy remaining in the back-up
battery and the number of satellites
which can be seen by the GPS
system.