Peugeot 307 CC 2006 Manual PDF

62
Closing the roof
 Carry out the preparatory opera-tions, indicated on the previous page.
 Then, press button 4 until the roof closing operation is complete, confirmed by an audible signal and a message on the multifunc-tion display.
When carrying out this manoeuvre, the four windows lower, the boot opens, the moving shelf and the roof unfold and position themselves, the hinged covers fold, then the boot closes.
If you continue to press but-ton 4 once the cycle is com-plete, the four windows rise again.
During roof opening and closing operations, to avoid any risk of injury, ensure that there is no-one in the prox-imity of the moving parts.
Operation of the roof is the sole responsibility of the driver.
Carry out one complete roof manoeu-vre at least once a month to keep it in perfect working order.
After rain or washing the vehicle, it is advisable to wait for the roof to dry before opening it.
To guarantee correct operation, do not release button 4 when the roof is in an intermediate position (neither completely open nor com-pletely closed).
However, in the event of danger, release the control knob and the operation will stop instantly. Once the danger has been eliminated, complete the operation.
The control buttons for the windows become operational again at the end of the roof operation.
In the case of an electric or hydraulic malfunction of the roof, switch off the ignition, restart the engine, then start the required operation again.
If the problem persists, it is possible to close the roof manually.
To do this, please consult the breakdown procedure described at the end of this handbook (roof emergency mode).

63
The engine must be switched offwhen filling with fuel.
 Open the fuel filler flap.
 Insert the key then turn it to the left.
 Remove the cap and hang it on the hook located on the inside of the flap.
A label affixed to the inside of the fuel filler flap indicates which type of fuel to use.
When you fill your tank, do not con-tinue after the third cut-off of the pump. This could cause your vehicle to malfunction.
The capacity of the tank is approx-imately 60 litres.
 After filling the tank, lock the cap and close the fuel filler flap.Low fuel level
When the minimum fuel level in the tank is reached, this warn-ing light comes on on the instrument panel.
You can still drive approximately 30 miles (50 km).
Operating fault
With the ignition on, if the fuel gauge needle remains in or returns to the rest positon (below zero), this indicates a malfunction of the fuel gauge.
Contact a PEUGEOT dealer.
FILLING WITH FUEL

64
Front and rear lights (Ring A)
Place ring A in the required position.
Dipped/Main beam change
Pull the stalk towards you.
Lights off
Side lights
Dipped / Main beam headlamps
Front fog lamps (1st for-wards turn of the ring)
The front fog lamps operate with the side lights and dipped headlamps.
Front fog lamps and rear fog lamp (2nd forwards turn of the ring)
Note: to switch off the rear fog lamp and the front fog lamps, turn the ring twice backwards.
Front fog lamps and rear fog lamp (ring B)
Turn ring B forwards to switch on and backwards to switch off. The status is confirmed by the light on the instru-ment panel.
Lights on buzzer
With the ignition off and the automatic switching on of the lights deactivated, when the driver's door is opened, a buzzer sounds to warn you that you have left your lights on.
In good or rainy weather, both day and night, the front fog lamps and the rear fog lamp are dazzling and are prohibited.
Do not forget to switch them off when they are no longer needed.
LIGHTS STALK
The rear fog lamp will be deactivated automatically when towing.

65
Automatic switching on of the lights
Side lights and dipped beam head-lamps switch on automatically if the light is poor, or during operation of the windscreen wipers. They switch off as soon as the light becomes bright enough or the windscreen wip-ers stop.
Note: in foggy weather or in snow, the brightness sensor can detect suf-ficient light. As a consequence, the lights will not come on automatically.
Deactivation
The deactivation of this function is accompanied by a message on the multifunction display.
The function is deactivated tempo-rarily when you use the manual lights stalk.
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a message on the multifunction dis-play.
Contact a PEUGEOT dealer.
Manual "Follow-me-home" lighting
When the automatic switching on of the lights function is deac-tivated, the side lights and dipped headlamps remain on for the dura-tion selected for the automatic "fol-low-me-home" lighting.
If the vehicle is not fitted with the automatic switching on of the lights function, when you leave your vehicle, the side lights and dipped headlamps remain on for thirty seconds.
Direction indicators (flashers)
Left: downwards.
Right: upwards.
Note: if you forget to cancel the direction indicator, the volume of the audible signal will increase, if you are driving at a speed greater than 50 mph (80 km/h).
Automatic "Follow-me-home" lighting
With the ignition off, when you leave your vehicle with the automatic switching on of the lights func-tion activated, the side lights and dipped headlamps remain on for the selected duration.
Activation:
 switch off the engine,
 "flash" the headlamps,
 get out of the vehicle and lock it.
Deactivation:
 "flash" the headlamps again,
 get out of the vehicle and lock it.
To deactivate or activate this function, go to the mul-tifunction display configura-tion menu.
The duration of the timed period must also be set (15, 30, 60 seconds), via the multifunction display configura-tion menu.
Cancelling:
 "flash" the headlamps,
 get out of the vehicle and lock it.
To switch the function on or off, use the multifunc-tion display configuration menu.
Activation
The activation of this function is accompanied by a message on the multifunction display.
The function is activated when the manual lights stalk is in position 0.
Do not cover the brightness sensor, coupled with the rain sensor, located in the centre of the windscreen, behind the interior mirror. It is used for the automatic switching on of the lights.

65
Automatic switching on of the lights
Side lights and dipped beam head-lamps switch on automatically if the light is poor, or during operation of the windscreen wipers. They switch off as soon as the light becomes bright enough or the windscreen wip-ers stop.
Note: in foggy weather or in snow, the brightness sensor can detect suf-ficient light. As a consequence, the lights will not come on automatically.
Deactivation
The deactivation of this function is accompanied by a message on the multifunction display.
The function is deactivated tempo-rarily when you use the manual lights stalk.
If the brightness sensor does not function correctly, the lights come on accompanied by the service warning light, an audible signal and a message on the multifunction dis-play.
Contact a PEUGEOT dealer.
Manual "Follow-me-home" lighting
When the automatic switching on of the lights function is deac-tivated, the side lights and dipped headlamps remain on for the dura-tion selected for the automatic "fol-low-me-home" lighting.
If the vehicle is not fitted with the automatic switching on of the lights function, when you leave your vehicle, the side lights and dipped headlamps remain on for thirty seconds.
Direction indicators (flashers)
Left: downwards.
Right: upwards.
Note: if you forget to cancel the direction indicator, the volume of the audible signal will increase, if you are driving at a speed greater than 50 mph (80 km/h).
Automatic "Follow-me-home" lighting
With the ignition off, when you leave your vehicle with the automatic switching on of the lights func-tion activated, the side lights and dipped headlamps remain on for the selected duration.
Activation:
 switch off the engine,
 "flash" the headlamps,
 get out of the vehicle and lock it.
Deactivation:
 "flash" the headlamps again,
 get out of the vehicle and lock it.
To deactivate or activate this function, go to the mul-tifunction display configura-tion menu.
The duration of the timed period must also be set (15, 30, 60 seconds), via the multifunction display configura-tion menu.
Cancelling:
 "flash" the headlamps,
 get out of the vehicle and lock it.
To switch the function on or off, use the multifunc-tion display configuration menu.
Activation
The activation of this function is accompanied by a message on the multifunction display.
The function is activated when the manual lights stalk is in position 0.
Do not cover the brightness sensor, coupled with the rain sensor, located in the centre of the windscreen, behind the interior mirror. It is used for the automatic switching on of the lights.

66
For vehicles fitted with halogen bulbs, depending on the load in your vehicle, adjusting the beam of your headlamps is recommended.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 4 people.
-. Intermediate setting.
2. 4 people + maximum authorised loads.
-. Intermediate setting.
3. Driver + maximum authorised loads.
Initial setting is position 0.
On vehicles with xenon bulbs:
when stationary,the system auto-matically corrects the height of the beam, whatever the load of the vehi-cle. The driver is then assured of hav-ing optimum lighting and not causing a nuisance to other road users.
In cases of malfunction, the service warning light comes on on the instrument panel, accompanied by an audible signal and a mes-sage on the multifunction display. The system places your headlamps to the low position.
Do not touch the xenon bulbs. Contact a PEUGEOT dealer.
Daytime lights*
On vehicles which are equipped with daytime lights, the dipped headlamps come on when the vehicle is started.
* According to country.
The instruments and controls (instrument panel, multifunc-tion display, air conditioning control panel,...) are only lit on switching to the automatic switch-ing on of the lights mode or when the lights are switched on manually.
This warning light comes on on the instrument panel.
MANUAL ADJUSTMENT OF
THE HEADLAMPSAUTOMATIC HEADLAMP
ADJUSTMENT

67
Special position of the front
windscreen wiper
In the minute following switching off of the ignition, any action on the stalk positions the wipers in the centre of the windscreen.
This action enables you to position the wiper blades for winter parking, cleaning or replacement (See section "Practical information - Changing a wiper blade").
To park the wipers after this has been done, switch on the ignition and oper-ate the stalk.
Windscreen and headlamp wash
Pull the windscreen wiper stalk towards you. The windscreen wash then the windscreen wipers operate for a fixed period.
The headlamp wash is also activated, if the headlamps are on.
2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
l Intermittent wipe.
0 Off.
 Single wipe (press downwards).
In the Intermittent position, the wip-ing speed is in proportion to the vehi-cle speed.
2 Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
I Intermittent wipe.
0 Off.
AUTO  Automatic or single wipe (press downwards).
In the Intermittent position, the wiping speed is in proportion to the speed of the vehicle.
In AUTO mode, the wiping speed is in proportion to the intensity of the rainfall. The first press of the stalk downwards activates the automatic wipe.
Subsequent presses trigger a single wipe.
WINDSCREEN WIPER STALK
Front windscreen wiper with intermittent wipe Front windscreen wiper with automatic wipe

68
Automatic windscreen wipers
In AUTO mode, the windscreen wip-ers operate automatically and adapt their speed to the intensity of the rainfall.
Do not cover the rain sensor located on the windscreen behind the interior mirror.
When using an automatic car wash, switch off the ignition.
In winter, it is advisable to wait for the windscreen to completely clear of ice before operating the automatic wipe.Activation
Activation of the function is accom-panied by a message on the multi-function display.
Deactivation
Deactivation of the function is accom-panied by a message on the multi-function display.
The function is deactivated when the windscreen wipers stalk is moved to position I, 1 or 2.
In the event of malfunction of the automatic windscreen wipers, the windscreen wipers will operate in intermittent mode.
Contact a PEUGEOT dealer to have the system checked.
In this position, the courtesy light comes on automati-cally:
- when the vehicle is unlocked,- when the key is removed from the ignition,- when a door is opened,- when the vehicle location function is used.
It switches off gradually:
- when the vehicle is locked,- when the ignition is switched on,- with the ignition off, 30 seconds after the last door is closed.
COURTESY LIGHTS
1. Front courtesy light
The automatic windscreen wipers function must be reactivated if the ignition has been switched off for more than one minute, by press-ing the stalk downwards.

68
Automatic windscreen wipers
In AUTO mode, the windscreen wip-ers operate automatically and adapt their speed to the intensity of the rainfall.
Do not cover the rain sensor located on the windscreen behind the interior mirror.
When using an automatic car wash, switch off the ignition.
In winter, it is advisable to wait for the windscreen to completely clear of ice before operating the automatic wipe.Activation
Activation of the function is accom-panied by a message on the multi-function display.
Deactivation
Deactivation of the function is accom-panied by a message on the multi-function display.
The function is deactivated when the windscreen wipers stalk is moved to position I, 1 or 2.
In the event of malfunction of the automatic windscreen wipers, the windscreen wipers will operate in intermittent mode.
Contact a PEUGEOT dealer to have the system checked.
In this position, the courtesy light comes on automati-cally:
- when the vehicle is unlocked,- when the key is removed from the ignition,- when a door is opened,- when the vehicle location function is used.
It switches off gradually:
- when the vehicle is locked,- when the ignition is switched on,- with the ignition off, 30 seconds after the last door is closed.
COURTESY LIGHTS
1. Front courtesy light
The automatic windscreen wipers function must be reactivated if the ignition has been switched off for more than one minute, by press-ing the stalk downwards.

68
Automatic windscreen wipers
In AUTO mode, the windscreen wip-ers operate automatically and adapt their speed to the intensity of the rainfall.
Do not cover the rain sensor located on the windscreen behind the interior mirror.
When using an automatic car wash, switch off the ignition.
In winter, it is advisable to wait for the windscreen to completely clear of ice before operating the automatic wipe.Activation
Activation of the function is accom-panied by a message on the multi-function display.
Deactivation
Deactivation of the function is accom-panied by a message on the multi-function display.
The function is deactivated when the windscreen wipers stalk is moved to position I, 1 or 2.
In the event of malfunction of the automatic windscreen wipers, the windscreen wipers will operate in intermittent mode.
Contact a PEUGEOT dealer to have the system checked.
In this position, the courtesy light comes on automati-cally:
- when the vehicle is unlocked,- when the key is removed from the ignition,- when a door is opened,- when the vehicle location function is used.
It switches off gradually:
- when the vehicle is locked,- when the ignition is switched on,- with the ignition off, 30 seconds after the last door is closed.
COURTESY LIGHTS
1. Front courtesy light
The automatic windscreen wipers function must be reactivated if the ignition has been switched off for more than one minute, by press-ing the stalk downwards.