Peugeot 307 CC Dag 2004.5 Owner's Guide

22
30-08-2004
23
30-08-2004
INSTRUMENTS AND CONTROLS
Park
Selector lever positions on
the automatic gearbox displayAutomatic gearbox indicator
lights
Reverse
Neutral
Drive
Manual mode :
1st gear engaged
2nd gear engaged
3rd gear engaged
4th gear engaged "SPORT" indicator light
This comes on when the "SPORT" program is selected.
"SNOW" indicator light
This comes on when the "SNOW" program is selected.
Operating fault
This is displayed when an
operating fault occurs, ac-
companied by the message
"Automatic gearbox fault"
on the multi-function display,
an audible signal and lashing of the
Sport and Snow indicator lights on
the instrument panel.
Examples:
"SPORT"
program and Park position.
"SNOW" program and Drive position.

24
30-08-2004
25
30-08-2004
INSTRUMENTS AND CONTROLS
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset (see correspond-
ing section). It is determined by two
parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
Example: 4,800 miles/km remain
before the next service. For ive sec-
onds after the ignition is switched on,
the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) re-
main before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit.
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.

24
30-08-2004
25
30-08-2004
INSTRUMENTS AND CONTROLS
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset (see correspond-
ing section). It is determined by two
parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
Example: 4,800 miles/km remain
before the next service. For ive sec-
onds after the ignition is switched on,
the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) re-
main before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit.
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.

24
30-08-2004
25
30-08-2004
INSTRUMENTS AND CONTROLS
The service is overdue.
The service spanner lashes for
5 seconds after the ignition is
switched on.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
Lack of oil
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 10 seconds, after the
service information.
Oil level gauge fault
The level read on the dipstick
will only be correct if the vehicle
is on level ground and the en-
gine has been off for more than
15 minutes.

5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service. Check the oil level using the dip-
stick.
If the level is correct, the lashing in-
dicates an actual malfunction of the
engine oil level gauge.
Contact a PEUGEOT dealer.
Flashing indicates a lack of oil which
could damage the engine.
If the lack of oil is conirmed by a
check using the dipstick, it is essen-
tial that the level is topped up.

26
30-08-2004
Lighting rheostat
With the lights on,
press the button to
vary the intensity of
the lighting of the
instruments and con-
trols. When the lighting
reaches the minimum
(or maximum) setting, release the
button then press it again to increase
(or reduce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Trip recorder zero
reset button
With the ignition on,
press the button until
the zeros appear.
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows
"0000.0",
release the button; the service sym-
bol disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
INSTRUMENTS AND CONTROLS

24
30-08-2004
25
30-08-2004
INSTRUMENTS AND CONTROLS
The service is overdue.
The service spanner lashes for
5 seconds after the ignition is
switched on.
Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
Lack of oil
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 10 seconds, after the
service information.
Oil level gauge fault
The level read on the dipstick
will only be correct if the vehicle
is on level ground and the en-
gine has been off for more than
15 minutes.

5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service. Check the oil level using the dip-
stick.
If the level is correct, the lashing in-
dicates an actual malfunction of the
engine oil level gauge.
Contact a PEUGEOT dealer.
Flashing indicates a lack of oil which
could damage the engine.
If the lack of oil is conirmed by a
check using the dipstick, it is essen-
tial that the level is topped up.

27
30-08-2004
YOUR 307 CC IN DETAIL
Monochrome screen B
This enables the following informa-
tion to be displayed:
- the time,
- the date,
- the outside temperature (it lashes when there is a risk of ice),
- the radio displays,
- the status of the openings (doors, bonnet...),
- the warning messages (e.g. "Bat- tery charge fault") or information
messages (e.g. "Passenger air bag
deactivated") displayed temporarily
can be cleared by pressing button
1 or 2,
- the trip computer (see correspond- ing section).
MULTI-FUNCTION SCREENS
PresentationMonochrome screen CT and colour
screen DT
These two systems are controlled
by the RT3 GPS audio/telephone
keypad.
They enable the following informa-
tion to be displayed:
- the time,
- the date,
- the outside temperature (a mes- sage warns you when there is a
risk of ice),
- the audio source displays (radio, CD, ...),
- the telematic system displays (tele- phone, services, ...),
- the status of the openings (doors, bonnet, ...),
- the warning messages (e.g. "Fuel level low") and vehicle functions
status messages (e.g. "Passenger
air bag deactivated") displayed
temporarily,
- the trip computer display (see cor- responding section),
- the satellite navigation system dis- plays (see corresponding section).
Note: to enable you to use all of
your system's functions, you have
two CD ROMs: one, "Coniguration",
contains the software and the vari-
ous display and spoken information
languages, the other, "Navigation",
contains the satellite navigation sys-
tem map data.
Press the RT3 audio/telephone "MENU" button to access the general menu and
select one of the following applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 Audio/ telephone" section),
- trip computer (see corresponding section),
- directory (see "RT3 audio/tele- phone" section),
- telematics (see "RT3 audio/tele- phone" section),
- coniguration (see corresponding section).
Monochrome screen CT
General menu

28
30-08-2004
29
30-08-2004
YOUR 307 CC IN DETAIL
Press the RT3 audio/telephone "MENU" button to access the general
menu and select one of the following
applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 audio/ telephone" section),
- trip computer (see corresponding section),
Colour screen DT
General menu
- directory (see "RT3 audio/tele-phone" section),
- telematics (see "RT3 audio/tele- phone" section),
- coniguration (see corresponding section),
- map (see section "Satellite naviga- tion system"),
- video (see corresponding section).
Monochrome screen B
Press button 1 for two seconds to
gain access to the settings .
Then, each press of this button permits
scrolling of the various parameters.
- language of the information dis- played,
- unit of speed (km or miles),
- unit of temperature (degrees Celsius or Fahrenheit),
- time format (12 or 24 hours),
- hour,
- minute,
- year,
- month,
- day.
Pressing button
2 enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After seven seconds without action,
the screen returns to the usual dis-
play, the modiied data are recorded.
Parameter coniguration
A few deinitions
Superimposed display
a window appears over the current
application for a short while, to an-
nounce a change of status of another
application.
Permanent application
main application currently in use, dis-
played in the main screen window.
Contextual menu
limited menu associated with the
main application currently in use, dis-
played in the main screen window.

28
30-08-2004
29
30-08-2004
YOUR 307 CC IN DETAIL
Press the RT3 audio/telephone "MENU" button to access the general
menu and select one of the following
applications:
- navigation - guidance (see section "Satellite navigation system"),
- audio functions (see "RT3 audio/ telephone" section),
- trip computer (see corresponding section),
Colour screen DT
General menu
- directory (see "RT3 audio/tele-phone" section),
- telematics (see "RT3 audio/tele- phone" section),
- coniguration (see corresponding section),
- map (see section "Satellite naviga- tion system"),
- video (see corresponding section).
Monochrome screen B
Press button 1 for two seconds to
gain access to the settings .
Then, each press of this button permits
scrolling of the various parameters.
- language of the information dis- played,
- unit of speed (km or miles),
- unit of temperature (degrees Celsius or Fahrenheit),
- time format (12 or 24 hours),
- hour,
- minute,
- year,
- month,
- day.
Pressing button
2 enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After seven seconds without action,
the screen returns to the usual dis-
play, the modiied data are recorded.
Parameter coniguration
A few deinitions
Superimposed display
a window appears over the current
application for a short while, to an-
nounce a change of status of another
application.
Permanent application
main application currently in use, dis-
played in the main screen window.
Contextual menu
limited menu associated with the
main application currently in use, dis-
played in the main screen window.

28
30-08-2004
29
30-08-2004
YOUR 307 CC IN DETAIL
CT monochrome screen
The "Display Coniguration" menu gives
access to the following parameters:
• "Adjust the brightness": display brightness setting,
• "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter: insert the coniguration
CD-Rom); setting of the spoken
commands,
• "International parameters": date and time setting (12 or 24 hour mode,
adjustment of the minutes on GPS);
units setting (l/100 - °C or mpg
- °F),
• "Choice of language": selection of the language for the display, informa-
tion and voice commands (German,
English, Spanish, French, Italian,
Dutch, Portuguese: insert the con-
iguration CD ROM).
DT colour screen
The "Coniguration" menu gives
access to the following parameters:
• "Choose colours": selection from the palette of colours available for
display,
• "Luminosity and brightness": dis- play brightness setting,
• "Sound": voice synthesiser setting (for the masculine/feminine voice
parameter: insert the coniguration
CD-Rom); setting of the spoken
commands,
• "International parameters": date and time setting (12 or 24 hour mode,
adjustment of the minutes on GPS);
units setting (l/100 - °C or mpg - °F),
• "Choice of language": selection of the language for the display, informa-
tion and voice commands (German,
English, Spanish, French, Italian,
Dutch, Portuguese: insert the con-
iguration CD ROM).
Video
It is possible to connect video equip-
ment (a camcorder, digital camera, ...)
using the three video sockets situated
inside the glove box.
It is only possible to display video
images when the vehicle is sta-
tionary.
Select the "Video" menu from the main menu :
- "Activate video mode" to activate/
cancel the video function,
- "Video parameters" to adjust the display format, the brightness, con-
trast and colour.
Press
"MODE" or "DARK" to exit
video mode.
Successive presses on the
"SOURCE"
button allow you to select another au-
dio source other than the video.
For safety reasons, con-
iguration of the multi-
function screens by the
driver must be carried out
when stationary.