headlamp Peugeot 307 CC Dag 2007.5 Owner's Manual

i
63
VISIBILITY
For vehicles i tted with halogen
bulbs, depending on the load in your
vehicle, adjusting the beam of your
headlamps is recommended.

0. 1 or 2 people in the front seats.

-. 3 people.

1. 4 people.

-. Intermediate setting.

2. 4 people + maximum authorised
loads.

-. Intermediate setting.

3.
Driver + maximum authorised loads.

Initial setting is position 0. On vehicles with xenon bulbs:

when stationary , the system auto-
matically corrects the height of the
beam, whatever the load of the vehi-
cle. The driver is then assured of hav-
ing optimum lighting and not causing
a nuisance to other road users.

In cases of malfunction ,
the service warning light
comes on on the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction display.
The system places your headlamps
to the low position.

Do not touch the xenon bulbs. Contact
a PEUGEOT dealer.
Daytime lights *
On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.
This warning light comes
on on the instrument panel. THE HEADLAMPS
AUTOMATIC HEADLAMP
ADJUSTMENT
The instruments and controls
(instrument panel, multifunction
display, air conditioning control
panel, ...) are only lit on switch-
ing to the automatic switching on
of the lights mode or when the
lights are switched on manually.

64
VISIBILITY
Special position of the front
windscreen wiper
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
the windscreen.
This action enables you to position
the wiper blades for winter parking,
cleaning or replacement (See section
"Practical information - Changing a
wiper blade").
To park the wipers after this has
been done, switch on the ignition and
operate the stalk.
Windscreen and headlamp wash
Pull the windscreen wiper stalk to-
wards you. The windscreen wash
then the windscreen wipers operate
for a i xed period.
The headlamp wash is also activated,

if the headlamps are on.

2 Fast wipe (heavy rain).

1 Normal wipe (moderate rain).

I Intermittent wipe.

0 Off.

 Single wipe (press downwards).
In the I ntermittent position, the wiping
speed is in proportion to the vehicle
speed.
2 Fast wipe (heavy rain).

1 Normal wipe (moderate
rain).

I Intermittent wipe.

0 Off.

AUTO
 Automatic or single wipe
(press downwards).
In the I ntermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In AUTO mode, the wiping speed is
in proportion to the intensity of the
rainfall. The i rst press of the stalk
downwards activates the automatic
wipe.
Subsequent presses trigger a single
wipe. WINDSCREEN WIPER STALK
Front windscreen wiper with
intermittent wipe Front windscreen wiper with
automatic wipe

95
CHECKS
CHECKING THE LEVELS
There are two marks on
the dipstick:

A = maximum
Never i ll past this mark.

B = minimum
Oil change
According to the information given in
the servicing booklet.
Power steering reservoir
Remove the style trim * (see §
"Changing a bulb - Front lights").
Open the reservoir, with the engine
at ambient temperature. The level
should always be above the MIN.
mark and close to the MAX. mark.
Dipstick
Cooling system
Use the l uid recommended by the
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. This fan can oper-
ate with the ignition off.

In the case of vehicles i tted with
a particle emission i lter, the fan
can operate after the vehicle has
stopped, even when the engine is
cold.
In addition, as the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying out any work.
Slacken the cap by two turns to re-
lease the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and
top up the level.
Windscreen and headlamp
wash level
Diesel additive level (Diesel
with particle emission filter)
If the service warning light comes on,
accompanied by a message and an
audible signal, this indicates a low
diesel additive level.
This additive must be topped up.
Contact a PEUGEOT dealer as soon
as possible.
Brake fluid level
Viscosity selection
In all cases, the oil selected must
meet the manufacturer's require-
ments.
Oil level

Note: the coolant does not need to
be changed.
The level should always be
above the MIN mark and
close to the MAX mark. Replacement must be car-
ried out according to the
manufacturer's servicing
schedule.
Use l uids recommended by the
manufacturer, which fuli l DOT4
standards.
Check the level regularly
and top up between chang-
es. The maximum consump-
tion is 0.5 l per 600 miles
(1 000 km).
Check the level with the vehicle level,
engine cold, using the oil level gauge
on the instrument panel or the dip-
stick.

For best quality cleaning and
for your safety, we would advise
that you use products recom-
mended by PEUGEOT.

To maintain the reliability of
engines and emission control
systems, the use of additives in
engine oil is prohibited.
* According to engine.

10
i
101
PRACTICAL INFORMATION
In the engine compartment, on the right-
hand side, remove the style trim * :
- press the centre of each plastic stud A ,
- remove each plastic stud,
- remove the style trim.
When you have i nished, do not for-
get to put everything back in place
correctly:
- position the style trim * ,
- rei t each plastic stud A by press-
ing on it. 1. Dipped beam headlamps
(H1-55 W or xenon bulb).

WARNING: RISK OF ELECTROCU-
TION
Xenon bulbs must be changed by a
PEUGEOT dealer.
2. Main beam headlamps (H7-55 W).

 Remove the protective cover cor-
responding to the faulty bulb.

 Disconnect the connector.

 Press the end of each securing
clip. Change the bulb.
When i tting the new bulb, ensure
that the direction notches are po-
sitioned correctly and the securing
clips are i xed properly.
 Reconnect the connector.

 Rei t the protective cover.
CHANGING A BULB
Front lights
Handle the bulbs with a dry cloth.
The headlamps are i tted with
polycarbonate glass with a pro-
tective coating. Do not clean
them with a dry or abrasive
cloth, nor with a detergent or
solvent product.
Use a sponge and soapy water.
* According to engine.

10
i
102
PRACTICAL INFORMATION

 Push the repeater forwards and
release it.


Remove the repeater and change it.

These can be obtained from a PEUGEOT
dealer.
3 Side lights (W 5 W).

 Remove the protective cover cor-
responding to the faulty bulb.

 Disconnect the connector.

 Remove the bulb and change it.
4. Direction indicators (PY 21 W amber).

 Turn the bulb holder a quarter of
a turn and remove it.

 Change the bulb.

Note : in certain climatic conditions
(low temperature, humidity), conden-
sation inside the headlamp glass is
normal ; it disappears a few minutes
after the lights are switched on. Contact a PEUGEOT dealer to have
these bulbs changed.
5. Fog lamps (H11-55 W). Integrated direction indicator side
repeaters.
Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
specii cation and colour.