Peugeot 307 SW 2004 Repair Manual

15-03-200415-03-2004
5859
Services* Emergency call*"PEUGEOT Assistance" /
Emergency call
During a connection to "PEUGEOT
Assistance" or an emergency call,
it is not possible to send or receive
calls or SMS messages; these will
be transferred to your voice mail.
In this case, a green diode flashes
on the RT3 GPS audio/telephone
panel, when the emergency call
or "PEUGEOT Assistance" call
procedure begins, then lights con-
tinuously when the call is taken by
the services concerned.
If your call to "PEUGEOT Assist-
ance" is located, a star "¨" will
appear in the text on the screen.
YOUR 307 SW IN DETAIL
Press button E to dis-
play the "Services"
menu and select one of
the following services:
•
฀ "Customer Contact Centre"
which enables you to contact the
PEUGEOT Customer Contact
Centre directly and access the
services offered (this type of call
is suspended if an emergency or
breakdown call is made).
•฀ "PEUGEOT Assistance" which
enables you to contact the
call centre which controls the
PEUGEOT breakdown service
directly and receive rapid assist-
ance (you have 6 seconds within
which to cancel the call when it
is made). During the breakdown
call phase it is not possible to
make any other calls with the
exception of emergency calls.
If you have signed the specific
PEUGEOT contract, your call will
be located.
•฀ "Operator services" which gives
access to the list of services specif-
ic to your operator (e.g.: customer
service, consumption monitor-
ing, news, stock market, weather,
travel, games, etc) if they are avail-
able.
In an emergency, press
button V until a signal is
heard and a call validation /
deletion screen is displayed
(delay of 6 seconds) or enter
112 directly.
Make an emergency call if
you are involved in an situ-
ation which leads you to fear serious
consequences (injuries, ...) for those
who are exposed to it (if you witness
or are involved in an accident result-
ing in injuries, an attack, ...).
Before making a call of this kind, the
audio/telephone must detect a cel-
lular network.
If you have not signed the speciic
PEUGEOT contract, the parameters
of the SOS button are set so that a
call is made to 112 - unique number
made available by the worldwide
GSM network, reserved for emer-
gency calls.
No security mode is required and,
depending on the network, you do
not need to insert your SIM card or
enter your PIN.
If you have signed the speciic
PEUGEOT contract, your call will
be located and you will be put in
contact with a PEUGEOT assist-
ance team.
For further details, refer to the gen-
eral conditions of your contract.
* If option and service available.

15-03-200415-03-2004
5859
The Directory
General
The "Directory" application gives
access to 400 iles divided into 4 in-
dependent sub-directories ("User1",
"User2", "User3" and "User4"). It
enables you to manage these iles,
make calls using the SIM card and
activate guidance.
Main menu
YOUR 307 SW IN DETAIL
From the general menu , select the
"Directory" application to access its
main menu and select one of the fol-
lowing functions:
• "Call", to call a number stored in a ile,
• "Activate guidance to", to initiate guidance to a location stored in a
ile,
• "Managing directory records", to add, delete, modify and consult di-
rectory iles or exchange them with
the SIM card,
• "Directory coniguration", to select the working directory and deine
the directory when the system is
switched on. Creation / Modiication of a ile
To create a ile, from the
"Directory"
menu, select the function "Managing
directory records" then "Add".
On the ile select the section to be
illed in, validate then enter the in-
formation.
To modify an existing ile, select it
using the "Consult or modify the
record" function of the "Managing
directory records" menu then make
the modiications.
Note: when the address is entered,
the navigation CD-Rom must be
present in order to obtain guidance
to this destination. Description of a directory ile
When a description is linked to a
directory ile, you can record the
description vocally so that it can be
used subsequently for direct access
by voice commands (e.g.:
"Call"
"[Name of the voice description]"
or "Guide to" "[Name of the voice
description]" ).
Select "Consult or modify the
record" from the "Managing directory
records" menu to access the screen
which permits entering and recording
of the description.
Press the record button and follow
the instructions.
TMC (Trafic Message Channel)
RDS Trafic Information
You can access information regard-
ing the trafic conditions from the
"Audio functions"
or "Telematics"
menu, then from the "Trafic Infor-
mation TMC" function (see section
"Satellite navigation system").

15-03-200415-03-2004
6061
VOICE COMMANDS
The voice commands make it pos-
sible to use pre-recorded words or
phrases to control a certain number
of functions of the RT3 GPS audio/telephone.
Activation of the voice commands
Press the button on the end of the
lights stalk to activate or deactivate
this function.
Example: to recall the radio station
stored on button 3, the key words
are: "Radio" "Memory" "3" .
To use these key words, you must
say the word "Radio", wait for the
audible conirmation signal, then
say the word "Memory", wait for the
audible conirmation signal, then end
with the word "3", wait for the audible
conirmation signal which will carry
out the action requested.
Notes:
- between two key words, a screen indicates the time remaining and
the key word recognised,
- in the absence of any voice commands, this function will be
switched off after approximately
ive seconds,
- if a command is not understood, the system transmits "Pardon"
and displays "Word not recog-
nised" on the screen.
Saying the phrase "Help" or "What
can I say" displays all of the com-
mands available on the screen. List of commands available
- For the radio, say "RADIO", then:
"PREVIOUS" / "NEXT" /
"MEMORY" + 1...6 /
"AUTOSTORE" / "LIST"
- For the CD, say "CD PLAYER", then:
" PREVIOUS TRACK" / "NEXT TRACK" / "TRACK NUMBER" +
1...20 / "RANDOM" / "SCAN" /
"LIST"
- For the CD changer, say "CHANGER", then:
" PREVIOUS TRACK" / "NEXT TRACK" / "TRACK NUMBER" +
1...20 / "PREVIOUS DISC" /
"NEXT DISC" /
"DISC NUMBER" + 1...5 / "RANDOM" / "SCAN" /
"REPEAT" / "LIST"
- For the telephone, say "TELEPHONE", then:
"REDIAL" / "ADDRESS BOOK" + DESCRIPTION / "SERVICES" /
"SOUND BOX" / "VOICE
MESSAGE"
- For the SMS text messages, say "SMS" or "MESSAGE" then:
"DISPLAY" / "READ"
- For the RDS traffic information TMC, say "TRAFFIC-INFO" then:
"DISPLAY" / "READ"
YOUR 307 SW IN DETAIL
- For navigation/guidance, say "NAVIGATION" or "GUIDANCE",
then:
"STOP" / "RE-START" / "ADDRESS BOOK" +
DESCRIPTION / "ZOOM IN" /
"ZOOM OUT" / "SHOW" +
"DESTINATION" / "SHOW" +
"VEHICLE"
- To change the permanent application, say "DISPLAY", then:
"AUDIO" / "TELEPHONE" / "NAVIGATION" / "TRIP
COMPUTER" / "GUIDANCE"
- To call someone recorded in the directory directly, say "CALL" +
DESCRIPTION
- To be guided to the address of someone recorded in the
directory, say "GUIDE TO" +
DESCRIPTION
- Various:
"CANCEL" / "HELP" / "WHAT CAN I SAY" / "STOP" /
"DELETE" / "YES" / "NO" /
"PREVIOUS" / "NEXT"

15-03-200415-03-2004
6061YOUR 307 SW IN DETAIL
CD CHANGER
This is located in the centre of the
fascia under the radio. It holds up to
5 discs.
To load the changer, insert the discs
with the printed side upwards.
To remove a disc, press and hold one
of the buttons "1" to "5" .
The use of copied com-
pact discs may cause
faults.
Insert circular compact
discs only.

62
15-03-2004
63
15-03-2004
SATELLITE NAVIGATION
SYSTEM
Introduction
The satellite navigation system guides
you, by means of vocal and visual in-
structions (graphics), to your chosen
destination.
The heart of the system lies in the
use of a map data base and
GPS
(Global Positioning System) . With
this system you can ix the position
of your vehicle by means of a satel-
lite network.
The system uses the following ele-
ments:
- the CD-Rom drive,
- the coniguration CD-Rom,
- the navigation CD-Rom,
- the last voice message recall con- trol,
- the control keypad,
- the CT monochrome screen or the DT colour screen.
For safety reasons, the
inputting of navigation
information by the driver
must be carried out when
the vehicle is stationary.
The CD-Rom drive
This is part of the RT3 GPS audio/
telephone.
1. Ejection button on CD-Rom.
2. CD-Rom housing.
The navigation CD-Rom The last voice message recall
control.
Pressing for more than two seconds on
the button at the end of the lights stalk
repeats the last voice information.
YOUR 307 SW IN DETAIL
This contains all the map data.
It must be inserted in the drive, print-
ed face upwards.
Use only CD-Roms approved by
PEUGEOT.
Certain functions or services de-
scribed may vary depending on
the version of CD-Rom or the
country where the vehicle is sold.

62
15-03-2004
63
15-03-2004
YOUR 307 SW IN DETAIL
The control keypad
This lets you select and validate the
functions, controls and programmes
displayed. Rotation of the dial:
This allows you to
move round the
screen and thus select a function.
It also allows you:
- with a 'setting' type parameter,
after selection, to increase or de-
crease the value,
- with a 'list' type parameter, to open
the list and scroll through the val-
ues,
- with map guidance, to increase the
zoom .
Pressing the dial:
This allows:
- access to the list of controls (con-
textual menu) of the permanent
display, if there is no other display
superimposed.
- conirmation of the selected func-
tion or the modiied value.
- selection of a 'setting' or 'list'
type parameter for modiication. "MODE" button:
- brief press: modiication of per-
manent display (audio system,
navigation/guidance...),
- Press for more than two seconds: display of general information .
'ESC' button:
- brief press: cancelling of opera-
tion in progress or erasing of last
superimposed display.
- pressing for more than two sec- onds: erasing of all superimposed
displays and return to the perma-
nent display.
'MENU' button:
- Brief press: access to the general
menu .
- Press for more than two seconds: access to the help menu.
Tip:
You can access the general menu
by pressing the dial of the RT3 GPS
audio/telephone .

64
15-03-2004
65
15-03-2004
General notes on the display
Monochrome screen CT Colour screen DTGeneral menu
Switch on the RT3 GPS audio/
telephone and insert the navigation
CD-Rom.
Press the
"MENU" button to access
the general menu .
Select the Navigation/Guidance icon
using the dial G, then validate by
pressing the dial to access the main
"Navigation - Guidance" menu.
YOUR 307 SW IN DETAIL
1
76547654
31232
During guidance, if the navigation
CD-Rom is present, the screen dis-
plays different information depend-
ing on the manoeuvres to be carried
out.
1. Current manoeuvre or com-
pass or course (if calculation in
progress or zone not mapped).
2. Next manoeuvre to be carried
out.
3. Next road to be taken.
4. Current road.
5. Estimated time of arrival at desti-
nation.
6. Distance to inal destination.
7. Distance to next manoeuvre. Notes:
- depending on the situation of the
vehicle and on the reception of
GPS information, this information
may disappear from the screen
temporarily,
- during guidance, the navigation CD ROM must remain in the RT3 GPS
audio/telephone.

64
15-03-2004
65
15-03-2004
Navigation - Guidance Selecting a destination Entering an address
The main "Navigation - Guidance"
menu offers various options for acti-
vation or management of guidance:
- choice of the type of destination address (entering of address,
service, GPS co-ordinates, stored
address),
- modiication to the initial route (en- tering of a diversion),
- displaying of the chosen destina- tion,
- setting of the guidance option pa- rameters,
- stop or resume guidance (display- ing of the message which changes
depending on the previous status). The
"Destination choice" menu
offers various options for reaching a
destination: •฀ entering a postal address,
•฀ selecting a service available in a
town (town hall, hotel, cinema, air-
port...),
•฀ entering GPS details,
•฀ selecting a destination stored in the
directory,
•฀ selecting one of the previous
destinations. The last guidance address is dis-
played.
Select and validate in succession the
entry zones
"Town", "Road" , then
"N°" to ill them in.
The "OK" function permits valida-
tion of the address and access to the
guidance activation function.
The "Store" function permits record-
ing of the address in a directory ile.
The "Curr. loc" function permits dis-
play of the current address.
YOUR 307 SW IN DETAIL

66
15-03-2004
67
15-03-2004
Entering the name of the town
To enter the name of a town, select
each letter by turning the dial, then
validate each letter by pressing the
dial.
If an error is made entering the let-
ters, the "Change" function permits
erasing of the last letter entered.
Note: following the validation of a
letter, only those which could make
up a name existing in the database
appear.
As letters are entered, the "List"
function indicates the number of
towns beginning with the same let-
ters. Activation of this function per-
mits selection of a town from the list. When the list contains fewer than ive
names, these are displayed automat-
ically. Select a town then validate by
pressing the dial.
When the complete name of the town
is displayed, select the
"OK" function
then conirm by pressing the dial.
Note: once the town has been en-
tered, you can conirm by pressing
"OK" . You will then be guided to the
centre of this town automatically.
Entering the name of the road
Enter the name of the street in the
same way as the name of the town.
When the full name of the street is
displayed, select the "OK" function
then conirm by pressing the dial.
Entering the town and road using
the alphanumeric keypad
Press the numeric key which corre-
sponds to the letter required until the
letter appears on the screen, then
conirm by pressing the # key after
each letter. Entering the number of the road
or junction
Enter the number of the street previ-
ously entered.
Select the
"OK" function, then con-
irm by pressing the dial.
Note: if the number of the street en-
tered is not available, it is rejected.
You can also select a street from the
"Junctions" function, which avoids
having to enter the street number.
Note: if the street selected does not
have a number, the list of junctions is
displayed automatically.
The full destination is displayed.
Select the "OK" function, then
conirm by pressing the dial to ac-
cess the guidance activation func-
tion. Follow the instructions given
by the system.
YOUR 307 SW IN DETAIL

66
15-03-2004
67
15-03-2004
Selecting a service
If you wish to be directed to a serv-
ice, select the category correspond-
ing to the service, then conirm by
pressing the dial.
The list of services corresponding to
the category selected is displayed.
Select the service then conirm
by pressing the dial to access the
"Choice of a location" function.
The last address entered is dis-
played.
There are three options for deining
the location in which you wish to ob-
tain this service:
- accept the last address entered us- ing the "OK" function,
- ill in the "Town" and "Road"
zones,
- automatically enter the name of your current location using the
"Curr. loc." function. Note:
if the service selected is not
available in the programmed loca-
tion, a temporary message informs
you of this.
Following validation of the location,
the service closest to it is displayed.
The distance indicated is the dis-
tance as the crow lies from the serv-
ice to the selected location.
An indication on the edge of the
screen (x/n) shows you the maximum
number of establishments providing
the same service within a radius of
30 miles (50 km), as the crow lies,
from the selected location.
Use buttons "<" and ">" to consult
the list provided.
When the establishment of your
choice is displayed, you can: •฀ select the "OK" function to activate
guidance towards this service,
•฀ select the "Store" function to enter
this establishment in your directory. GPS details
The most recent destinations are
shown.
There are three possible methods
of deining the location to which you
wish to travel:
- accept the last details input by
means of the "OK" function,
- input the details of your destina- tion,
- automatically input the details of your current location by means of
the "Curr. loc." function.
YOUR 307 SW IN DETAIL