Peugeot 307 SW 2005.5 Owner's Guide

Instruments and controls24 -
01-10-2005
25Instruments and controls-
01-10-2005
Coolant temperature indicator
When the needle is in zone A, the
temperature is correct.
When the needle is in zone B, the
temperature is too high. The cen-
tral STOP warning light lashes,
accompanied by an audible signal
and a message on the multifunction
display.
You must stop immediately.
Warning: wait for the engine to cool
before topping up the level.
The cooling system is pressurised.
In order to avoid any risk of scalding,
unscrew the cap two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level.
Contact a PEUGEOT dealer. Park

Automatic gearbox lever
positions indicator
Reverse
Neutral
Drive
Manual mode: 1st gear engaged
2nd gear engaged
3rd gear engaged
4th gear engaged
Engine oil temperature
indicator
When the engine is running, this
indicates the temperature of the oil.
The temperature is too high if the
maximum graduation is reached.
You must stop immediately.
Contact a PEUGEOT dealer.

Instruments and controls24 -
01-10-2005
25Instruments and controls-
01-10-2005
In the event of under-revving or over-
revving, the gear selected lashes for
a few seconds, then the actual gear
engaged is displayed.This comes on when the
"SPORT" programme on
the automatic gearbox is
selected.
This comes on when the
"SNOW" programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light This is displayed if a gear
is not engaged correctly
(selector between two posi-
tions).
"SPORT" indicator light
Invalid value during manual
operation
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information re-
lating to the cruise control or speed
limiter, when either of these is acti-
vated (see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset (see correspond-
ing section). It is determined by two
parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
Example: 4,800 miles/km remain
before the next service. For ive sec-
onds after the ignition is switched on,
the display indicates:

Instruments and controls26 -
01-10-2005
27Instruments and controls-
01-10-2005
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows "=0", re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The service spanner lashes for 5 sec-
onds after the ignition is switched on.
Example:
the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) re-
main before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.

Instruments and controls26 -
01-10-2005
27Instruments and controls-
01-10-2005
Lighting rheostat
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Trip recorder zero reset
button
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information.
Oil level correct
Oil level gauge fault
Flashing of "OIL --"
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes. Flashing of
"OIL",
linked with the
service warning
light, accompanied
by an audible sig-
nal and a message
on the multifunction display, indicates
a lack of oil which could damage the
engine.
If the lack of oil is conirmed by a
check using the dipstick, it is essen-
tial that the level is topped up.
Lack of oil
Dipstick
There are 2 marks on the
dipstick:- never exceed level A,
- in position B, top up the level via the oil iller cap,
using the type of oil suited
to your engine.
A = max.
B = min.

Instruments and controls24 -
01-10-2005
25Instruments and controls-
01-10-2005
In the event of under-revving or over-
revving, the gear selected lashes for
a few seconds, then the actual gear
engaged is displayed.This comes on when the
"SPORT" programme on
the automatic gearbox is
selected.
This comes on when the
"SNOW" programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light This is displayed if a gear
is not engaged correctly
(selector between two posi-
tions).
"SPORT" indicator light
Invalid value during manual
operation
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information re-
lating to the cruise control or speed
limiter, when either of these is acti-
vated (see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset (see correspond-
ing section). It is determined by two
parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
Example: 4,800 miles/km remain
before the next service. For ive sec-
onds after the ignition is switched on,
the display indicates:

Instruments and controls24 -
01-10-2005
25Instruments and controls-
01-10-2005
In the event of under-revving or over-
revving, the gear selected lashes for
a few seconds, then the actual gear
engaged is displayed.This comes on when the
"SPORT" programme on
the automatic gearbox is
selected.
This comes on when the
"SNOW" programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light This is displayed if a gear
is not engaged correctly
(selector between two posi-
tions).
"SPORT" indicator light
Invalid value during manual
operation
INSTRUMENT PANEL
DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and
trip distances).
Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information re-
lating to the cruise control or speed
limiter, when either of these is acti-
vated (see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last
indicator zero reset (see correspond-
ing section). It is determined by two
parameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display
indicates the number of miles [kilo-
metres] (rounded off) remaining until
the next service.
Example: 4,800 miles/km remain
before the next service. For ive sec-
onds after the ignition is switched on,
the display indicates:

Instruments and controls26 -
01-10-2005
27Instruments and controls-
01-10-2005
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows "=0", re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The service spanner lashes for 5 sec-
onds after the ignition is switched on.
Example:
the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) re-
main before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.

Instruments and controls26 -
01-10-2005
27Instruments and controls-
01-10-2005
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows "=0", re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The service spanner lashes for 5 sec-
onds after the ignition is switched on.
Example:
the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the service spanner remains lit. The
display indicates the total and trip
distance.
Note: the service spanner may also
come on if more than two years have
elapsed since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).
Example:
400 miles (900 km) re-
main before the next service.
For 5 seconds after the ignition is
switched on, the indicator displays:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.

Instruments and controls26 -
01-10-2005
27Instruments and controls-
01-10-2005
Lighting rheostat
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
Trip recorder zero reset
button
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information.
Oil level correct
Oil level gauge fault
Flashing of "OIL --"
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes. Flashing of
"OIL",
linked with the
service warning
light, accompanied
by an audible sig-
nal and a message
on the multifunction display, indicates
a lack of oil which could damage the
engine.
If the lack of oil is conirmed by a
check using the dipstick, it is essen-
tial that the level is topped up.
Lack of oil
Dipstick
There are 2 marks on the
dipstick:- never exceed level A,
- in position B, top up the level via the oil iller cap,
using the type of oil suited
to your engine.
A = max.
B = min.

Instruments and controls28 -
01-10-2005
29Instruments and controls-
01-10-2005
TRIP COMPUTERMonochrome screens A
- the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.
Each time the button on the end of
the wiper stalk is pressed, the vari-
ous items of trip computer data are
displayed in succession, depending
on the multifunction display: Zero reset
Press the stalk for more than two
seconds.
Monochrome screens C
- the
"vehicle" tab with:
• the range, the current consump- tion and the distance still to be
driven,
- tab "1" (route 1) with:
• the average speed, the average consumption and the distance
driven calculated over route
"1" ,
- tab "2" (route 2) with the same fea-
tures for a second route.
Zero re-set
When the required route is displayed,
press the button for more than two
seconds.