Peugeot 307 SW 2006 Owner's Guide

29
Colour screen DT
- the "Current information" with:• the range,• the current consumption,• the distance still to be driven.- "Route 1" with:• the distance travelled,• the average consumption,• the average speed,- "Route 2" with the same features for a second route.
Monochrome screen CT
-the "vehicle" tab with:• the range, the current consumptionand the distance still to be driven,- tab "1" (route 1) with:• the average speed, the average consumption and the distance driven calculated over route "1"-tab "2" (route 2) with the same features for a second route.
Zero re-set
When the required route is displayed, press the button for more than two seconds.Zero re-set
When the required route is displayed, press the button for more than two seconds.
This figure may increase if there is a change in the style of driving or the road surface, producing a sig-nificant drop in current consump-tion.
When the range is less than 20 miles (30 km), dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is displayed when it exceeds 62 miles (100 km).
If dashes are displayed for long periods instead of digits, contact a PEUGEOT dealer.
Current consumption
This is the average quantity of fuel con-sumed during the last few seconds.
This function is displayed only when the vehicle is travelling at a speed greater than 20 mph (30 km/h).
It can be displayed in litres/100, km/litre or mpg (refer to on-board com-puter configuration).
Average consumption
This is the average fuel consumption since the computer was last set to zero.
It can be displayed in litres/100, km/litre or mpg (refer to on-board com-puter configuration).
Distance travelled
This indicates the distance travelled since the computer was last set to zero.
Range
This shows the distance that can still be covered with the fuel remaining in the tank in accordance with the av-erage consumption over the last few miles (kilometres) driven.

30
The routes "1" and "2" are independ-ent but have identical application.
Route "1" for example allows you to make daily calculations and route "2" monthly calculations.
Distance remaining to be travelled
This is the distance remaining to the final destination. It can either be cal-culated continuously by the naviga-tion system if guidance is activated, or entered by the user.
If the distance is not entered, dashes are displayed in place of the digits.
Average speed
This is the average speed calculated since the computer was last set to zero (with the ignition on).
The routesAccess via the general menu
Screen C
Screen CT
Screen DT"On-board computer" menu
Press the "MENU" button to access the general menu.Select the icon "On-board computer", then validate to access its menu.Depending on the multifunction dis-play, this menu offers various choices:- Enter distance to destination,- Warning log.- Status of the functions.or- On-board computer configuration.- Diagnostics,- Status of the functions.
Enter distance to destination
If guidance has not been activated, this enables you to enter an approxi-mate distance to final destination value, to permit all of the on-board computer calculations.
Warning log
This summarises the active warning messages, displaying them in suc-cession on the multifunction display.
Status of the functionsThis summarises the active or not active status of the functions present on the vehicle.
On-board computer configuration
This function allows the distance to the destination to be input (when guidance is not activated; otherwise this information is given by the navi-gation system) and also changing of the units of measurement (°C or °F, km and litres or miles and gallons).
The consumption values (current or average) can be displayed in litres/100, km/litre or mpg.
Diagnostics
This presents the information relating to the warning log, as regards the en-ergy remaining in the back-up battery and the number of satellites which can be seen by the GPS system.

31
Presentation
This displays the following information:
- the time,- the date,- the outside temperature (this flashes if there is a risk of ice),- the status of the accesses (doors, boot, ...),- the warning messages (e.g.: "Emission control system faulty") or information messages (e.g.: "Auto lights on"), displayed temporarily, can be cleared by pressing the "ESC" button,- the trip computer (see corresponding section).
MONOCHROME SCREEN A
(without RD4 audio equipment)Parameter configuration
There are three display control buttons:
- "ESC" to abandon the operation in progress,- "MENU" to scroll through the menus or sub-menus,- "OK" to select the menu or sub-menu required.Press the "MENU" button to scroll through the various menus of the general menu:
- vehicle configuration,- options,- display settings,- languages,- units.Press the "OK" button to select the menu required.
General menu

32
Once the"Vehicle configuration"menu has been selected, you can activate or deactivate the following equipment:
- wiper linked with reverse gear,- automatic switching on of the lights,- "follow-me-home" lighting,- parking assistance.
Options
Once the "Options" menu has been selected, you can start diagnostics of the status of the equipment (active, not active, faulty).
Languages
Once the "Languages" menu has been selected, you can change the language used by the display (Français, Italiano, Nederlands, Portugues, Portugues-Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has been selected, you can gain access to the following settings:
- year,- month,- day,- hour,- minutes,- 12 or 24 hour mode.
Units
Once the "Units" menu has been selected, you can change the units of the following parameters:
- temperature (°C or °F),- fuel consumption (l/100, mpg or km/l).
Once you have selected a setting, press the "OK" button to change its value.
Wait for approximately ten seconds without any action to allow the changed data to be recorded or press the "ESC" button to cancel.
The display then returns to the normal display.For safety reasons, configu-ration of the multifunction displays by the driver must take place when stationary.
Vehicle configuration

33
MONOCHROME DISPLAY A
Press the "MENU" button to gain access to the general menu, then press the "" or "" buttons to scroll through the following items:
- radio-CD,- vehicle configuration,- options,- display settings,- languages,- units.Press the "OK" button to select the menu required.
Presentation
This displays the following information, via the RD4 audio equipment control keypad:
- the time,- the date,- the outside temperature (this flashes if there is a risk of ice),- the audio source displays (radio, CD, ...),- the status of the accesses (doors, boot, ...),- the warning messages (e.g.: "Emission control system faulty") or information messages (e.g.: "Auto lights on"), displayed temporarily, can be cleared by pressing the "ESC"button,- the trip computer (see corresponding section).
Radio-CD
With the RD4 audio equipment switched on, once the "Radio-CD" menu has been selected, you can activate or deactivate the functions linked with the use of the radio (RDS following, REG mode), the CD or the CD changer (introscan, random play, CD repeat).
Once the "Vehicle configuration" menu has been selected, you can activate or deactivate the following equipment:
- rear wiper linked with reverse gear,- automatic switching on of the lights,- "follow-me-home" lighting,- parking assistance.
Options
Once the "Options" menu has been selected, you can start diagnostics of the status of the equipment (active, not active, faulty).
General menuVehicle configuration

34
Display settings
Once the "Display settings" menu has been selected, you can gain access to the following settings:
- year,- month,- day,- hour,- minutes,- 12 or 24 hour mode.
Languages
Once the "Languages" menu has been selected, you can change the language used by the display (Français, Italiano, Nederlands, Portugues, Portugues-Brasil, Deutsch, English, Espanol).
Units
Once the "Units" menu has been selected, you can change the units of the following parameters:
- temperature (°C or °F),- fuel consumption (l/100, mpg or km/l).
Once you have selected a setting, press the "" or "" buttons to change its value.
Press the "" or "" buttons to move to the previous or next setting respectively.
Press the "OK" button to record the change and return to the normal display or press the "ESC" button to cancel.
For safety reasons, configu-ration of the multifunction displays by the driver must take place when stationary.

35
Presentation
It displays the following information:
- the time,- the date,- the exterior temperature (this flashes if there is a risk of ice),- the accesses check (doors, boot, ...),- the warning messages (e.g.: "Depollution system faulty") or information messages (e.g.: "Automatic headlamp lighting activated"), displayed temporarily, can be cleared by pressing the "ESC" button,- the trip computer (see correspond-ing section).
MONOCHROME DISPLAY C
(without RD4 audio equipment)
There are three buttons and a navigator to enable you to control the screen:
- "MENU" to display the general menu, - "MODE" to change the permanent application (trip computer, date, ...),- "ESC" to abandon the operation in progress,- Rotation of the navigator: move-ment on the display or changing of a setting,- Press on the navigator: confirma-tion of the selection.
Press the "MENU" button to access the general menu:
- trip computer (see corresponding section),- personalisation-configuration.
Turn the navigator to select the menu required, then confirm by pressing the navigator.
Once this menu has been selected, you can access the following functions:
- define the vehicle parameters,- display configuration,- selection of the language.
Parameter configurationGeneral menu
"Personalisation-
Configuration" menu

36
Selection of the language
Once this menu has been selected, you can change the language used on the display (Deutsch, English, Espanol, Français, Italiano, Nederlands, Portugues, Portugues-Brasil).
Display configuration
Once this menu has been selected, you can access the following settings:
- brightness-video setting,- date and time setting,- selection of the units.
Example: "Duration of the "follow-me-home" lighting"
For safety reasons, configu-ration of the multifunction displays by the driver must take place when stationary.
Define the vehicle parameters
Once this menu has been selected, you can activate or deactivate the following equipment:
- wiper linked with reverse gear,- automatic switching on of the lights,- "follow-me-home" lighting and duration,- parking assistance.
Once you have selected a setting, press the navigator.
Turn the navigator to change its value.
Press the navigator to record the change and move on to the next setting or press the "ESC" button to cancel.

37
MONOCHROME SCREEN C
Press the "MENU" button to gain access to the general menu:
- audio functions,- trip computer (see corresponding section),- personalisation-configuration,- telephone (hands-free kit).Press the "" or "" buttons to select the menu required, then confirm by pressing the "OK" button.
Presentation
This displays the following information, via the RD4 audio equipment control keypad:
- the time,- the date,- the outside temperature (this flashes if there is a risk of ice),- the audio source displays (radio, CD, ...),- the status of the accesses (doors, boot, ...),- the warning messages (e.g.: "Depol-lution system faulty") or information messages (e.g.: "Automatic headlamp lighting activated"), displayed tempo-rarily, can be cleared by pressing the "ESC" button,- the trip computer (see corresponding section).
"Audio functions" menu
With the RD4 audio equipment switched on, once this menu has been selected, you can activate or deactivate the functions linked with the use of the radio (RDS, REG, RadioText), the CD or the CD changer (introscan, random play, CD repeat).
Once this menu has been selected, you can gain access to the following functions:
- define the vehicle parameters,- display configuration,- selection of the language.
"Personalisation-Configuration" menuGeneral menu

38
Define the vehicle parameters
Once this menu has been selected, you can activate or deactivate the folllowing equipment:
- wiper linked with reverse gear,- automatic switching on of the lights,- "follow-me-home lighting" and duration,- parking assistance.
Selection of the language
Once this menu has been selected, you can change the language used by the display (Deutsch, English, Espanol, Français, Italiano, Nederlands, Portugues, Portugues-Brasil).
Display configuration
Once this menu has been selected, you can gain access to the following settings:
- brightness-video setting,- date and time setting,- selection of the units.
When you have selected a setting, press the "OK" button, then press the "" or "" buttons to change its value.
Press the "OK" button to record the change and move on to the next setting or press the "ESC" button to cancel.
Example: "duration of follow-me-home lighting"
For safety reasons, configu-ration of the multifunction displays by the driver must take place when stationary.