Peugeot 307 SW 2007 Owner's Manual

10
115
Fitting a wheel
 Position the wheel using the cen-tralising tool 5 to assist you.
 Tighten the bolts by hand and re-move the centralising tool 5.
 Partly tighten the bolts using the wheelbrace 1.
 Fold the jack 4 andremove it.
 Fully tighten the bolts using the wheelbrace 1.
 Replace the wheel trim, starting by placing the wheel trim notch opposite the valve, and press it on using the palm of the hand.
 Put the corresponding tools in the holder and secure its cover.
 Place the holder on the ground and align the spare wheel on it.
 Pass the notched hook into the holder cover.
 Refit the wheel under the vehicle tightening the winch control nut using the wheelbrace 1.
 Fully tighten and check that the wheel is horizontally flush against the rear floor.
 Close the flap using the lug to lock the winch.
 Store the rest of the tools in theright-hand trim of the boot.
For your safety, always change the wheel:
- on level, stable, non-slippery ground,- with the handbrake on and the igni-tion switched off,- with first or reverse gear engaged (position P for the automatic gear-box),- with the vehicle chocked.
Never go underneath a vehicle that is supported only by a jack (use a ramp).
Never refit the holder under the vehicle without the spare wheel.
Do not use a screwdriver in place of the wheelbrace to unwind or wind the winch.
Recommendations when using the temporary spare wheel*
Your vehicle may be equipped with a spare wheel which has a different rim to the standard wheel.
After use, have it replaced as quickly as possible.
Observe the following instructions in order to avoid altering the behaviour of the vehicle:
- do not exceed 50 mph (80 km/h),- do not fit a wheel trim,- drive with care,- check the tyre pressure indicated on the label.
* According to model and country.
After changing the wheel:
- have the correct positioning of the punctured wheel, the tightening of the bolts and the tyre pressure checked by a PEUGEOT dealer as soon as possible, - have the punctured tyre repaired and refit it to the vehicle as soon as possible,- have the correct positioning of the spare wheel checked by a PEUGEOT dealer.
Wheels fitted with the Tyre Under-Inflation Detection system
For further information refer to "Tyre under-inflation detection" in the safe-ty section.

10
116
Bolt covers
Alloy wheel bolts are covered by chrome trims.
Use the yellow tool 6 to remove the trims before slackening the bolts.
If your vehicle is fitted with a steel spare wheel, when fitting it, it is nor-mal when tightening the bolts to no-tice that the washers do not come into contact with the rim. The spare wheel is secured by the cone shape of each bolt.
Fitting snow tyres
If you fit snow tyres mounted on steel wheels onto your vehicle, it is essential to use special bolts available from your PEUGEOT dealer.
Special features of alloy wheelsFitting the spare wheelAnti-theft bolts
If your wheels are fitted with an anti-theft bolt (one per wheel), the chrome trim must be removed before un-screwing the bolt using the anti-theft socket and the wheelbrace.
This anti-theft socket was given to you on delivery of your vehicle along with the duplicate keys and the con-fidential card.
Make a careful note of the code number engraved on the head of the anti-theft socket. This will enable you to obtain a duplicate socket from a Peugeot dealer.

10
117
1. Dipped beam headlamps (H1-55 W or xenon bulb).
WARNING: RISK OF ELECTROCUTION
Xenon bulbs must be changed by a PEUGEOT dealer.
2. Main beam headlamps (H7-55 W).
 Remove the protective cover cor-responding to the faulty bulb.
 Disconnect the connector.
 Press the end of each securing clip. Change the bulb.
When fitting the new bulb, ensure that the direction notches are po-sitioned correctly and the securing clips are fixed properly.
 Reconnect the connector.
 Refit the protective cover.
Front lights
In the engine compartment, on the right-hand side, remove the style trim*:
- press the centre of each plastic stud A,- remove each plastic stud,- remove the style trim.
When you have finished, do not for-get to put everything back in place correctly:
- position the style trim*,- refit each plastic stud A by pressing on it.
Handle the bulbs with a dry cloth.
The headlamps are fitted with polycarbonate glass with a protective coating. Do not clean them with a dry or abrasive cloth, nor with a detergent or sol-vent product.
Use a sponge and soapy water.
CHANGING A BULB
* According to engine.

10
118
3. Side lights (W 5 W).
 Remove the protective cover cor-responding to the faulty bulb.
 Disconnect the connector.
 Remove the bulb and change it.
4. Direction indicators (PY 21 W amber).
 Turn the bulb holder a quarter of a turn and remove it.
 Change the bulb.
Note: in certain climatic conditions (low temperature, humidity), con-densation inside the headlamp glass is normal; it disappears a few minutes after the lights are switched on.
5. Fog lamps (H11-55 W).
Contact a PEUGEOT dealer to have these bulbs changed. Push the repeater forwards and release it.
 Remove the repeater and change it.
These can be obtained from a PEUGEOT dealer.
Amber coloured bulbs, such as the direction indicators, must be replaced with bulbs of identical specification and colour.
Integrated direction indicator side repeaters.

10
119
1. Brake lights (P 21 W).
2. Side lights (x 2) (R 5 W).
3. Direction indicators (P 21 W).
4. Reversing light (P 21 W), left side.
Fog lamp (P 21 W), right side.
These 6 bulbs are changed by removing the light:
 Remove the respective boot side trim to access the light,
 Remove the mounting nut for the light inside the boot.
 Remove the mounting nut for the light outside the boot.
 Remove the light.
 Unclip the harness.
 Press the tabs A and remove the bulb holder,
 Change the faulty bulb.
Note: if necessary use the wheel-brace to remove the nuts.
When refitting, take care to position the bulb holder and the bulb correctly.
Remove the tailgate upper trim carefully by unclipping it on either side, perpendicular to its direction of engagement.
Insert a screwdriver into the two outer holes B to press on the two tabs C.
 Push the light unit outwards while maintaining the pressure on the tabs.
 Pull the light unit outwards while tilting it.
 Change the faulty bulb.
 When refitting, ensure that the light unit tabs are engaged cor-rectly and that the tailgate upper trim has been put back in place correctly.
Number plate lights (W 5 W)
 Insert a small screwdriver in one of the external holes of the lens
 Push the lens outwards to unclip it.
 Remove the lens.
 Change the faulty bulb.
Third brake light:4 W 5 W bulbs.Rear lights

10
120
CHANGING A FUSE
The fuse boxes are placed in the low-er part of the fascia (passenger side) and in the engine compartment (left-hand side).
CorrectIncorrect
 Open the glove box lid to gain access to the fuses.
Fuse N°RatingFunctions
F115 ARear wiper.
F230 ALocking and deadlocking.
F35 AAir bags and pre-tensioners unit.
F410 A
Brake and clutch pedals switch, engine coolant level switch, steering wheel angle sensor, diagnostic socket, ESP sensor, electrochromatic mirror, particle emission filter pump.
F530 AFront electric windows and panoramic roof concealing shutter supply, heated mirrors.
Replacing a fuse
Before replacing a fuse, the cause of the incident must be found and recti-fied. The fuse numbers are indicated on the fuse box.
Always replace a faulty fuse with a fuse of the same rating (same col-our).
Use the special pliers located on the inside of the fascia fuse box cover, this support also contains the re-placement fuses.
Fascia fuses

10
120
CHANGING A FUSE
The fuse boxes are placed in the low-er part of the fascia (passenger side) and in the engine compartment (left-hand side).
CorrectIncorrect
 Open the glove box lid to gain access to the fuses.
Fuse N°RatingFunctions
F115 ARear wiper.
F230 ALocking and deadlocking.
F35 AAir bags and pre-tensioners unit.
F410 A
Brake and clutch pedals switch, engine coolant level switch, steering wheel angle sensor, diagnostic socket, ESP sensor, electrochromatic mirror, particle emission filter pump.
F530 AFront electric windows and panoramic roof concealing shutter supply, heated mirrors.
Replacing a fuse
Before replacing a fuse, the cause of the incident must be found and recti-fied. The fuse numbers are indicated on the fuse box.
Always replace a faulty fuse with a fuse of the same rating (same col-our).
Use the special pliers located on the inside of the fascia fuse box cover, this support also contains the re-placement fuses.
Fascia fuses

10
121
Fuse N°RatingFunctions
F630 ARear electric windows supply.
F75 AFront and rear courtesy lights, map reading lights, glove box light, concealing shutter control.
F820 AAudio equipment, audio/telephone, multifunction display, alarm siren, alarm unit, trailer fusebox, steering wheel controls supply.
F930 AFront 12 V socket, rear 12 V socket.
F1015 AAutomatic gearbox control unit, STOP switch, tyre under-inflation d etection control unit.
F1115 ADiagnostic socket, low current ignition switch, particle emission filter unit.
F1215 ARear parking assistance.
F135 AEngine fusebox supply, rain and brightness sensor.
F1415 ATrailer fusebox, instrument panel, automatic air conditioning, air bags and pre-tensioners unit, hands-free kit.
F1530 ALocking and deadlocking supply.
F16-PARC shunt.
F1740 AHeated rear screen.

10
122
Engine compartment fuses
To access the fuses located in the engine compartment (next to the bat-tery), unclip the fuse box lid.
When you have finished, close the lid carefully to guarantee the sealing of the fuse box.
Fuse N°RatingFunctions
F120 AEngine control unit and fan assembly high speed relays supply.
F215 AHorn.
F310 AFront and rear wash-wipe.
F420 AHeadlamp wash.
F515 AFuel pump and purge canister solenoid valve (2 litre petrol).
F610 AFour speed automatic gearbox control unit, automatic gearbox lever locking control, push control switch, fan assembly high speed relay, right and left xenon headlamps.
F710 AABS/ESP control unit, power steering electropump assembly control uni t.

10
123
Fuse N°RatingFunctions
F825 AStarter control.
F910 AAdditional heating unit (Diesel), coolant level switch.
F1030 AEngine control unit actuators (ignition coil, solenoid valves, oxygen sensors, control units, injectors, heaters), purge canister solenoid valve (1.6 litre petro l).
F1140 AAir conditioning blower.
F1230 AWindscreen wipers low/high speed.
F1340 ABuilt-in systems interface supply (ignition positive).
F1430 AAir pump (2 litre petrol).
F1510 ARight main beam headlamp.
F1610 ALeft main beam headlamp.
F1715 ALeft dipped headlamp.
F1815 ARight dipped headlamp.
F4115 ASix speed automatic gearbox control unit.