Peugeot 307 SW Dag 2006 Owner's Guide

1WARNING LIGHTS AND INDICATORS
29
Colour screen DT
- the "Current information" with:
• the range,
• the current consumption,
• the distance still to be driven.
- "Route 1" with:
• the distance travelled,
• the average consumption,
• the average speed,
- "Route 2" with the same features
for a second route.
Monochrome screen CT
- the "vehicle" tab with:
• the range, the current consumption and the distance
still to be driven,
- tab "1" (route 1) with:
• the average speed, the average consumption and the distance
driven calculated over route
"1"
- tab "2" (route 2) with the same
features for a second route.
Zero re-set
When the required route is displayed,
press the button for more than two
seconds. Zero re-set
When the required route is displayed,
press the button for more than two
seconds.This figure may increase if there is
a change in the style of driving or
the road surface, producing a sig-
nificant drop in current consump-
tion.
When the range is less than 20 miles
(30 km), dashes are displayed. After
filling with at least 5 litres of fuel, the
range is recalculated and is displayed
when it exceeds 62 miles (100 km).
If dashes are displayed for long
periods instead of digits, contact a
PEUGEOT dealer.
Current consumption
This is the average quantity of fuel con-
sumed during the last few seconds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
It can be displayed in litres/100, km/
litre or mpg (refer to on-board com-
puter configuration).
Average consumption
This is the average fuel consumption
since the computer was last set to
zero.
It can be displayed in litres/100, km/
litre or mpg (refer to on-board com-
puter configuration).
Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
Range
This shows the distance that can still
be covered with the fuel remaining in
the tank in accordance with the av-
erage consumption over the last few
miles (kilometres) driven.

1WARNING LIGHTS AND INDICATORS
30
The routes "1" and ‘’2’’ are inde-
pendent but have identical applica-
tion.
Route "1" for example allows you
to make daily calculations and route
"2" monthly calculations.
Distance remaining to be
travelled
This is the distance remaining to the
final destination. It can either be cal-
culated continuously by the naviga-
tion system if guidance is activated,
or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The routes Access via the general menu
Screen C
Screen CT
Screen DT
"On-board computer" menu
Press the
"MENU" button to access
the general menu.
Select the icon ‘’On-board compu-
ter’’ , then validate to access its menu.
Depending on the multifunction dis-
play, this menu offers various choices:
- Enter distance to destination,
- Warning log.
- Status of the functions.
or
- On-board computer configuration.
- Diagnostics,
- Status of the functions. Enter distance to destination
If guidance has not been activated,
this enables you to enter an approxi-
mate distance to final destination
value, to permit all of the on-board
computer calculations.
Warning log
This summarises the active warning
messages, displaying them in suc-
cession on the multifunction display.
Status of the functions
This summarises the active or not active sta-
tus of the functions present on the vehicle.
On-board computer configuration
This function allows the distance to
the destination to be input (when
guidance is not activated; otherwise
this information is given by the navi-
gation system) and also changing of
the units of measurement (°C or °F,
km and litres or miles and gallons).
The consumption values (current or
average) can be displayed in litres/
100, km/litre or mpg.
Diagnostics
This presents the information relating
to the warning log, as regards the en-
ergy remaining in the back-up battery
and the number of satellites which
can be seen by the GPS system.

2MULTIFUNCTION DISPLAYS
31
Presentation
This displays the following informa-
tion:
- the time,
- the date,
- the outside temperature (this flash-es if there is a risk of ice),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Emission control system faulty")
or information messages (e.g.:
"Auto lights on"), displayed tempo-
rarily, can be cleared by pressing
the "ESC" button,
- the trip computer (see corresponding section).
MONOCHROME SCREEN A
(without RD4 audio equipment)Parameter configuration
There are three display control buttons:
- "ESC" to abandon the operation in
progress,
- "MENU" to scroll through the men-
us or sub-menus,
- "OK" to select the menu or sub-
menu required. Press the "MENU" button to scroll
through the various menus of the
general menu:
- vehicle configuration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required.
General menu

2MULTIFUNCTION DISPLAYS
32
Once the "Vehicle configuration" menu
has been selected, you can activate or
deactivate the following equipment:
- wiper linked with reverse gear,
- automatic switching on of the lights,
- "follow-me-home" lighting,
- parking assistance.
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu
has been selected, you can gain ac-
cess to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Units
Once the "Units" menu has been se-
lected, you can change the units of
the following parameters:
- temperature (°C or °F),
- fuel consumption (l/100, mpg or km/l).
Once you have selected a setting,
press the "OK" button to change its
value.
Wait for approximately ten sec-
onds without any action to allow the
changed data to be recorded or press
the "ESC" button to cancel.
The display then returns to the nor-
mal display.
For safety reasons, configu-
ration of the multifunction
displays by the driver must
take place when stationary.
Vehicle configuration

2MULTIFUNCTION DISPLAYS
33
MONOCHROME DISPLAY A
Press the "MENU" button to gain ac-
cess to the general menu, then press
the " " or " " buttons to scroll
through the following items:
- radio-CD,
- vehicle configuration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required.
Presentation
This displays the following informa-
tion, via the RD4 audio equipment
control keypad:
- the time,
- the date,
- the outside temperature (this flash- es if there is a risk of ice),
- the audio source displays (radio, CD, ...),
- the status of the accesses (doors, boot, ...),
-
the warning messages (e.g.: "Emis-
sion control system faulty") or informa-
tion messages (e.g.: "Auto lights on"),
displayed temporarily, can be cleared
by pressing the "ESC" button,
- the trip computer (see correspond-
ing section). Radio-CD
With the RD4 audio equipment
switched on, once the "Radio-CD"
menu has been selected, you can
activate or deactivate the functions
linked with the use of the radio (RDS
following, REG mode), the CD or the
CD changer (introscan, random play,
CD repeat). Once the "Vehicle configuration" menu
has been selected, you can activate or
deactivate the following equipment:
- rear wiper linked with reverse gear,
- automatic switching on of the
lights,
- "follow-me-home" lighting,
- parking assistance.
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).
General menuVehicle configuration

2MULTIFUNCTION DISPLAYS
34
Display settings
Once the "Display settings" menu
has been selected, you can gain ac-
cess to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Units
Once the "Units" menu has been se-
lected, you can change the units of
the following parameters:
- temperature (°C or °F),
- fuel consumption (l/100, mpg or km/l).
Once you have selected a setting,
press the
" " or " " buttons to
change its value.
Press the " " or " " buttons to
move to the previous or next setting
respectively.
Press the "OK" button to record the
change and return to the normal dis-
play or press the "ESC" button to
cancel.
For safety reasons, configu-
ration of the multifunction
displays by the driver must
take place when stationary.

2MULTIFUNCTION DISPLAYS
35
Presentation
It displays the following information:
- the time,
- the date,
- the exterior temperature (this flash-es if there is a risk of ice),
- the accesses check (doors, boot, ...),
- the warning messages (e.g.: "De- pollution system faulty") or infor-
mation messages (e.g.: "Automatic
headlamp lighting activated"), dis-
played temporarily, can be cleared
by pressing the "ESC" button,
- the trip computer (see correspond- ing section).
MONOCHROME DISPLAY C
(without RD4 audio equipment)
There are three buttons and a navi-
gator to enable you to control the
screen:
- "MENU" to display the general
menu,
- "MODE" to change the permanent
application (trip computer, date, ...),
- "ESC" to abandon the operation in
progress,
- Rotation of the navigator: move-
ment on the display or changing of
a setting,
- Press on the navigator: confirma-
tion of the selection. Press the
"MENU" button to access
the general menu:
- trip computer (see corresponding section),
- personalisation-configuration.
Turn the navigator to select the menu
required, then confirm by pressing
the navigator.
Once this menu has been select-
ed, you can access the following
functions:
- define the vehicle parameters,
- display configuration,
- selection of the language.
Parameter configuration General menu
"Personalisation-
Configuration" menu

2MULTIFUNCTION DISPLAYS
36
Selection of the language
Once this menu has been selected,
you can change the language used
on the display (Deutsch, English,
Espanol, Français, Italiano, Nederlands,
Portugues, Portugues-Brasil).
Display configuration
Once this menu has been select-
ed, you can access the following
settings:
- brightness-video setting,
- date and time setting,
- selection of the units.
Example: "Duration of the "follow-
me-home" lighting"
For safety reasons, configu-
ration of the multifunction
displays by the driver must
take place when stationary.
Define the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- wiper linked with reverse gear,
- automatic switching on of the
lights,
- "follow-me-home" lighting and du- ration,
- parking assistance.
Once you have selected a setting,
press the navigator.
Turn the navigator to change its value.
Press the navigator to record the
change and move on to the next set-
ting or press the "ESC" button to
cancel.

2MULTIFUNCTION DISPLAYS
37
MONOCHROME SCREEN C
Press the "MENU" button to gain
access to the general menu:
- audio functions,
- trip computer (see corresponding section),
- personalisation-configuration,
- telephone (hands-free kit).
Press the " " or " " buttons to se-
lect the menu required, then confirm
by pressing the "OK" button.
Presentation
This displays the following informa-
tion, via the RD4 audio equipment
control keypad:
- the time,
- the date,
- the outside temperature (this flash-
es if there is a risk of ice),
- the audio source displays (radio, CD, ...),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "De- pollution system faulty") or infor-
mation messages (e.g.: "Automatic
headlamp lighting activated"), dis-
played temporarily, can be cleared
by pressing the "ESC" button,
- the trip computer (see correspond- ing section).
"Audio functions" menu
With the RD4 audio equipment
switched on, once this menu has
been selected, you can activate or
deactivate the functions linked with
the use of the radio (RDS, REG, Ra-
dioText), the CD or the CD changer
(introscan, random play, CD repeat). Once this menu has been selected,
you can gain access to the following
functions:
- define the vehicle parameters,
- display configuration,
- selection of the language.
"Personalisation-
Configuration" menu
General menu

2MULTIFUNCTION DISPLAYS
38
Define the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
llowing equipment:
- wiper linked with reverse gear,
- automatic switching on of the lights,
- "follow-me-home lighting" and du- ration,
- parking assistance. Selection of the language
Once this menu has been selected,
you can change the language used
by the display (Deutsch, English,
Espanol, Français, Italiano, Nederlands,
Portugues, Portugues-Brasil).
Display configuration
Once this menu has been selected,
you can gain access to the following
settings:
- brightness-video setting,
- date and time setting,
- selection of the units.
When you have selected a setting,
press the
"OK" button, then press
the " " or " " buttons to change
its value.
Press the "OK" button to record the
change and move on to the next set-
ting or press the "ESC" button to
cancel.Example: "duration of follow-me-
home lighting"
For safety reasons, configu-
ration of the multifunction
displays by the driver must
take place when stationary.