Peugeot 307 SW Dag 2007 Owner's Guide

24
In the event of under-revving or over-revving, the gear selected flashes for a few seconds, then the actual gear engaged is displayed.
This comes on when the "SPORT" programme on the automatic gearbox is selected.
This comes on when the "SNOW" programme on the automatic gearbox is selected.
Automatic gearbox indicator lights
"SNOW" indicator light
This is displayed if a gear is not engaged correctly (selec-tor between two positions).
"SPORT" indicator light
Invalid value during manual operation
After switching on the ignition, three functions are shown in succession:
- service indicator,- engine oil level indicator,- total distance recorder (total and trip distances).Note: the total and trip distances are displayed for 30 seconds when the ignition is switched off, on opening the driver’s door, as well as on lock-ing and unlocking the vehicle.
It also displays the information relat-ing to the cruise control or speed lim-iter, when either of these is activated (see corresponding section).
Service indicator
This indicates when the next service is due in accordance with the manu-facturer’s servicing schedule.
The point at which the next service is due is calculated from the last indi-cator zero reset (see corresponding section). It is determined by two pa-rameters:
- the distance travelled,- the time which has elapsed since the last service.Note: the distance remaining before the next service may be weighted by the time factor, depending on the us-er’s driving habits.
Operation
For 5 seconds after the ignition is switched on, the spanner symbolis-ing the servicing operations comes on; the distance recorder display in-dicates the number of miles [kilome-tres] (rounded off) remaining until the next service.
Example: 4,800 miles/km remain before the next service. For five sec-onds after the ignition is switched on, the display indicates:
INSTRUMENT PANEL
DISPLAY

25
5 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the display indicates the total and trip distance.
Your PEUGEOT dealer carries out this operation after each service.
However, if you carry out the service yourself, the re-set procedure is as follows:
 Switch off the ignition,
 Press and hold the trip recorder re-set button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0", re-lease the button; the spanner disap-pears.
Important: after this operation, if you wish to disconnect the battery, lock the vehicle and wait for at least five minutes, otherwise the zero re-set will not be registered.
The service is overdue.
The spanner flashes for 5 seconds after the ignition is switched on.
Example: the service is overdue by 300 miles/km, your vehicle must be serviced as soon as possible.
For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the spanner remains lit. The display indi-cates the total and trip distance.
Note: the spanner may also come on if more than two years have elapsed since the last service.
The distance remaining to the next service is less than 500 miles (1,000 km).
Example: 400 miles (900 km) remain before the next service.
For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the spanner remains lit.
It indicates that a service must be car-ried out soon. The display indicates the total and trip distance.
Service indicator zero re-set

26
With the lights on, press the button to vary the intensity of the lighting of the instruments and controls. When the lighting reaches the minimum (or maximum) setting, release the button then press it again to increase (or re-duce) the brightness.
As soon as the lighting is of the required brightness, release the button.
With the ignition on, press the button until the zeros appear.
Pressing the button enables you to alternate between the distance recorder and cruise control or speed limiter displays, when either of these is activated.
Engine oil level indicator
When the ignition is switched on, the engine oil level is indicated for a few seconds, after the service information.
Oil level correct
Oil level gauge fault
Flashing of "OIL --" indicates a malfunc-tion of the engine oil level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct if the vehicle is on level ground and the engine has been off for more than 15 minutes.
Flashing of "OIL", linked with the serv-ice warning light, accompanied by an audible signal and a message on the multifunction display, indicates a lack of oil which could damage the engine.
If the lack of oil is confirmed by a check using the dipstick, it is essen-tial that the level is topped up.
Lack of oil
Dipstick
There are 2 marks on the dipstick:
- never exceed level A,- in position B, top up the level via the oil filler cap, using the type of oil suited to your engine.
A = max.
B = min.
Trip recorder zero reset button
Lighting rheostat

24
In the event of under-revving or over-revving, the gear selected flashes for a few seconds, then the actual gear engaged is displayed.
This comes on when the "SPORT" programme on the automatic gearbox is selected.
This comes on when the "SNOW" programme on the automatic gearbox is selected.
Automatic gearbox indicator lights
"SNOW" indicator light
This is displayed if a gear is not engaged correctly (selec-tor between two positions).
"SPORT" indicator light
Invalid value during manual operation
After switching on the ignition, three functions are shown in succession:
- service indicator,- engine oil level indicator,- total distance recorder (total and trip distances).Note: the total and trip distances are displayed for 30 seconds when the ignition is switched off, on opening the driver’s door, as well as on lock-ing and unlocking the vehicle.
It also displays the information relat-ing to the cruise control or speed lim-iter, when either of these is activated (see corresponding section).
Service indicator
This indicates when the next service is due in accordance with the manu-facturer’s servicing schedule.
The point at which the next service is due is calculated from the last indi-cator zero reset (see corresponding section). It is determined by two pa-rameters:
- the distance travelled,- the time which has elapsed since the last service.Note: the distance remaining before the next service may be weighted by the time factor, depending on the us-er’s driving habits.
Operation
For 5 seconds after the ignition is switched on, the spanner symbolis-ing the servicing operations comes on; the distance recorder display in-dicates the number of miles [kilome-tres] (rounded off) remaining until the next service.
Example: 4,800 miles/km remain before the next service. For five sec-onds after the ignition is switched on, the display indicates:
INSTRUMENT PANEL
DISPLAY

24
In the event of under-revving or over-revving, the gear selected flashes for a few seconds, then the actual gear engaged is displayed.
This comes on when the "SPORT" programme on the automatic gearbox is selected.
This comes on when the "SNOW" programme on the automatic gearbox is selected.
Automatic gearbox indicator lights
"SNOW" indicator light
This is displayed if a gear is not engaged correctly (selec-tor between two positions).
"SPORT" indicator light
Invalid value during manual operation
After switching on the ignition, three functions are shown in succession:
- service indicator,- engine oil level indicator,- total distance recorder (total and trip distances).Note: the total and trip distances are displayed for 30 seconds when the ignition is switched off, on opening the driver’s door, as well as on lock-ing and unlocking the vehicle.
It also displays the information relat-ing to the cruise control or speed lim-iter, when either of these is activated (see corresponding section).
Service indicator
This indicates when the next service is due in accordance with the manu-facturer’s servicing schedule.
The point at which the next service is due is calculated from the last indi-cator zero reset (see corresponding section). It is determined by two pa-rameters:
- the distance travelled,- the time which has elapsed since the last service.Note: the distance remaining before the next service may be weighted by the time factor, depending on the us-er’s driving habits.
Operation
For 5 seconds after the ignition is switched on, the spanner symbolis-ing the servicing operations comes on; the distance recorder display in-dicates the number of miles [kilome-tres] (rounded off) remaining until the next service.
Example: 4,800 miles/km remain before the next service. For five sec-onds after the ignition is switched on, the display indicates:
INSTRUMENT PANEL
DISPLAY

25
5 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the display indicates the total and trip distance.
Your PEUGEOT dealer carries out this operation after each service.
However, if you carry out the service yourself, the re-set procedure is as follows:
 Switch off the ignition,
 Press and hold the trip recorder re-set button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0", re-lease the button; the spanner disap-pears.
Important: after this operation, if you wish to disconnect the battery, lock the vehicle and wait for at least five minutes, otherwise the zero re-set will not be registered.
The service is overdue.
The spanner flashes for 5 seconds after the ignition is switched on.
Example: the service is overdue by 300 miles/km, your vehicle must be serviced as soon as possible.
For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the spanner remains lit. The display indi-cates the total and trip distance.
Note: the spanner may also come on if more than two years have elapsed since the last service.
The distance remaining to the next service is less than 500 miles (1,000 km).
Example: 400 miles (900 km) remain before the next service.
For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the spanner remains lit.
It indicates that a service must be car-ried out soon. The display indicates the total and trip distance.
Service indicator zero re-set

25
5 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the display indicates the total and trip distance.
Your PEUGEOT dealer carries out this operation after each service.
However, if you carry out the service yourself, the re-set procedure is as follows:
 Switch off the ignition,
 Press and hold the trip recorder re-set button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0", re-lease the button; the spanner disap-pears.
Important: after this operation, if you wish to disconnect the battery, lock the vehicle and wait for at least five minutes, otherwise the zero re-set will not be registered.
The service is overdue.
The spanner flashes for 5 seconds after the ignition is switched on.
Example: the service is overdue by 300 miles/km, your vehicle must be serviced as soon as possible.
For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the spanner remains lit. The display indi-cates the total and trip distance.
Note: the spanner may also come on if more than two years have elapsed since the last service.
The distance remaining to the next service is less than 500 miles (1,000 km).
Example: 400 miles (900 km) remain before the next service.
For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition was switched on, the distance recorder resumes its normal operation and the spanner remains lit.
It indicates that a service must be car-ried out soon. The display indicates the total and trip distance.
Service indicator zero re-set

26
With the lights on, press the button to vary the intensity of the lighting of the instruments and controls. When the lighting reaches the minimum (or maximum) setting, release the button then press it again to increase (or re-duce) the brightness.
As soon as the lighting is of the required brightness, release the button.
With the ignition on, press the button until the zeros appear.
Pressing the button enables you to alternate between the distance recorder and cruise control or speed limiter displays, when either of these is activated.
Engine oil level indicator
When the ignition is switched on, the engine oil level is indicated for a few seconds, after the service information.
Oil level correct
Oil level gauge fault
Flashing of "OIL --" indicates a malfunc-tion of the engine oil level gauge.
Contact a PEUGEOT dealer.
The level read will only be correct if the vehicle is on level ground and the engine has been off for more than 15 minutes.
Flashing of "OIL", linked with the serv-ice warning light, accompanied by an audible signal and a message on the multifunction display, indicates a lack of oil which could damage the engine.
If the lack of oil is confirmed by a check using the dipstick, it is essen-tial that the level is topped up.
Lack of oil
Dipstick
There are 2 marks on the dipstick:
- never exceed level A,- in position B, top up the level via the oil filler cap, using the type of oil suited to your engine.
A = max.
B = min.
Trip recorder zero reset button
Lighting rheostat

27
TRIP COMPUTER
 Press the button, located at the end of the wipers stalk, to display the various items of trip computer data in succession.
The trip computer data is the following:
System which provides current infor-mation concerning the route travelled (range, consumption, ...).
 Press the control for more than two seconds to reset the distance trav-elled, the average consumption and the average speed to zero.
Monochrome screen AZero reset
Data displays
- the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.

28
- the current information tab with:- the range,- the currentconsumption,- the distance remain-ing to be travelled,
Colour screen
Route zero resetMonochrome screen C
 Press the button, located at the end of the wipers stalk, to display the various trip computer tabs in succession:
Data displays
- the route "1" tab with:- the distance travelled,- the averageconsumption,- the average speed,for the first route.
- the route "2" tab with:- the distance travelled,- the average consump-tion,- the average speed,for the second route.
TRIP COMPUTER
System which provides current infor-mation concerning the route travelled (range, consumption, …).
 When the route required is dis-played, press the control for more than two seconds.
Routes "1" and "2" are independent but their use is identical.
Route "1" permits, for example, daily calculations, and route "2" monthly calculations.