Peugeot 307 SW Dag 2007 Owner's Guide

29
Distance remaining to be travelled
(km or miles)
This is the distance remain-ing to be travelled to the final destina-tion. It is either calculated instantly by the navigation system if guidance is activated, or entered by the user.
If the distance is not entered, dashes are displayed in place of the digits.
Average speed
(km/h or mph)
This is the average speed calculated since the last trip computer zero reset (ignition on).
Range
(km or miles)
This indicates the number of miles (or kilometres) which can still be travelled with the fuel remaining in the tank in relation to the average consumption over the last few miles (kilometres) travelled.
Current consumption
(l/100 km or km/l or mpg)
This is the average quantity of fuel consumed over the last few seconds.
Average consumption
(l/100 km or km/l or mpg)
This is the average quan-tity of fuel consumed since the last trip computer zero reset.
Distance travelled
(km or miles)
This indicates the dis-tance travelled since the last trip computer zero reset.
A few definitions…
When the range falls below 20 miles (30 km), dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is displayed when it exceeds 60 miles (100 km).
If dashes are displayed con-tinuously while driving in place of the digits, contact a PEUGEOT dealer.
This function is only displayed from 20 mph (30 km/h).
This figure may increase fol-lowing a change of driving style or relief, resulting in a significant change in the cur-rent consumption.

30
Screen C
 Press the "MENU" button to gain access to the general menu.
 Press the arrows, then the "OK"button to select the "Trip compu-ter" menu.
 On the "Trip computer" menu, select one of the following appli-cations:
Warnings log
This summarises the active warning messages, displaying them in suc-cession on the multifunction display.
Status of the functions
This summarises the active or inac-tive status of the functions present on the vehicle.
Enter the distance to the destination
This enables you to enter an approxi-mate value for the distance to the final destination.
"TRIP COMPUTER" MENU
System which provides general infor-mation concerning the status of cer-tain equipment with which your vehi-cle is equipped, such as the warnings log, the status of the functions...
"DIAGNOSTICS" MENU
 On the "Diagnostics" menu, se-lect one of the following applica-tions:
Colour screen
 Press the "MENU" button to gain access to the general menu.
 Turn the dial and press it to select the "Diagnostics" menu.

31
Presentation
This displays the following informa-tion:
- the time,- the date,- the outside temperature* (this flashes if there is a risk of ice),- the status of the accesses (doors, boot, ...),- the warning messages (e.g.: "Emis-sion control system faulty") or infor-mation messages (e.g.: "Auto lights on"), displayed temporarily, can be cleared by pressing the "ESC" but-ton,- the trip computer (see correspond-ing section).
MONOCHROME DISPLAY A(without RD4 audio equipment)Parameter configuration
There are three display control buttons:
- "ESC" to abandon the operation in progress,- "MENU" to scroll through the menus or sub-menus,- "OK" to select the menu or sub-menu required.Press the "MENU" button to scroll through the various menus of the general menu:
- vehicle configuration,- options,- display settings,- languages,- units.Press the "OK" button to select the menu required.
General menu
* With air conditioning only.

32
Once the "Vehicle configuration" menu has been selected, you can activate or deactivate the following equipment:
- wiper linked with reverse gear (refer to the "Visibility" section),- "follow-me-home" lighting (refer to the "Visibility" section),- parking assistance (refer to the "Driving" section).
Options
Once the "Options" menu has been selected, you can start diagnostics of the status of the equipment (active, not active, faulty).
Languages
Once the "Languages" menu has been selected, you can change the language used by the display (Français, Italiano, Nederlands, Por-tugues, Portugues-Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has been selected, you can gain access to the following settings:
- year,- month,- day,- hour,- minutes,- 12 or 24 hour mode.
Units
Once the "Units" menu has been se-lected, you can change the units of the following parameters:
- temperature (°C or °F),- fuel consumption (l/100, mpg or km/l).
Once you have selected a setting, press the "OK" button to change its value.
Wait for approximately ten sec-onds without any action to allow the changed data to be recorded or press the "ESC" button to cancel.
The display then returns to the nor-mal display.For safety reasons, configu-ration of the multifunction displays by the driver must take place when stationary.
Vehicle configuration

33
MONOCHROME DISPLAY A
Press the "MENU" button to gain ac-cess to the general menu, then press the "" or "" buttons to scroll through the following items:
- radio-CD,- vehicle configuration,- options,- display settings,- languages,- units.Press the "OK" button to select the menu required.
Presentation
This displays the following informa-tion, via the RD4 audio equipment control keypad:
- the time,- the date,- the outside temperature* (this flashes if there is a risk of ice),- the audio source displays (radio, CD, ...),- the status of the accesses (doors, boot, ...),- the warning messages (e.g.: "Emis-sion control system faulty") or infor-mation messages (e.g.: "Auto lights on"), displayed temporarily, can be cleared by pressing the "ESC" but-ton,- the trip computer (see correspond-ing section).
Radio-CD
With the RD4 audio equipment switched on, once the "Radio-CD" menu has been selected, you can activate or deactivate the functions linked with the use of the radio (RDS following, REG mode), the CD or the CD changer (introscan, random play, CD repeat).
For further details concerning the "Radio-CD" application, refer to the RD4 part of the "Audio and Telemat-ics" section.
Once the "Vehicle configuration" menu has been selected, you can activate or deactivate the following equipment:
- rear wiper linked with reverse gear (refer to the "Visibility" section),- "follow-me-home" lighting (refer to the "Visibility" section),- parking assistance (refer to the "Driving" section).
Options
Once the "Options" menu has been selected, you can start diagnostics of the status of the equipment (active, not active, faulty).
General menuVehicle configuration
* With air conditioning only.

34
Display settings
Once the "Display settings" menu has been selected, you can gain access to the following settings:
- year,- month,- day,- hour,- minutes,- 12 or 24 hour mode.
Languages
Once the "Languages" menu has been selected, you can change the language used by the display (Français, Italiano, Nederlands, Por-tugues, Portugues-Brasil, Deutsch, English, Espanol).
Units
Once the "Units" menu has been se-lected, you can change the units of the following parameters:
- temperature (°C or °F),- fuel consumption (l/100, mpg or km/l).
Once you have selected a setting, press the "" or "" buttons to change its value.
Press the "" or "" buttons to move to the previous or next setting respectively.
Press the "OK" button to record the change and return to the normal dis-play or press the "ESC" button to cancel.
For safety reasons, configu-ration of the multifunction displays by the driver must take place when stationary.

35
Presentation
It displays the following information:
- the time,- the date,- the exterior temperature (this flash-es if there is a risk of ice),- the accesses check (doors, boot, ...),- the warning messages (e.g.: "De-pollution system faulty") or infor-mation messages (e.g.: "Automatic headlamp lighting activated"), dis-played temporarily, can be cleared by pressing the "ESC" button,- the trip computer (see correspond-ing section),
MONOCHROME DISPLAY C(without RD4 audio equipment)
There are three buttons and a navi-gator to enable you to control the screen:
- "MENU" to display the general menu, - "MODE" to change the permanent application (trip computer, date, ...),- "ESC" to abandon the operation in progress,- Rotation of the navigator: move-ment on the display or changing of a setting,- Press on the navigator: confirma-tion of the selection.
Press the "MENU" button to access the general menu:
- trip computer (see corresponding section),- personalisation-configuration.
Turn the navigator to select the menu required, then confirm by pressing the navigator.
Once this menu has been selected, you can access the following func-tions:
- define the vehicle parameters,- display configuration,- selection of the language.
Parameter configuration General menu
"Personalisation-Configuration" menu

36
Selection of the language
Once this menu has been selected, you can change the language used on the display (Deutsch, English, Espanol, Français, Italiano, Neder-lands, Portugues, Portugues-Brasil).
Display configuration
Once this menu has been selected, you can access the following set-tings:
- brightness-video setting,- date and time setting,- selection of the units.
Example: "Duration of the "follow-me-home" lighting"
For safety reasons, configu-ration of the multifunction displays by the driver must take place when stationary.
Define the vehicle parameters
Once this menu has been selected, you can activate or deactivate the fol-lowing equipment:
- wiper linked with reverse gear (re-fer to the "Visibility" section),- "follow-me-home" lighting and du-ration (refer to the "Visibility" sec-tion),- parking assistance (refer to the "Driving" section).
Once you have selected a setting, press the navigator.
Turn the navigator to change its value.
Press the navigator to record the change and move on to the next set-ting or press the "ESC" button to cancel.

37
MONOCHROME SCREEN C
Controls
From the RD4 audio equipment con-trol panel, you can: press the "MENU" button to gain access to the general menu,
 press the "" or "" buttons to scroll through the items on the screen,
 press the "MODE" button to change the permanent application (trip computer, audio source, ...),
 press the "" or "" buttons to change a setting value,
 press the "OK" button to confirm,or
 press the "ESC" button to aban-don the operation in progress.
Displays on the screen
This displays the following information:
- the time,- the date,- the outside temperature* (this flashes if there is a risk of ice),- the status of the accesses (doors, boot, ...),- the audio sources (radio, CD, ...),- the trip computer (refer to the cor-responding section).Warning messages (e.g.: "Emission control system faulty") or information messages (e.g.: "Automatic switch-ing on of the headlamps activated") may appear temporarily. These can be cleared by pressing the "ESC"button.
General menu
Press the "MENU" button to gain access to the general menu:
- audio functions,- trip computer (refer to the corre-sponding section),- personalisation-configuration,- telephone (hands-free kit).
 Press the "" or "" buttons to select the menu required, then confirm by pressing the "OK" but-ton.
* With air conditioning only.
"Audio functions" menu
With the RD4 audio equipment switched on, once this menu has been selected you can activate or de-activate the functions linked with use of the radio (RDS, REG, RadioText), the CD or the CD changer (introscan, shuffle, CD repeat).
For further details concerning the "Audio functions" application, refer to the RD4 part of the "Audio and Telematics" section.
"Trip computer" menu
Once this menu has been selected, you can consult information concern-ing the status of the vehicle (warn-ings log, status of the functions, ...).

38
"Personalisation-Configuration" menu
Once this menu has been selected, you can gain access to the following functions:
- define the vehicle parameters,- display configuration,- selection of the language.
Display configuration
Once this menu has been selected, you can gain access to the following settings:
- brightness-video setting,- date and time setting,- selection of the units.
Example: setting of the duration of the "follow-me-home" lighting
 Press the "" or "" buttons, then the "OK" button to select the menu required.
 Press the "" or "" buttons, then the "OK" button to select the "Lighting and signalling" line.
 Press the "" or "" buttons to set the value required (15, 30 or 60 seconds), then press the "OK"button to confirm.
For safety reasons, it is im-perative that configuration of the multifunction displays by the driver takes place when stationary.
Define the vehicle parameters
Once this menu has been selected, you can activate or deactivate the fol-lowing equipment:
- wiper linked with reverse gear (re-fer to the "Visibility" section),- "follow-me-home" lighting (refer to the "Visibility" section),- parking assistance (refer to the "Driving" section).
 Press the "" or "" buttons, then the "OK" button to select the "OK" box and confirm or press the "ESC" button to cancel.
Selection of the language
Once this menu has been selected, you can change the language used by the display (Deutsch, English, Espanol, Français, Italiano, Neder-lands, Portugues, Portugues-Brasil).
"Telephone" menu
With the RD4 audio equipment switched on, once this menu has been selected you can configure your Bluetooth hands-free kit (match-ing), consult the various telephone directories (calls log, services, ...) and manage your communications (pick up, hang up, call waiting, secret mode, ...).
For further details concerning the "Telephone" application, refer to the RD4 part of the "Audio and Telemat-ics" section.