boot PEUGEOT 308 2010 Owner's Guide

Page 161 of 315

135
Emergency release
For safety reasons, after this
manoeuvre it is essential to
contact a PEUGEOT dealer
urgently to replace the protective
cover.
Following an emergency unlocking,
immobilisation of the vehicle is no
longer guaranteed once the manual
emergency release has been de-
ployed and the manual control does
not allow the re-application of your
parking brake.
Take no action, either on control A , or
stopping starting the engine while the
release device is engaged.
Take care not to allow moisture or
dust in the proximity of the protective
cover.

 Immobilise the vehicle (or keep
it stationary, if the brake pedal is
pressed), with the engine running,
by engaging fi rst gear (manual gear-
box), position P (automatic gearbox)
or M or R (6-speed electronic gear
control gearbox).

 Switch off the engine but leave the
ignition on. If it is impossible to im-
mobilise the vehicle, do not action
the control and urgently contact a
PEUGEOT dealer.

 Fetch the two vehicle blocks and
the release device, located under
the boot carpet (see "Changing a
wheel" in the "Practical information"
section).

 Immobilise the vehicle by placing
blocks at the front and at the rear of
one of the rear wheels.

 Slide the front left-hand seat back
as far as possible.

 Lift up the fl oor plug B in the carpet
under the seat.

 Pierce the protective cover C on the
tube D with the release device.

 Place the release device in the tube D .

 Turn the release device clockwise.


For safety reasons , it is essential
to continue turning the device as
far as it will go or until you hear a
knocking noise. The parking brake
is released.
 Remove the release device and store
it with the blocks in the toolbox.
- The operation of the parking brake reinitialises when the igni-
tion is switched off then on again.
If the reinitialisation of the parking
brake proves impossible, contact a
PEUGEOT dealer.
- The subsequent time required for application may be longer than
during normal operation.

Front left seat moved back fully.
In the event of the electric parking brake
malfunctioning or the battery running
fl at, an emergency manual device can
release the parking brake.

Page 189 of 315

PRACTICAL INFORMATION
165
TEMPORARY PUNCTURE REPAIR KIT
The kit is located in the boot under the
fl oor. It is installed in the tool box, lo-
cated under the storage box.
Complete system consisting of a com-
pressor and an incorporated sealant
cartridge which permits
temporary
repair of the tyre so that you can drive
to the nearest garage.
All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.

1. 12 V compressor.
Contains a sealant for temporary repair of the tyre and permits ad-
justment of the tyre pressure.

2. Two chocks to chock the vehicle.

3. Socket for security bolts (located
in the glove compartment).
Permits adaptation to the special security bolts.
List of tools
Other accessories

4. Removable towing eye.
Refer to "Electric parking
brake" in the "Driving" section.
Refer to the paragraph "Towing
the vehicle".

5. Electric parking brake emergency
release control.
Access to the kit

Page 193 of 315

PRACTICAL INFORMATION
169
CHANGING A WHEEL
The tools are installed in the boot under
the fl oor.
To gain access to them:

 open the boot,

 place the adjustable boot fl oor at
an angle (refer to the "Fittings" sec-
tion),

 raise the fl oor,

 secure it by hooking its cord on the
hook on the rear parcel shelf support,

 remove the polystyrene storage box,

 unclip by pulling upwards then re-
move the box containing the tools.
Access to the tools
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.

 To make the operation easier, re-
move the adjustable boot fl oor,

 unscrew the yellow central bolt,
With the JBL bass unit

 remove the bass unit disconnecting
the electrical harness,

 remove the polystyrene storage box.

Page 194 of 315

PRACTICAL INFORMATION
169
CHANGING A WHEEL
The tools are installed in the boot under
the fl oor.
To gain access to them:

 open the boot,

 place the adjustable boot fl oor at
an angle (refer to the "Fittings" sec-
tion),

 raise the fl oor,

 secure it by hooking its cord on the
hook on the rear parcel shelf support,

 remove the polystyrene storage box,

 unclip by pulling upwards then re-
move the box containing the tools.
Access to the tools
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.

 To make the operation easier, re-
move the adjustable boot fl oor,

 unscrew the yellow central bolt,
With the JBL bass unit

 remove the bass unit disconnecting
the electrical harness,

 remove the polystyrene storage box.

Page 196 of 315

PRACTICAL INFORMATION
Access to the spare wheel
The spare wheel is installed in the boot
under the fl oor.
According to country, the spare wheel
may be steel, alloy or of the "space-
saver" type.
To gain access to it, refer to the para-
graph "Access to the tools" on the previ-
ous page. Taking out the wheel

 Unscrew the yellow central bolt.

 Raise the spare wheel towards you
from the rear.

 Take the wheel out of the boot.
Putting the wheel back in place

 Put the wheel back in its housing.

 Unscrew the yellow central bolt by a
few turns then put it in place in the
centre of the wheel.

 Tighten fully until the central bolt
clicks to retain the wheel correctly.

 Put the box back in place in the cen-
tre of the wheel and clip it.

 Put the polystyrene storage box
back in place.
Tyre under-infl ation detection
The spare wheel is not fi t-
ted with a sensor. The punc-
tured wheel must be repaired by a
PEUGEOT dealer.

Page 203 of 315

PRACTICAL INFORMATION
178
Changing the third brake lamp bulb Changing the number plate lamp
bulbs (W5-5W)

 Insert a thin screwdriver into one of
the outer holes of the lens.

 Push it outwards to unclip.

 Remove the lens.

 Pull the bulb and change it.
Changing sidelamp bulbs (boot)
Changing foglamp bulbs

 Open the boot.

 Remove the plastic fl ap using a
screwdriver.

 Remove the lamp fi xing nut.

 Turn the bulb a quarter of a turn and
change it.
To refi t, carry out these operations in
reverse order.

 Reach under the bumper.

 Turn the bulb a quarter of a turn and
change it.
 Open the boot and remove the up-
per seal.

 Unscrew the two nuts.

 Press the threaded pins while sup-
porting the lamp from the outside.

 Disconnect the connector and
remove the screenwash pipe.

 Press the pairs of clips A then B
then C to detach and gain access to
the bulb holder.

Page 215 of 315

PRACTICAL INFORMATION
190
TOWING THE VEHICLE
Access to the tools Towing your vehicle

 On the front bumper, unclip the co-
ver by pressing at the bottom.

 Screw the towing eye in fully.

 Install the towing bar.

 Switch on the hazard warning lamps
on the towed vehicle.
 On the rear bumper, unclip the cover
by pressing at the bottom.

 Screw the towing eye in fully.

 Install the towing bar.

 Switch on the hazard warning lamps
on the towed vehicle.
Towing another vehicle
The towing eye is installed in the boot
under the fl oor.
To gain access to it:

 open the boot,

 raise the fl oor,

 secure it by hooking the cords on
the hooks on the rear parcel shelf
support,

 remove the polystyrene box,

 remove the towing eye from the
holder. When towing with all four
wheels on the ground, always
use a towing bar.
When towing with only two wheels on
the ground, always use professional
lifting equipment.
When towing with the engine off,
there is no longer any braking or
steering assistance.

 Place the gear lever in neu-
tral (position N on the elec-
tronic gear control gearbox
or automatic gearbox).
Failure to observe this spe- cial condition could result
in damage to certain bra-
king components and the
absence of braking assis-
tance the next time the en-
gine is started.
Procedure for having your vehicle towed
or for towing another vehicle using a
removable towing eye.

Page:   < prev 1-10 11-20 21-30 31-40