ESP PEUGEOT 308 2010 Service Manual
Page 182 of 315
CHECKS
159
RUNNING OUT OF FUEL (DIESEL)
I f y o u r v e h i c l e i s fi t t e d w i t h a n H D I e n -
gine, the fuel system must be primed if
you run out of fuel.
This system consists of a priming pump
and, according to engine (see graphic
and explanations below), a transparent
pipe and a bleed screw under the bonnet
(refer to the corresponding graphic). 1.6 litre Turbo HDI 16V engine
F i l l t h e f u e l t a n k w i t h a t l e a s t fi v e l i t r e s
of diesel.
Open the bonnet.
Operate the priming pump until it
hardens.
Operate the starter until the engine
starts.
Close the bonnet. 2 litre Turbo HDI 16V engine
F i l l t h e f u e l t a n k w i t h a t l e a s t fi v e l i -
tres of diesel.
Open the bonnet.
Unclip the style cover for access to
the priming pump.
Slacken the bleed screw.
Squeeze and release the priming
pump until fuel appears in the trans-
parent pipe with the green connector.
Retighten the bleed screw.
Operate the starter until the engine
starts.
Put the style cover back in position
and clip it in place.
Close the bonnet.
If the engine does not start
a t t h e fi r s t a t t e m p t , d o n o t t r y
again.
Operate the priming pump again,
then the starter. If the engine does not start
a t t h e fi r s t a t t e m p t , d o n o t t r y
again.
Operate the priming pump again,
then the starter.
Page 185 of 315
CHECKS
162
CHECKING LEVELS
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
I f a l e v e l d r o p s s i g n i fi c a n t l y , h a v e t h e
corresponding system checked by a
PEUGEOT dealer. Brake fluid level
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.
Oil level The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
The check is carried out either when the
ignition is switched on using the oil level
indicator on the instrument panel, or us-
ing the dipstick. T h e b r a k e fl u i d l e v e l s h o u l d b e
close to the "MAX" mark. If it is
not, check the brake pad wear.
C h a n g i n g t h e fl u i d
Refer to the Warranty and Maintenance
Record for details of the interval for this
operation.
Power steering fluid level T h e p o w e r s t e e r i n g fl u i d l e v e l
should be close to the "MAX"
mark. Unscrew the cap, with
the engine cold, to check the
level. Screenwash and headlamp
wash fluid
I n t h e c a s e o f v e h i c l e s fi t t e d w i t h
headlamp washers, the minimum
l e v e l o f t h i s fl u i d i s i n d i c a t e d b y a n
audible signal and a message on
the multifunction screen.
Top up the level when you stop the vehicle. Engine oil change
Refer to the Warranty and Maintenance
Record for details of the interval for this
operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.
O i l s p e c i fi c a t i o n
The oil must correspond to your engine
and conform to the manufacturer's recom-
mendations. F l u i d s p e c i fi c a t i o n
T h e b r a k e fl u i d m u s t c o n f o r m t o t h e
manufacturer's recommendations and
f u l fi l t h e D O T 4 s t a n d a r d s .
Changing the coolant
The coolant does not have to be
changed.
F l u i d s p e c i fi c a t i o n
For optimum cleaning and to avoid
f r e e z i n g , t h i s fl u i d m u s t n o t b e t o p p e d
up with or replaced with water.
Coolant level
The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm, the tempera-
ture of the coolant is regulated by the fan.
This can operate with the ignition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h a
p a r t i c l e e m i s s i o n fi l t e r , t h e f a n m a y
operate after the vehicle has been
s w i t c h e d o f f , e v e n i f t h e e n g i n e i s
cold. F l u i d s p e c i fi c a t i o n
The coolant must conform to the manu-
facturer's recommendations.
When working under the bon-
net, take care, as certain areas
of the engine may be extremely
hot (risk of burns).
Page 204 of 315
PRACTICAL INFORMATION
179
CHANGING A FUSE
Procedure for replacing a faulty fuse
with a new fuse to rectify a failure of the
c o r r e s p o n d i n g f u n c t i o n .
Access to the tools
T h e e x t r a c t i o n p l i e r s a n d t h e s p a r e f u s -
e s a r e i n s t a l l e d o n t h e b a c k o f t h e d a s h -
b o a r d f u s e b o x c o v e r .
T o g a i n a c c e s s t o t h e m :
r e m o v e t h e c o v e r c o m p l e t e l y ,
r e m o v e t h e p l i e r s . Changing a fuse
B e f o r e c h a n g i n g a f u s e , t h e c a u s e o f
t h e f a i l u r e m u s t b e i d e n t i fi e d a n d r e c t i -
fi e d .
I d e n t i f y t h e f a u l t y f u s e b y c h e c k i n g
t h e c o n d i t i o n o f i t s fi l a m e n t .
Correct Incorrect
U s e t h e s p e c i a l p l i e r s t o e x t r a c t t h e
f u s e f r o m i t s h o u s i n g .
Always replace the faulty fuse with a
f u s e o f t h e s a m e r a t i n g .
Check the correspondence between
t h e n u m b e r e t c h e d o n t h e b o x , t h e
rating etched on the fuse and the
t a b l e s b e l o w . Installing electrical
accessories
Your vehicle's electrical system
is designed to operate with standard
o r o p t i o n a l e q u i p m e n t .
Before installing other electrical
equipment or accessories on your
v e h i c l e , c o n t a c t a P E U G E O T d e a l e r .
P E U G E O T w i l l n o t a c c e p t r e -
sponsibility for the cost incurred
in repairing your vehicle or for
r e c t i f y i n g m a l f u n c t i o n s r e s u l t -
ing from the installation of accessories
not supplied and not recommended by
P E U G E O T a n d n o t i n s t a l l e d i n a c c o r -
d a n c e w i t h i t s i n s t r u c t i o n s , i n p a r t i c u l a r
when the combined consumption of all
of the additional equipment connected
e x c e e d s 1 0 m i l l i a m p e r e s .
Page 208 of 315
PRACTICAL INFORMATION
183
Engine compartment fuses
T h e f u s e b o x i s p l a c e d i n t h e e n g i n e
c o m p a r t m e n t n e a r t h e b a t t e r y ( l e f t - h a n d
s i d e ) .
Access to the fuses
U n c l i p t h e c o v e r .
Change the fuse (see corresponding
p a r a g r a p h ) .
W h e n y o u h a v e fi n i s h e d , c l o s e t h e
cover carefully to ensure correct
s e a l i n g o f t h e f u s e b o x . Fuse table
Fuse
N° Rating
(A)
Functions
F1 20 E n g i n e c o n t r o l u n i t s u p p l y , i n j e c t i o n p u m p a n d E G R
e l e c t r o v a l v e s ( 2 l H D I 1 6 V ) , i n j e c t o r s ( 2 l H D I 1 6 V ) .
F2 15 H o r n .
F3 10 F r o n t / r e a r w a s h - w i p e .
F4 10 D a y t i m e r u n n i n g l a m p s .
F5 15 P u r g e c a n i s t e r , t u r b i n e d i s c h a r g e a n d T u r b o
p r e s s u r e r e g u l a t i o n e l e c t r o v a l v e s ( 1 . 6 l T H P 1 6 V ) ,
o i l v a p o u r h e a t e r ( 1 . 6 l T H P 1 6 V ) , d i e s e l h e a t e r
( 1 . 6 l H D I 1 6 V ) .
F6 10 D i a g n o s t i c s o c k e t , d i r e c t i o n a l h e a d l a m p s , p a r t i c l e
e m i s s i o n fi l t e r p u m p ( D i e s e l ) , D i s t a n c e a l e r t ,
e n g i n e c o o l a n t l e v e l d e t e c t o r , m i r r o r a d j u s t m e n t
c o n t r o l .
F7 10 P o w e r s t e e r i n g c o n t r o l u n i t , a u t o m a t i c g e a r b o x ,
d i r e c t i o n a l h e a d l a m p s h e i g h t a d j u s t m e n t m o t o r .
F8 20 S t a r t e r m o t o r c o n t r o l .
F9 10 C l u t c h a n d b r a k e p e d a l s w i t c h e s .
F10 30 E n g i n e c o n t r o l u n i t a c t u a t o r s ( p e t r o l : i g n i t i o n c o i l s ,
e l e c t r o v a l v e s , o x y g e n s e n s o r s , i n j e c t o r s , h e a t e r s ,
f u e l p u m p , e l e c t r o n i c t h e r m o s t a t )
( D i e s e l : e l e c t r o v a l v e s , h e a t e r s ) .
F11 40 A i r c o n d i t i o n i n g b l o w e r .
Page 214 of 315
PRACTICAL INFORMATION
189
CHANGING A WIPER BLADE
Removing
R a i s e t h e c o r r e s p o n d i n g w i p e r a r m .
U n c l i p t h e w i p e r b l a d e a n d r e m o v e i t . Fitting
Put the corresponding new wiper
b l a d e i n p l a c e a n d c l i p i t .
F o l d d o w n t h e w i p e r a r m c a r e f u l l y .
Before removing a front wiper
blade
Within one minute after switching off
t h e i g n i t i o n , o p e r a t e t h e w i p e r s t a l k
t o p o s i t i o n t h e w i p e r b l a d e s v e r t i -
c a l l y o n t h e w i n d s c r e e n . After fitting a front wiper blade
S w i t c h o n t h e i g n i t i o n .
Operate the wiper stalk again to
p a r k t h e w i p e r b l a d e s .
Page 239 of 315
214
7
8
1 0
9
1 1
0 4
Repeat steps 5 to 7 for the "Street" and "House number" functions.
T o d e l e t e a d e s t i n a t i o n ; f r o m s t e p s 1 t o 3 , s e l e c t " C h o o s e f r o m l a s t T o d e l e t e a d e s t i n a t i o n ; f r o m s t e p s 1 t o 3 , s e l e c t " C h o o s e f r o m l a s t destinations". A long press on one of the destinations displays a list o list of actions from w h i c h y o u c a n s e l e c t :
Select the "Save to address book" function to record thord the address e n t e r e d i n a d i r e c t o r y fi l e . P r e s s O K t o c o n fi r m t h e s e l e c t i o n . e n t e r e d i n a d i r e c t o r y fi l e . P r e s s O K t o c o n fi r m t h e s e l e c t i o n . The Peugeot Connect Media permits the recording of mg of more than 4 0 0 0 c o n t a c t fi l e s .
To speed up the process, the post code can be enteredtered directly after selecting the "Postal code" function. Use the virtual keypad to enter the letters and digits. S e l e c t t h e r o u t e t y p e : "Fast route", "Short route", or " O p t i m i z e d r o u t e " a n d p r e s s O K t o c o n fi r m .
Then select "Start route guidance" a n d t h e p r e s s O K t o c o n fi r m .
It is also possible to select a destination via "Choose frose from address book" or "Choose from last destinations", by select ing ating a junction, a town centre, geographic coordinates, or directly on the on the "Map".
CHOOSE FROM ADDRESS BOOK CHOOSE FROM LAST DST DESTINATIONS
START ROUTE GUIDANCE
It is possible to scroll the map using the 4-direction navigator. It is possible to select its orientation via the short-cut menu of the "Full scr een map". Press OK then select " M a p S e t t i n g s " a n d c o n fi r m .
Select the road with the colour corresponding to the route chosen a n d p r e s s O K t o c o n fi r m a n d s t a r t guidance.
Turn the ring and select OK. P r e s s O K t o c o n fi r m .
DELETE ENTRY DELETE LISTE LIST
N A V I G A T I O N - G U I D A N C E
Page 248 of 315
223
RADIO
1 1
2
3
0 6
SELECTING A STATION
When the current radio station is displayed on the screen, press OK.
The radio source short-cuts menu appears and providesovides access to t h e f o l l o w i n g s h o r t - c u t s :
Select the function required and press O K t o c o n fi r m t o g a i n a c c e s s t o t h e corresponding settings.
TA
The RDS, if displayed, allows you to continue listening tning to the same station by automatic retuning to alternative freque ncies.ncies. However, in certain conditions, coverage of an RDS station may not y not be assured throughout the country as radio stations do not cover 10ver 100 % of the territory. This explains the loss of reception of the stationstation during a journey.
T h e e x t e r n a l e n v i r o n m e n t ( h i l l , b u i l d i n g , t u n n e l , u n d e r g r o u n d c a r p a r k . . . ) m a y i n t e r f e r e w i t h the reception, including in RDS following mode. Thi s phenomenon is a normal result of the way in which radio waves are transmitted and does n ot in any way indicate a failure of the audio equipment.
R D S - R E G I O N A L M O D E
Press the RADIO button to display the list of stations received locally sorted in alphabetical order. Select the station required by turning t h e r i n g a n d p r e s s t o c o n fi r m .
Press one of the buttons on the numeric keypad fo r moor more than 2 s e c o n d s t o s t o r e t h e c u r r e n t s t a t i o n . A b l e e p c o n fi r m s t h a t i t h a s 2 s e c o n d s t o s t o r e t h e c u r r e n t s t a t i o n . A b l e e p c o n fi r m s t h a t i t h a s been stored. Press the button on the numeric keypad to recall the stothe stored radio station.
RDS
RADIOTEXT
R E G I O N A L P R O G .
AM
RADIO
When the "RADIO" screen is displayed, turn the ring or use the 4-direction navigator to select the previous or next station on the list.
While listening to the radio, press buttons and for the automatic search for a lower or higher frequency.
Page 262 of 315
237
SETUP
1
2
3
4
3
4
2
3
3
3
3
2
3
4
4
4
4
2
4
3
2
4
4
3
4
4
3
3
3
4
4
4
4
4
4
4
4
3
4
4
5
5
5
4
5
5
3
"SETUP" MENU
LANGUAGE & SPEECH
M e n u l a n g u a g e
Deutsch
English
Español
Français
Italiano
Nederlands
Polski
Portuguese
V o i c e c o n t r o l
Voice control active
Tutorial
Basics
Examples
Tips
Speaker adaptation
New speaker adaptation
Delete speaker adaptation
V o i c e o u t p u t v o l u m e
DATE & TIME
S e t d a t e & t i m e
D a t e f o r m a t
T i m e f o r m a t
DISPLAY
B r i g h t n e s s
C o l o u r
Steel
B l u e l i g h t ( o n l y i n d a y m o d e )
Orange Ray
Blue Flame
MAP c o l o u r
Day mode for MAP
Night mode for MAP
A u t o . D a y / N i g h t f o r MAP
UNITS
T e m p e r a t u r e
Celsius
Fahrenheit
M e t r i c / I m p e r i a l
km
Miles
SYSTEM
F a c t o r y r e s e t
S o f t w a r e v e r s i o n
A u t o m a t i c s c r o l l i n g
Page 282 of 315
257
3
2
1
1
0 6
When the current radio station is displayed on the screen, press the dial.
T h e r a d i o s o u r c e s h o r t - c u t s m e n u a p p e a r s a n d p r o v
i d e s a c c e s s t o T h e r a d i o s o u r c e s h o r t - c u t s m e n u a p p e a r s a n d p r o v i d e s a c c e s s t o the following short-cuts:
Select the function required and press t h e d i a l t o c o n fi r m t o g a i n a c c e s s t o the corresponding settings.
T A
R D S , i f d i s p l a y e d , a l l o w s y o u t o c o n t i n u e l i s t e n i n g t o t h e s a m e R D S , i f d i s p l a y e d , a l l o w s y o u t o c o n t i n u e l i s t e n i n g t o t h e s a m e s t a t i o n b y a u t o m a t i c r e t u n i n g t o a l t e r n a t i v e f r e q u e n c i e s . H o w e v e r , i n s t a t i o n b y a u t o m a t i c r e t u n i n g t o a l t e r n a t i v e f r e q u e n c i e s . H o w e v e r , i n c e r t a i n c o n d i t i o n s , c o v e r a g e o f a n R D S s t a t i o n m a y n o t b e a s s u r e d c e r t a i n c o n d i t i o n s , c o v e r a g e o f a n R D S s t a t i o n m a y n o t b e a s s u r e d throughout the entire country as radio stations do not conot cover 100 % of the territory. This explains the loss of reception of the stathe station during a j o u r n e y .
T h e e x t e r n a l e n v i r o n m e n t ( h i l l , b u i l d i n g , t u n n e l , u n d e r g r o u n d c a r p a r k . . . ) m a y i n t e r f e r e w i t h t h e r e c e p t i o n , i n c l u d i n g i n R D S f o l l o w i n g m o d e . T h i s p h e n o m e n o n i s a n o r m a l r e s u l t o f t h e w a y i n w h i c h r a d i o w a v e s a r e t r a n s m i t t e d a n d d o e s n o t i n a n y w a y i n d i c a t e a f a i l u r e o f t h e a u d i o e q u i p m e n t .
R D S - R E G I O N A L M O D E
Press the RADIO button to display the list of stations received locally sorted in alphabetical order. Select the station required by turning t h e d i a l a n d p r e s s t o c o n fi r m .
While listening to the radio, press one of the buttons to select the previous or next station on the list.
P r e s s o n e o f t h e b u t t o n s o n t h e n u m e r i c k e y p a d f o r m o r e t h a n P r e s s o n e o f t h e b u t t o n s o n t h e n u m e r i c k e y p a d f o r m o r e t h a n 2 seconds to store the current station. P r e s s t h e b u t t o n o n t h e n u m e r i c k e y p a d t o r e c a l l t h e s t o r e d r a d i o P r e s s t h e b u t t o n o n t h e n u m e r i c k e y p a d t o r e c a l l t h e s t o r e d r a d i o station.
R D S
R A D I O T E X T
R E G I O N A L P R O G .
A M
R A D I O
A long press of one of the buttons starts the a u t o m a t i c s e a r c h f o r a s t a t i o n w i t h a l o w e r o r higher frequency.
Page 285 of 315
260
4 3
1
2
0 7
1
4
2
3
5
M U S I C M E D I A P L A Y E R S
C o n n e c t t h e p o r t a b l e e q u i p m e n t ( M P 3 / W M A p l a y e r … ) t o t h e J A C K audio socket or to the USB port, using a suitable audio cable.
Press the MUSIC button then press it again or select the Music Menu f u n c t i o n a n d p r e s s t h e d i a l t o c o n fi r m .
S e l e c t t h e A U X m u s i c s o u r c e a n d p r e s s t h e d i a l t o c o n fi r m . P l a y b e g i n s a u t o m a t i c a l l y .
Select the "External device" function and press the dial to activate it.
E X T E R N A L D E V I C E
T h e d i s p l a y a n d m a n a g e m e n t o f t h e c o n t r o l s i s v i a
t h e p o r t a b l e T h e d i s p l a y a n d m a n a g e m e n t o f t h e c o n t r o l s i s v i a t h e p o r t a b l e e q u i p m e n t .
U S I N G T H E E X T E R N A L I N P U T ( A U X )
J A C K / U S B A U D I O C A B L E N O T S U P P L I E D
M U S I C M E N U
C D C H A N G E R
S E L E C T M U S I C
M U S I C M E N U
I n s e r t o n e o r m o r e C D s i n t h e changer. Press the MUSIC button.
Press one of the buttons on the n u m e r i c k e y p a d t o s e l e c t t h e corresponding CD.
S e l e c t t h e " C D C h a n g e r " m u s i c s o u r c e a n d p r e s s t h e d i a l t o c o n fi r m .
S e l e c t t h e " S e l e c t m u s i c " f u n c t i o n a n d p r e s s t h e d i a l t o c o n fi r m .
Press the MUSIC button again or select the Music Menu function and p r e s s t h e d i a l t o c o n fi r m .
C D C H A N G E R
P L A Y I N G A C D ( N O T M P 3 / W M A C O M P A T I B L E )