display Peugeot 308 CC 2008.5 Owner's Manual

!
!i
i
FAMILIARISATION
OPEN
Retractable roof operations
Opening the roof
 Pull this control until the roof
opening operation is com-
plete.
Closing the roof

 Press this control until the roof
closing operation is complete.

Change to "cabriolet" confi guration:
- the four windows lower partially,
- the boot opens,
- the roof folds into the boot,
- the boot closes.

Change to "coupé" confi guration:
- the four windows lower partially,
- the boot opens,
- the roof unfolds and locks automati- cally,
- the boot closes.
To ensure that the roof operates
correctly, do not release the control
while the roof is moving.
However, in the event of any danger,
release the control, the roof stops;
then, once the danger had been
eliminated, complete the movement
required. Operating fault
If a malfunction of the roof occurs,
apply the handbrake, switch off
the ignition, start the engine again,
then start the operation required
again.
If the problem persists, contact a
PEUGEOT dealer.
The electric window controls and
the control for all four windows are
deactivated while the roof is in op-
eration.
The end of the manoeuvre is confi rmed
by an audible signal and a message on
the multifunction display.
The end of the manoeuvre is confi rmed
by an audible signal and a message on
the multifunction display.
If you continue to pull or press this
control after the end of the ma-
noeuvre, the four windows rise.

FAMILIARISATION
INSTRUMENTS AND CONTROLS

1. Steering wheel adjustment control.

2. Cruise control/speed limiter
switches.

3. Lights and direction indicators
controls.

4. Central adjustable and closing
vents.

5. Multifunction display.

6. Sunshine sensor.

7. Passenger air bag.

8. Glove box/Audio/video sockets/
Fuse box.

9. Bonnet release.

10. Retractable roof control.
Control for all four windows.

11. Storage compartment or instrument
panel navigator associated with the
WIP Com 3D.

12. "AIRWAVE" system controls.

13. Front armrest.

14. Front ashtray.

15. Heating/air conditioning controls.

16. Audio and telematics system.

17. Emergency call button.
Alarm button.
Central locking button.
Hazard warning lights button.
Dynamic stability control (ESP/ASR) button.
Parking assistance button.
PEUGEOT services button.

FAMILIARISATION
MONITOR THOROUGHLY
Instrument panel Controls bar

A. With the ignition on, the needle should
indicate the level of fuel remaining.

B. With the engine running, its asso-
ciated low level warning light should
switch off.

C. With the ignition on, the oil level in-
dicator should display "OIL OK" for
a few seconds.
If the levels are not correct, top up the
levels which are low. Lighting of the indicator light indicates
the status of the corresponding function.

A. Emergency call in progress.

B. Disarming of the interior protection
alarm.


 68

C. Central locking.


 73

D. Deactivation of the ESP/ASR system.


 95

E. Deactivation of the visual and audible
parking assistance.


 119

F. Access to the PEUGEOT services.
For A and F , refer to the specifi c user
guide given to you with the other owner's
documents.

1. With the ignition on, the orange and
red warning lights come on.

2. With the engine running, these war-
ning lights should switch off.
If warning lights remain on, refer to the
page concerned.
Warning lights


 19

 23

FAMILIARISATION
DRIVE SAFELY
Speed limiter "LIMIT" Display on the instrument panel

1. Limiter mode Selection/Off.

2. Decreasing of the programmed value.

3. Increasing of the programmed value.

4. Speed limiter On/Off.
The values must be set with the engine
running. The cruise control or speed limiter mode
appears on the instrument panel when
it is selected.

1. Cruise control mode Selection/Off.

2. Programming a speed/Decreasing
of the programmed value.

3. Programming a speed/Increasing of
the programmed value.

4. Cruise control Off/Resume.
Cruise control "CRUISE"
Cruise control
Speed limiter


 117


 115
In order to be programmed or activated,
the vehicle speed must be higher than
25 mph (40 km/h), with at least fourth
gear engaged on the manual gearbox
(second gear for the automatic gear-
box).

1
i
19
INSTRUMENTS and CONTROLS
PETROL - DIESEL MANUAL GEARBOX INSTRUMENT PANELS
Panel grouping together the vehicle
operation indication dials and warning
lights.
5. Display.

6. Display zero reset button.
Resets the selected function to zero (trip distance recorder or service
indicator).

7. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Coolant temperature.
Indicates the temperature of the engine coolant (°Celsius).

3. Fuel level.
Indicates the quantity of fuel remaining in the tank.

4. Vehicle speed.
Indicates the current speed of the moving vehicle (km/h or mph).
A. Speed limiter
or
Cruise control.
(km/h or mph)

B. Trip distance recorder.
(km or miles)
The following three functions are displayed in succession when the
ignition is switched on.

C. Service indicator.
(km or miles) then,
Engine oil level indicator.
then
Distance recorder.
(km or miles)
Display
For further information, refer to the
paragraph relating to the button or
function and its associated display.

1
i
20
INSTRUMENTS and CONTROLS
PETROL - DIESEL MANUAL OR AUTOMATIC GEARBOX INSTRUMENT PANELS
Panel grouping together the vehicle
operation indication dials and warning
lights.
5. Small display.

6. Large display.

7. CHECK/display zero reset button.
Starts a manual CHECK.
Resets the function selected to zero (trip distance recorder or service
indicator).

8. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Coolant temperature.
Indicates the temperature of the engine coolant (°Celsius).

3. Fuel level.
Indicates the quantity of fuel remaining in the tank.

4. Vehicle speed.
Indicates the current speed of the moving vehicle (km/h or mph).
A. Trip distance recorder.
(km or miles)

B. Distance recorder.
(km or miles)
The following two functions are displayed in succession when the
ignition is switched on.

C. Service indicator.
(km or miles) then,
Engine oil level indicator.
Displays
For further information, refer to the
paragraph which relates to the but-
ton or function and its associated
display. The following functions are displayed in
accordance with the selection.
-
Warning lights/CHECK.
- Tyre under-infl ation detection.
- Speed limiter/Cruise control.
- Automatic gearbox.
- Navigation - Guidance/Trip computer
information.

1
i
21
INSTRUMENTS and CONTROLS
PETROL - DIESEL MANUAL OR AUTOMATIC GEARBOX WIP COM 3D INSTRUMENT PANELS
Panel grouping together the vehicle
operation indication dials and warning
lights.
5. Small display.

6. WIP Com 3D 16/9 large display.

7. CHECK/display zero reset button.
Starts a manual CHECK.
Resets the function selected to zero (trip distance recorder or service
indicator).

8. Instrument panel lighting button.
Adjusts the brightness of the lighting of the instruments and controls.
Dials

1. Rev counter.
Indicates the speed of rotation of the engine (x 1 000 rpm).

2. Coolant temperature.
Indicates the temperature of the engine coolant (° Celsius).

3. Fuel level.
Indicates the quantity of fuel remaining in the tank.

4. Vehicle speed.
Indicates the current speed of the moving vehicle (km/h or mph).
A. Trip distance recorder.
(km or miles)

B. Distance recorder.
(km or miles)
The following two functions are displayed in succession when the
ignition is switched on.

C. Service indicator.
(km or miles) then,
Engine oil level indicator.
Displays
For further information, refer to the
paragraph which relates to the but-
ton or function and its associated
display. The following functions are displayed in
accordance with the selection.
-
Warning lights/CHECK.
- Tyre under-infl ation detection.
- Speed limiter/Cruise control.
- Automatic gearbox.
-

Navigation - Guidance/Trip computer.
- Vehicle parameters.

1
i
22
INSTRUMENTS and CONTROLS
* According to country.
The instrument panel navigator
associated with the WIP Com 3D
General menu

 Press button 1 to gain access to the
general menu and select one of the
following functions:
- "Vehicle parameters",
- "Selection of the language",
- "Selection of the units".

 Press button 2 or 3 to move on the
screen.

 Press button 1 again to confi rm the
selection. Vehicle parameters
This menu allows you to activate or
deactivate certain driving and comfort
equipment:
- selective unlocking (refer to the
"Accesses" section),
- follow-me-home and welcome lighting (refer to the "Visibility" section),
- ambient lighting (refer to the "Visibility" section),
- daytime lights (refer to the "Visibility" section),
- directional headlamps (refer to the "Visibility" section).
Selection of the language
This menu allows you to select the lan-
guage used by the display: Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Portugues, Türkçe * .
Selection of the units
This menu allows you to select the units:
temperature (°Celsius or °Fahrenheit)
and consumption (l/100 km, mpg or km/l).

This group of buttons permits:
-
when stationary , confi guration
of the vehicle’s equipment and
of the parameters of the display
(languages, units...),
- while driving , scrolling of the
active functions (trip computer,
navigation...).
Controls
There are four buttons to control the in-
strument panel 16/9 large display:

1. access the general menu, confi rm
the selection,

2. move up through the menu,

3. move down through the menu,

4. return to the previous screen, exit
from the menu. The general menu and its associat-
ed functions can only be accessed
when stationary, via buttons
1 to 4 .
A message appears on the display,
above a certain speed threshold,
indicating that the general menu
cannot be displayed.
The trip computer displays can
only be accessed while driving, via
buttons 2 and 3 (refer to the "Trip
computer" paragraph).

1
!
23
INSTRUMENTS and CONTROLS
The warning lights may come on
continuously or fl ash.
Certain warning lights may come
on in two different modes. Only by
relating the type of lighting to the
operating status of the vehicle can
it be ascertained whether the situ-
ation is normal or whether a fault
has occurred.
Indicator and warning lights
Visual indicators informing the driver
that a system is in operation (operation
or deactivation indicator lights) or of the
occurrence of a fault (warning light).
Associated warnings
The switching on of certain warning
lights may be accompanied by an audi-
ble signal and a message on the multi-
function display.
Operation indicator lights
If one of the following indicator lights
comes on, this confi rms that the
corresponding system has come into
operation.
Left-hand direction indicator.
Handbrake applied.
Right-hand direction
indicator.
Main beam headlamps.
Dipped headlamps.
Diesel engine pre-heating.
Wait until this is switched off
before operating the starter.
Front fog lamps.
Rear fog lamp.
When the ignition is switched on
The warning lights come on for a few
seconds when the vehicle’s ignition is
switched on.
When the engine is started, these warning
lights should switch off.
If they remain on, before moving off,
consult the warning light concerned.
Common operation indicator lights

1
24
INSTRUMENTS and CONTROLS
Foot on brake.
Press the brake pedal to start
the engine with the automatic
gearbox.
Specifi c operation indicator lights
The other indicator lights appear on the
large display, located in the centre of
the instrument panel.
Automatic locking.
If this is displayed, it indicates
that you have activated the au-
tomatic locking of the doors and
boot while driving.
Speed limiter.
If this is displayed, it indi-
cates that you have activat-
ed the speed limiter mode.
If this is displayed, it indi-
cates that you can set the
speed limiter speed value to
be stored. Cruise control.
If this is displayed, it indi-
cates that you have activat-
ed the cruise control mode.
If this is displayed it indi-
cates that you can set the
cruise control speed value
to be stored.
Automatic gearbox.
Automatic wiping.
If this is displayed, it indicates
that you have activated the au-
tomatic windscreen wiping.
Automatic lighting.
If this is displayed, it indicates
that you have activated the
automatic switching on of the
headlamps. This display indicates the
gear engaged in the automat-
ic or manual operation pro-
gramme.
This display indicates the op-
erating programme selected
(automatic, sport, snow or
manual).
This display indicates the posi-
tion that you have selected on
the gear selection gate (P, R, N
or D).