light PEUGEOT 308 SW BL 2012 User Guide

1INSTRUMENTS and CONTROLS












TYPE 2 INSTRUMENT PANEL

Dials


6.
Central screen.


7.
Control button.

Starts a manual CHECK and
recalls the service information.
Resets the function to zero (trip
distance recorder or service
indicator).

8.
Instrument panel lighting button.

Adjusts the brightness of the lighting
of the instruments and controls.

1.
Rev counter.

Indicates the speed of rotation of
the engine (x 1000 rpm).

2.
Coolant temperature.

Indicates the temperature of the
engine coolant (° Celsius).

3.
Fuel level.

Indicates the quantity of fuel
remaining in the tank.

4.
Vehicle speed.

Indicates the current speed of the
moving vehicle (mph or km/h).

5.
Small screen.


A.
Trip distance recorder.

(miles or km)

B.
Distance recorder.

(miles or km)

C.
Engine oil level indicator,

service indicator.

(miles or km)
These two functions are displayed
when the ignition is switched on,
then disappear after a few seconds.
Displays
For more information, refer to the
section on the button or function
and its associated display. The following functions are displayed
depending on the selection.


- Warning lamps / CHECK.



- Tyre under-infl ation detection.


- Speed limiter / Cruise control.


- Gear shift indicator.


- 6-speed electronic gear control
or automatic gearbox.


- Navigation - Guidance / Trip
computer.


- Alert messages symbol.

1INSTRUMENTS and CONTROLS












TYPE 3 INSTRUMENT PANEL WITH PEUGEOT CONNECT MEDIA
NAVIGATION (NG4 3D)


1.
Rev counter.

Indicates the speed of rotation of
the engine (x 1000 rpm).

2.
Coolant temperature.

Indicates the temperature of the
engine coolant (° Celsius).

3.
Fuel level.

Indicates the quantity of fuel
remaining in the tank.

4.
Vehicle speed.

Indicates the current speed of the
moving vehicle (km/h or mph).

5.
Small screen.


A.
Trip distance recorder.

(miles or km)

B.
Distance recorder.

(miles or km).

C.
Engine oil level indicator,

service indicator.

(miles or km)
These two functions are displayed
when the ignition is switched on,
then disappear after a few seconds.
The following functions are displayed
depending on the selection.


- Warning lamps / CHECK.


- Tyre under-infl ation detection.


- Speed limiter / Cruise control.


- Gear shift indicator.


- 6-speed electronic gear control
or automatic gearbox.


- Navigation - Guidance / Trip
computer.


- Vehicle and screen parameter
settings menus.


- Alert messages.






Dials


Displays

6.
Central screen.


7.
Control button.

Starts a manual CHECK and
recalls the service information.
Resets the function to zero (trip
distance recorder or service
indicator).

8.
Instrument panel lighting button.

Adjusts the brightness of the lighting
of the instruments and controls.
For more information, refer to the
section on the button or function
and its associated display.

1INSTRUMENTS and CONTROLS

*
According to country.









Instrument panel navigator associated
with the Peugeot Connect Media

Controls
There are four buttons to control the
large central instrument panel screen:


1.
access the main menu, confi rm the
selection,

2.
move up through the menu,

3.
move down through the menu,

4.
return to the previous screen, exit
from the menu.
Main menu


)
Press button 1
for access to the
main menu and select one of the
following functions:


- "Vehicle parameters",

- "Choice of language",

- "Choice of units".

)
Press button 2
or 3
to move on the
screen.

)
Press button 1
again to confi rm the
selection.
The main menu and its associated
functions can only be accessed
when stationary, via buttons 1
to 4
.
A message appears on the cen-
tral screen above a certain speed
threshold, indicating that the main
menu cannot be displayed.
The trip computer displays can
only be accessed while driving, via
buttons 2
and 3
(refer to the "Trip
computer" section). This group of buttons permits:


- when stationary
, confi guration of
the vehicle's equipment and of the
parameters of the central screen
(languages, units...),

- while driving
, scrolling of the
active functions (trip computer,
navigation...).


Vehicle parameters
This menu allows you to activate or
deactivate certain driving and comfort
equipment:


- wiper linked with reverse gear
(refer to the "Visibility" section),

- guide-me-home and welcome lighting
(refer to the "Visibility" section),

- interior mood lighting (refer to the
"Visibility" section),

- daytime running lamps (refer to the
"Visibility" section),

- directional headlamps (refer to the
"Visibility" section),

- rear parking sensors (refer to the
"Driving" section).


Choice of language
This menu allows you to select the lan-
guage used by the display: Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Portugues, Türkçe * .

Choice of units
This menu allows you to select the units:
temperature (°Celsius or °Fahrenheit) and
consumption (l/100 km, mpg or km/l).

1INSTRUMENTS and CONTROLS










Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the corresponding system has come into operation.
It may be accompanied by an audible signal.
Depending on your version of instrument panel, the illumination of the lamp is accompanied by:


Warning lamp



is on



Cause



Action / Observations






Left-hand
direction
indicato

r


fl ashing with
buzzer. The lighting stalk is pushed
down.




Right-hand
direction
indicator


fl ashing with
buzzer.

The lighting stalk is pushed up.





Hazard
warning
lamps


fl ashing with
audible signal. The hazard warning
lamps switch, located on
the dashboard, has been
operated. The left-hand and right-hand direction indicators
and their associated indicator lamps fl ash
simultaneously.

- a message in the multi-function
screen, or

- a pictogram in the central instrument
panel screen and a message in the
multifunction screen, or

- a pictogram and a message in the
central instrument panel screen.

1
36
INSTRUMENTS and CONTROLS


Warning lamp



is on



Cause



Action / Observations






Front
foglamps


fi xed. The front foglamps are
switched on. Turn the ring on the stalk rearwards twice to
switch off the front foglamps.




Rear
foglamps


fi xed. The rear foglamps are
switched on. Turn the ring on the stalk rearwards to switch off
the rear foglamps.




Diesel engine
pre-heating


fi xed. The ignition switch is at the
2nd position (ignition on).
Wait until the warning lamp has switched off before starting.
The duration for which the warning lamp is on is
determined by the climatic conditions.




Parking brake


fi xed. The parking brake is applied
or not properly released. Release the parking brake to switch off the
warning lamp, keeping your foot on the brake
pedal.
Observe the safety recommendations.
For further information on the parking brake, refer
to the "Driving" section.



Dipped beam
headlamps


fi xed. The lighting stalk is in the
"Dipped beam headlamps"
position or in the "AUTO"
position in conditions of low
light.




Main beam
headlamps


fi xed. The lighting stalk is pulled
towards you. Pull the stalk again to return to dipped beam
headlamps.

1
37
INSTRUMENTS and CONTROLS


Stop & Start


fi xed. When the vehicle stops (red
lights, traffi c jams, ...) the
Stop & Start system has
put the engine into STOP
mode. The warning lamp goes off and the engine
restarts automatically in START mode, as soon
as you want to move off.

fl ashes for a
few seconds,
then goes off. STOP mode is temporarily
unavailable.
or
START mode is invoked
automatically. Refer to "Driving - § Stop & Start" for special
cases with STOP mode and START mode.

Warning lamp



is on



Cause



Action / Observations





Passenger's
front airbag
fi xed on the
seat belt and
passenger's
front airbag
warning lamps
display. The control switch, located
on the passenger's side of
the dashboard, has been
placed in the "ON"
position.
The passenger's front
airbag is activated.
In this case, do not install a
"rear facing" child seat. While you do not have a rear-facing child
seat fi tted to the front passenger seat, it is
recommended that the passenger's front airbag
be activated.
On the other hand, before fi tting a rear-facing
child seat, you must turn the control switch to the
"OFF"
position.

1
44
INSTRUMENTS and CONTROLS









Lighting dimmer

Permits manual adjustment of the bright-
ness of the instruments and controls to
suit the ambient light level. Only operates
when the vehicle lighting is on, with the
exception of the daytime running lamps.

Activation


)
Press the button to change the
brightness of the instruments and
controls.

)
When the lighting reaches the
minimum setting, release the
button, then press again to
increase it.
or


)
When the lighting reaches the
maximum setting, release the
button, then press again to reduce
it.

)
When the lighting reaches the level
of brightness required, release the
button.

Deactivation
When the vehicle lighting is off, or in
day mode on vehicles fi tted with day-
time running lamps, pressing the button
does not have any effect.

2
50
MULTIFUNCTION SCREENS

"Diagnosis vehicle"
menu


)
Press the "MENU"
button for access
to the main menu.

)
Press the arrows, then the "OK"

button to select the " Diagnosis
vehicle
" menu.


)
On the " Diagnosis vehicle
" menu,
select the following application:



Alert log
This summarises the active warning
messages, displaying them in succes-
sion on the multifunction screen. Once this menu has been selected, you
can consult information concerning the
status of the vehicle, such as the alert log.

Defi ne the vehicle parameters
Once this menu has been selected, you
can activate or deactivate the following
equipment:


- wiper linked with reverse gear (see
"Visibility"),

-
"guide-me-home" lighting (see "Visibility"),


- interior mood lighting (see "Visibility"),

- daytime running lamps (see "Visibility"),

- rear parking sensors (see "Driving").


"Personalisation-
Configuration" menu
Once this menu has been selected, you
can gain access to the following func-
tions:


- defi ne the vehicle parameters,

- display confi guration,

- choice of language.

2
51
MULTIFUNCTION SCREENS

For safety reasons, confi guration
of the multifunction screen by the
driver must only be done when sta-
tionary.



"Telephone" menu


Display confi guration
Once this menu has been selected, you
can gain access to the following set-
tings:


- brightness-video setting,

- date and time setting,

- choice of units.


Choice of language
Once this menu has been selected,
you can change the language used by
the display (Deutsch, English, Espanol,
Français, Italiano, Nederlands, Portugues,
Portugues-Brasil, Russe, Türkçe * ).
Example: setting of the duration of the
"guide-me-home" lighting


)
Press the " 
" or " 
" buttons, then
the "OK"
button to select the menu
required.


)
Press the " 
" or " 
" buttons,
then the "OK"
button to select the
"Guide-me-home headlamps" line.


)
Press the " 
" or " 
" buttons to
set the value required (15, 30 or
60 seconds), then press the "OK"

button to confi rm.

)
Press the " 
" or " 
" buttons, then
the "OK"
button to select the "OK"

box and confi rm or press the "ESC"

button to cancel.
With the Peugeot Connect Sound
(RD5) switched on, once this menu has
been selected you can confi gure your
Bluetooth system (pairing), consult the
various telephone directories (calls log,
services...) and manage your communi-
cations (pick up, hang up, call waiting,
secret mode...).
For more information on the "Tele-
phone" application, refer to the Peugeot
Connect Sound (RD5) section.

*
According to country.

2
53
MULTIFUNCTION SCREENS



)
Press the "SETUP"
button to gain
access to the confi guration menu:


- "Display confi guration",

- "Voice synthesis",

- "Choice of language",

- "Vehicle parameters",

- "Alert log".


Display confi guration
This menu allows you to choose a col-
our scheme for the screen, to adjust the
brightness, set the date and time and
choose the units for distance (km or
miles), fuel consumption (l/100 km, mpg
or km/l) and temperature (°Centigrade
or °Fahrenheit).

When setting the time, you can
select " Synchronise minutes
with GPS
", so that the minutes
are set automatically by satellite
reception.

For safety reasons, confi guration
of the multifunction screen by the
driver must only be done when sta-
tionary.
Alert log
It lists the active alerts by displaying
their associated messages in turn.

Choice of language
This menu allows you to choose the
language used by the screen (French,
English, Italian, Portuguese, Spanish,
German, Dutch, Turkish, Polish, Russian).
Voice synthesis
This men allows you to adjust the vol-
ume for navigation instructions and to
choose the type of voice (male or fe-
male).
Vehicle parameters *
This menu allows you to activate or
deactivate certain driving and comfort
equipment, arranged by category:

- Parking assistance


- Operation of wipers



●
Enagages rear wiper linked to
reverse (Rear wiper operates in
reverse gear; refer to "Visibility"),

-
Lighting confi guration (see "Visibility"):



●
Duration of the guide-me-home
lighting,

●
Directional headlamps (main/
additional directional lighting),

●
Mood lighting (Interior mood
lighting),

●
Daytime running lamps function ** .



"SETUP" menu


*
Depending on version.

**
According to country of sale.