tow PEUGEOT 4007 2007 Owners Manual

Page 17 of 221

1
CRUISE
INSTRUMENTS and CONTROLS
INSTRUMENT PANEL INDICATOR LIGHTS

Indicator lights is on Cause Observations
Left-hand
direction
indicator Flashing
with
buzzer This fl ashes when you
press the lights stalk
down. If this indicator light fl ashes abnormally quickly,
this could indicate that the electric bulb of one
of the direction indicators has blown. Change
the bulb or contact a PEUGEOT dealer.
Right-hand
direction
indicator Flashing
with
buzzer This fl ashes when you
push the lights stalk up. If this indicator light fl ashes abnormally quickly,
this could indicate that the electric bulb of one
of the direction indicators has blown. Change
the bulb or contact a PEUGEOT dealer.
Main beam
headlamps Fixed This comes on when
you pull the lights stalk
towards you. Pull the stalk to return to dipped headlamps.
Side lights Fixed This comes on when
the lights stalk is in the
"Side lights" or "Dipped
headlamps" position. Turn the stalk to the position required.
Front fog
lamps Fixed This comes on when you
use the front fog lamps. Turn the ring on the stalk forwards to switch on
the fog lamps.
Rear fog
lamps Fixed This comes on when you
use the rear fog lamps. Turn the ring on the stalk forwards to switch on
the fog lamps.
Cruise control Fixed This comes on when the
mode is active. Press the "ON/OFF" button to activate/
deactivate the mode.

Page 44 of 221

2
i
COMFORT
For even air distribution, take care not
to obstruct the exterior air intake grille
located at the bottom of the windscreen,
the vents, the air outlets under the front
seats and the air extractor located be-
hind the fl aps in the boot.
In certain cases of particularly arduous
use (towing the maximum load on a
steep gradient in hot weather), cutting
off the air conditioning permits recovery
of the engine power and therefore im-
provement of the towing capacity.
Close the windows to benefi t from the
full effectiveness of the air conditioning.
Ensure that the passenger compart-
ment fi lter is in good condition. Have
the fi lter elements replaced periodically.
If you drive in a dusty environment, re-
place it twice as often.
The air conditioning system does not
contain chlorine and is not harmful to
the ozone layer.
Operate the air conditioning system for
5 to 10 minutes, once or twice a month,
to keep it in perfect working order. The water formed by the air condition-
ing condensation is discharged via
an opening provided for this purpose.
Therefore, a puddle of water may form
underneath the vehicle when stationary.
If the system does not produce cold air,
do not use it and contact your PEUGEOT
dealer.

1. Centre panel vents.

2. Temperature sensor.

3. Air outlet to passenger footwells.

4. Side vents.

5. Front windows de-icing or demisting
vents.

6. Windscreen de-icing or demisting
vents.

7. Sunshine sensor. AUTOMATIC REGULATION OF TIC REGULATION OF
THE AIR CONDITIONING
Use of the automatic regulation of the
air conditioning is recommended. It per-
mits automatic and optimised control of
all of the following functions: air fl ow,
passenger compartment temperature
and air distribution, by means of vari-
ous sensors (exterior temperature,
interior temperature, sunshine), so
preventing the need for you to change
your reference settings other than the
value displayed.
Do not cover the temperature and hu-
midity sensor 2 and the sunshine sen-
sor 7 .
They are required for regulation of the
air conditioning.
Advice on operation
In hot weather, in order to obtain
intense ventilation, it is advis-
able to use vents 1 and 4 only.
If, when the vehicle has been
parked in the sun for a long
time, the interior temperature re-
mains very high, do not hesitate
to ventilate the passenger com-
partment for a few minutes. Switch off the air conditioning
when the climatic conditions
permit.

Page 47 of 221

2
i
COMFORT
Manual operation
It is possible to set one or more func-
tions manually while leaving the other
functions in automatic mode.

Switching to manual mode may result
in discomfort (temperature, humidity,
odour, condensation) and does not of-
fer optimum comfort. Temperature adjustment (3) Air fl ow adjustment (2)

 Turn the dial to the
right to increase the
air fl ow or to the left to
decrease it.

 Turn the temperature
control dial to the right
to increase the tem-
perature and to the
left to decrease it.
The temperature can be set from 15
to 29.

 Place the dial in the
position required to di-
rect the air towards:
To avoid condensation and dete-
rioration of the quality of the air
in the passenger compartment,
ensure that a suffi cient fl ow of
air is maintained.
the central and side vents,
the central and side vents and
the footwells,
the footwells,
the windscreen, the side win-
dows and the footwells, the windscreen and the side
windows.
The air distribution can be adapted by
placing the adjustment dial in the inter-
mediate positions.
Air distribution adjustment (1)

Page 73 of 221

2
COMFORT
12 volt socket (120 W max)
This operates when the ignition switch
is in the "ON" or "ACC" position.
Lift the cover to gain access to the
socket. Check that the electrical equip-
ment operates with 12 volts and
that its maximum electrical pow-
er is 120 W.
The prolonged use of electrical
equipment without running the
engine may discharge the bat-
tery.
Stowing rings
There are four stowing rings in the boot
for securing luggage:
- two rings are located on the boot
fl oor,
- two rings are located on the rear side pillars.
* On 5-seat version only.
Raise the boot fl oor to gain access to
this compartment.
Right-hand side enclosed storage
compartment
This storage compartment contains the
tools for changing a wheel. Storage compartment in the fl oor *

Page 74 of 221

2
i
COMFORT
Load space cover
Unroll the load space cover and install it
in the securing groove A .
To store the load space cover, release
it from the securing groove, it rolls up to
its initial position. Second installation position.
The load space cover can be secured
in two different positions
B , so that the
row 2 seat backs can be tilted.

1. Roll up the load space cover.

2. Move one of the slides C towards
the inside of the vehicle and insert
the tab D in the installation hole to
be used.
Move the opposite slide in the same way.

3. After changing the position, check
that the load space cover is secured
correctly. Removing the load space cover.

1. Roll up the load space cover.

2. Move one of the slides C towards the
inside of the vehicle and raise it.
Release the opposite slide in the same way.
To put the load space cover in place, car-
ry out the operations in reverse order.
Take care not to place heavy
objects on the load space cover
when it is unfolded. The load space cover can be
stored along the lower tail-
gate, unless audio equipment is
present.

Page 77 of 221

3
i
ACCESS
Starting the vehicle

 Insert the key in the ignition switch.

 Operate the starter by turning the
key to position 4 (START) .

 When the engine turns over, release
the key. The ignition switch is placed
in position 3 (ON) automatically. Switching the vehicle off

 Park the vehicle.

 While pressing the key, turn it
towards you to position 1 (LOCK) .

 Remove the key from the ignition
switch. Changing the battery
Battery reference: CR1616/3 volts.

 Unclip the casing using a coin at the
notch.


Slide the fl at battery out of its housing.

 Slide the new battery into its housing
observing the original direction.

 Clip the casing.
Key in ignition
A buzzer sounds on opening the
driver’s door, if the key has been
left in the ignition.

Page 81 of 221

3
i
ACCESS
Starting the vehicle

 Insert the key in the ignition switch.

 Operate the starter by turning the
key to position 4 (START) .

 When the engine turns over, release
the key. The ignition switch is placed
in position 3 (ON) automatically. Switching the vehicle off

 Park the vehicle.

 While pressing the key, turn it
towards you to position 1 (LOCK) .

 Remove the key from the ignition
switch. Changing the battery
Battery reference: CR1616/3 volts.

 Unclip the casing using a coin at the
notch.


Slide the fl at battery out of its housing.

 Slide the new battery into its housing
observing the original direction.

 Clip the casing.
Key in ignition
A buzzer sounds on opening the
driver’s door, if the key has been
left in the ignition.

Page 98 of 221

4
VISIBILITY
WIPER CONTROLS WIPER CONTROLS
System for selection and control of the
various front and rear wiping modes for
the elimination of rain and cleaning.
The vehicle’s various front and rear wip-
ers are designed to improve the driver’s
visibility progressively in relation to the
climatic conditions. Manual controls
The wiper commands are issued direct-
ly by the driver by means of the lever A
and the ring B . single wipe.
Windscreen wipers

A. wiping speed selection lever:
park.
intermittent (the speed can be
set manually),
slow.
fast.

B. intermittence adjustment ring.
You can increase or decrease the wip-
ing frequency when the intermittent
mode is active. Windscreen wash
Pull the wipers stalk towards you. The
windscreen wash then the wipers oper-
ate for a set time.
The headlamp wash is also activated
if
the dipped headlamps are on .
Headlamp wash
Press the end of the lights stalk to ac-
tivate the headlamp wash, when the
dipped headlamps are on.

Page 109 of 221

6
99
DIRECTION INDICATORS
Selection of the left or right direction in-
dicators to signal a change of direction
of the vehicle.
HAZARD WARNING LIGHTS HAZARD WARNING LIGHTS
A visual warning by means of the direc-
tion indicators to alert other road users
to a vehicle breakdown, towing or ac-
cident.
HORN
Audible warning to alert other road us-
ers to an imminent danger.

 Lower the lights stalk when moving
to the left (position 1 ).

 Raise the lights stalk when moving
to the right (position 1 ).
The indicator light on the instrument
panel fl ashes.
As a safety precaution in a traffi c
jam, switch on the hazard warn-
ing lights when you are the last
in the queue.

 Press button A , the direction indica-
tors fl ash.
They can operate with the ignition off.
 Press one of the spokes of the
steering wheel.
The "motorway" function
System for indicating a change of lane
on a motorway.
Press up or down once (positions 2 ),
without passing the point of resistance;
the corresponding direction indicators
will fl ash three times.

Page 119 of 221

7
DRIVING
HANDBRAKE HANDBRAKE
Mechanical brake to hold the vehicle
when stationary.
Releasing

 Pull on the handle and press the
button A to release the handbrake.
Applying

 Pull the handbrake to immobilise
your vehicle.
When parking on a slope, direct your
wheels towards the pavement and ap-
ply the handbrake.
6 - SPEED MANUAL GEARBOX 6 - SPEED MANUAL GEARBOX
Reverse
To change to reverse gear, lift the ring
under the gear lever knob and push the
gear lever to the left then to the front.

Reverse gear can only be engaged
when the vehicle is stationary with
the engine idling.
When the vehicle is being
driven, the displaying of this
screen indicates that the
handbrake is still on or has
not been properly released.

Page:   1-10 11-20 21-30 next >