ESP PEUGEOT 4007 2008 Owners Manual

1
INSTRUMENTS and CONTROLS
Prevention messages
Information messages (ignition at "ON")

Message is on Status of the system
2WD two wheel
drive system
Flashing When the "2WD" (2 wheel drive) mode is selected using the tran
smission
mode selector.
4WD four wheel
drive system
Flashing When the "4WD" (4 wheel drive) mode is selected using the tran
smission
mode selector.
This mode is the default mode.
4WD LOCK four
wheel drive system
Flashing When the "LOCK" (4 wheel drive) mode is selected using the
transmission mode selector.
Dynamic stability
control system
(ASC)
Fixed When the dynamic stability control system (ASC) is active.
Exterior
temperature
Fixed This indicates the exterior temperature.
When the vehicle is stationary or if the speed is b
elow 12 mph (20 km/h) the
temperature displayed may not correspond to the ext erior temperature.

Display is on Cause Solution - action Observations
Service
indicator
Fixed Informs the driver of the
time remaining before
the vehicle’s scheduled
service.
Consult a PEUGEOT
dealer. This is displayed for a few seconds
when the ignition is switched on.

Break
advised
Fixed Informs the driver that
he should stop to take
a break. You are advised to
take a break. This is displayed when the driving
time that you set previously is
reached.
An audible signal is heard 3 times
and is then heard every 5 minutes
until the vehicle stops.

1
i
i
ii
INSTRUMENTS and CONTROLS
Choice of the display language
(LANGUAGE)
You can choose between different
languages for the display.
On the menus screen:

 press the INFO button to select

"LANGUAGE" .

 press and hold the INFO button
for a few seconds to display the

"LANGUAGE" screen.


press the INFO button to scroll the lan-
guages (Japonais, English, Deutsch,
Français, Espanol, Italiano, "---" and
PREVIOUS) in succession.

 press and hold the INFO button for
a few seconds to confi rm your se-
lection.
If you select the parameter "---",
no message will be displayed in
message display situations. If the battery is disconnected, the
parameter memory is cleared and
the default language (ENGLISH)
is restored automatically.
Activation/deactivation of the
"INFO" button sound
You can activate or deactivate the INFO
button sound.
On the menus screen:

 press the INFO button to se-
lect the INFO button sound
activation/deactivation sym-
bol (located on menu 2/2) .

 press and hold the INFO button for
a few seconds to scroll the choices
(ON, OFF) in succession.
The mode selected is confi rmed.
If the battery is disconnected, the
parameter memory is cleared
and the default choice (ON) is
restored automatically. Changing the display interval of
the "BREAK ADVISED" message
You can change the display interval of
the
"BREAK ADVISED" message.
On the menus screen:

 press the INFO button to select

"ALERT" (located on menu 2/2) .

 press and hold the INFO button
for a few seconds to display the

"ALERT" screen.

 press the INFO button to select
the display interval of the "BREAK
ADVISED" message.

 press and hold the INFO button for
a few seconds to confi rm.
If the battery is disconnected, the
parameter memory is cleared
and the default value (OFF) is
restored automatically.

3
i
i
ACCESS
The electric window switches
can be confi gured via the colour
display "Equipment" menu.
The electric window switches
remain operational for approxi-
mately 30 seconds after the
ignition is switched off and the
switch on the driver’s door re-
mains operational for a further
30 seconds when the door is
opened.
The windows can no longer be
opened or closed after the driv-
er’s door is closed.
The rear windows do not lower
fully.

1. Driver’s electric window switch.

2.
Passenger’s electric window switch.

3. Rear right electric window switch.

4. Rear left electric window switch.

5. Disarming of the passenger and
rear electric window switches. In the event of unwanted open-
ing of the window on closing
(for example in the presence of
frost), reinitialise the electric win-
dows (refer to the corresponding
paragraph).
Safety auto-reverse
In automatic mode, when the window
rises and meets an obstacle, it stops
and lowers again.
Operation
With the ignition on, you have two op-
tions:
-
manual mode

 Press the switch gently to open or
pull it gently to close. The window
stops as soon as the switch is re-
leased.
- automatic mode

 Press the switch fully to open or
pull it fully to close. The window
opens or closes completely when
the switch is released.

 Pressing the switch again stops
the movement of the window.
System which opens or closes a window
manually or automatically. It is fi tted with
a system which provides protection if an
obstacle is detected on one-touch mod-
els and a deactivation system to prevent
misuse of the rear controls.

3
i
ACCESS
Disarming the passenger and rear
electric window switches Reinitialising the electric windows
Following reconnection of the battery or
after the safety auto-reverse has been
triggered three times in succession, you
must reinitialise the safety auto-reverse
function:

 with the door closed, lower the win-
dow completely then raise it again, it
will rise in steps of a few centimetres
each time the switch is pressed, re-
peat the operation until the window
is fully closed,

 continue to press the switch for at
least one second after reaching the
window closed position. Always remove the key from the
ignition when leaving the vehi-
cle, even for a short time.
In the event of contact during
operation of the windows, you
must reverse the movement of
the window. To do this, press the
switch concerned.
When the driver operates the pas-
senger electric window switches,
he must ensure that no one is
preventing correct closing of the
windows.
The driver must ensure that the
passengers use the electric win-
dows correctly.
Be aware of children when oper-
ating the windows.

 For the safety of your children, press
switch 5 to prevent operation of the
passenger and rear electric windows
irrespective of their position.
When the button is pressed down, dis-
arming is active.
When the button is raised, disarming is
deactivated.
When the button is pressed
down, you can open or close all
of the windows using the switch-
es on the driver’s door.
The safety auto-reverse function is
not active during these operations.

4
i
VISIBILITY
LIGHTS STALK LIGHTS STALK
Main lighting
The various front and rear lights of the
vehicle are designed to adapt the driv-
er’s visibility progressively in relation to
the climatic conditions:
- side lights, to be seen,
- dipped headlamps to see without dazzling other drivers,
- main beam headlamps to see clear- ly when the road isclear.
Additional lighting
Other lights are installed to fulfi l the re-
quirements of particular driving condi-
tions:
- rear fog lamps to be seen from a distance,
- front fog lamps for even better vis- ibility,
- daytime lights to be seen during the day. Manual controls
The lighting commands are issued di-
rectly by the driver by means of the ring

A and the lever B . lights off,
automatic switching on of the
lights,
side lights only,

B. lever for inversion of the lights by
pulling: dipped headlamps/main
beam headlamps.
In the lights off and side lights modes,
the driver can switch on the main beam
headlamps directly ("headlamp fl ash")
for as long as he pulls the lever.
Displays
Lighting of the corresponding indicator
light on the instrument panel confi rms
the selective switching on of the lighting
selected.

A. main lighting mode selection ring,
with:
dipped headlamps or main
beam headlamps.
System for selection and control of the
various front and rear lights providing
the vehicle’s lighting.
Certain functions of the lights
stalk (automatic lighting, sensitiv-
ity) can be confi gured via the co-
lour display "Equipment" menu.

4
i
VISIBILITY
COURTESY LIGHTS COURTESY LIGHTS Front courtesy light Map reading lights
There are two map reading lights, one
on each side of the courtesy light.
Press the corresponding transparent
block A .
Position 1
The courtesy light comes on when a
door or the tailgate is opened.
When the door or the tailgate is closed
again, the lighting gradually dims for a
few seconds before switching off.
However, the courtesy light is switched
off automatically in the following cases:
- When the doors and the tailgate
are closed and the ignition switch is
placed in the "ON" position.
- When the doors and the tailgate are closed and you lock the vehicle from
inside or using the remote control.
System for selection and control of the
various passenger compartment lights.
Position 2
The courtesy light is off, regardless of wheth-
er the doors or tailgate are open or closed.
The durations of lighting of the
front courtesy lights can be con-
fi gured via the colour display
"Equipment" menu.

6
i
SAFETY
99
DIRECTION INDICATORS
HAZARD WARNING LIGHTS
HORN

 Lower the lights stalk when moving
to the left (position 1 ).

 Raise the lights stalk when moving
to the right (position 1 ).
The indicator light on the instrument
panel fl ashes.
As a safety precaution in a traffi c
jam, switch on the hazard warn-
ing lights when you are the last
in the queue.

 Press button A , the direction indica-
tors fl ash.
They can operate with the ignition off.
 Press one of the spokes of the
steering wheel.

Selection of the left or right direction
indicators to signal a change of direction
of the vehicle
.
The "motorway" function
System for indicating a change of lane
on a motorway.
Press up or down once (positions
2 ),
without passing the point of resistance;
the corresponding direction indicators
will fl ash three times.
A visual warning by means of the direc-
tion indicators to alert other road users to
a vehicle breakdown, towing or accident. Audible warning to alert other road
users to an imminent danger.
Certain direction indicator func-
tions can be confi gured via the
colour display "Equipment" menu.

6
SAFETY
107
Side air bags
System which protects the driver and
passenger in the event of a serious side
impact in order to limit the risk of injury
to the chest.
Each side air bag is incorporated in
the front seat back frame, on the door
side.
Activation
The side air bag is triggered unilater-
ally in the event of a serious side impact
applied to all or part of the side impact
zone B , perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane and directed from the outside to-
wards the inside of the vehicle.
The side air bag infl ates between the
front occupant of the vehicle and the
corresponding door trim pad. Curtain air bags
System which protects the driver and
passengers (with the exception of the rear
centre passenger and the passengers of
row 3) in the event of a serious side impact
in order to limit the risk of injury to the head
.
Each curtain air bag is incorporated in
the pillars and the upper section of the
passenger compartment. Activation
The curtain air bag is triggered at the
same time as the corresponding side air
bag in the event of a serious side impact
applied to all or part of the side impact
zone
B , perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane and directed from the outside to-
wards the inside of the vehicle.
The curtain air bag infl ates between the
front or rear occupant of the vehicle and
the windows.
In the event of a minor impact or
bump on the side of the vehicle
or if the vehicle rolls over, the air
bag may not be triggered.
In the event of a rear or front
collision, the air bag is not trig-
gered.
Impact detection zones

A. Front impact zone.

B. Side impact zone.
Operating fault
If this warning light comes on on the in-
strument panel and this display appears
on the instrument panel display, contact
a PEUGEOT dealer to have the system
checked. The air bags may no longer be
triggered in the event of a serious impact.

7
2WD4WD LOCK4WD AUTO
DRIVING
FOUR WHEEL DRIVE SYSTEM
WITH ELECTRONIC CONTROL
4WD AUTO (position 1)
The vehicle operates with four wheel drive
and provides optimum traction regardless
of the level of grip.
This is the vehicle’s normal and regular
operating mode, the distribution of the
torque between the front and rear axles
is controlled automatically.
The distribution favours the front wheels,
the transfer of torque to the rear wheels
is managed electronically by the control
unit in relation to the level of grip, so
guaranteeing optimum road holding.

Three transmission modes are available
and can be selected manually by the driver
in accordance with his requirements.
You can change transmission mode
when stationary or while driving at a
speed below 60 mph (100 km/h) .
The transmission mode can be selected
by turning the control A . Display on the instrument panel
The transmission mode is displayed in
the form of an intermittent display on
the instrument panel display when the
transmission mode is selected.
Selecting the transmission
mode
The selection of this mode is
recommended when the level of
grip permits.
2WD (position 3)
The vehicle operates with front two
wheel drive.
This mode corresponds to use on a tarma-
cked road on which the driver considers that
there is no risk of loss of grip (dry road).
4WD LOCK (position 2)
The vehicle operates with four wheel
drive in this mode also.
It is recommended when grip is particularly
poor or diffi cult (sand, mud, slopes, ...).
System which permits the selection of
a transmission mode in relation to the
driving conditions.

7
i
DRIVING
Programming

 Press button 1 .

 Set the programmed speed by ac-
celerating to the required speed, then
press button 2 "COAST SET" .
CRUISE CONTROL
The controls of this system are grouped
together on the steering wheel.

1. "ON/OFF" button: activation/deacti-
vation of the cruise control mode.

2. "COAST SET" button: storing of a
driving speed and decreasing of the
cruising speed.

3. "ACC RES" button: increasing of
the cruising speed and recalling of
the stored speed.

4. "CANCEL" button: switching off of
the cruise control. When you press button
1 , the "CRUISE"
indicator light comes on on the instru-
ment panel.
Steering wheel controls Display on the instrument pan
el
The cruise control cannot, in any
circumstances, take the place of the
need to comply with speed limits or
of the vigilance and responsibility of
the driver.

System which permits automatic main-
taining of the vehicle speed at the value
programmed by the driver, without any
action on the accelerator pedal.
The cruise control is
switched on manually:
the vehicle speed must be 25 mph (40 km/h)
minimum and second gear must be engaged
in the case of a manual gearbox.
The cruise control is switched off manual-
ly, by an action on the brake or clutch pedal
or if the ASC system is triggered.

The programmed speed can be exceed-
ed temporarily by pressing the accelera-
tor pedal.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value.