clock PEUGEOT 4007 2008 Owners Manual

1
i
INSTRUMENTS and CONTROLS
MONOCHROME DISPLAMONOCHROME DISPLAY
This provides the following information:
- the time,
- the audio equipment displays (refer to the "Audio and Telematics" section). Setting the time
The digital clock can be set in
automatic
mode or in manual mode . Selecting the Setting
Select the
automatic mode or the

manual mode as follows:

 Press button A "PWR" to switch on
the audio system.

 Access the setting mode by press-
ing button B "TUNE" for approxi-
mately 2 seconds.

 Press button B "TUNE" several
times to scroll through the various
menus and select the CT menu
(clock time).
The order of the menus is the
following: AF/CT/REG/TP-S/PTY
display language/SCV/PHONE/
Functions setting mode OFF.
Automatic mode
This mode permits automatic setting of
the local time using the signal from the
RDS stations.
The symbol
"CT" appears on the display.
Manual mode
This mode permits manual setting of
the time using the audio equipment
buttons.
It can also be used when the "Automatic
mode" displays an inaccurate time, when
the local RDS stations are broadcasting
from a different time zone.

1
i
i
INSTRUMENTS and CONTROLS
Set the time using the buttons as indi-
cated below:

 with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK button until the
time display fl ashes.

 Press the appropriate button to set
the time:

Button
H: setting of the hours
The hours digits scroll when you press
this button.

Button M: setting of the minutes
The minutes digits scroll when you
press this button.

Button: 00: resetting of the minutes to
zero.
- from 1 to 29 min
: rounded down to
the previous hour,
- from 30 to 59 min: rounded up to
the next hour.
Manual mode
Automatic mode
In this mode, setting is automatic using
the signal from the RDS radio stations.
 After setting the time, press the

DISP button; the time display stops
fl ashing.
The digital clock does not display
seconds.
When the "minutes" display is
set or reset to zero, the clock
starts at the zero second of the
minute selected.
The time setting is lost if the
battery is disconnected.

 Turn button B "TUNE" to the left or
to the right to select "CT ON" (auto-
matic mode) or "CT OFF" (manual
mode).

 After selecting the mode, you can exit
the "Functions setting mode"menu
by pressing button B "TUNE" for ap-
proximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "functions setting mode"
menu automatically.

1
INSTRUMENTS and CONTROLS
Setting the time
The digital clock is set automatically .
This mode enables the system to set
the local time automatically using the
signal from the RDS stations.

 On the control panel, press button

B
(SET) to access the "Settings"
menu.

 On the touch screen, press button

B to access the "System" menu.
The system settings screen is displayed.
"Information" menu
On the control panel, press button
D
(INFO) to access the "Info" screen and
consult:
- "Support info" to display the soft-
ware and data versions,
- "Vehicle position" to display the
GPS location of the vehicle,
- "Calendar" to make a note of
events, birthdays, etc.,
- "Journey" to display the average
speed, the consumption, the dis-
tances and the duration of driving,
- "Environment" to display the altitude,
the atmospheric pressure, the exterior
temperature (the ice symbol is dis-
played if there is a risk of ice),
- "Air conditioning" to display the
information relating to the air condi-
tioning,
-

"Mobile telephone" to enter a number,
delete a character, make or receive a
call.
"Map" menu
On the control panel, press button
E
(NAVI) to access the "Routes Menu"
screen and select:
- "Detour" to make a detour through
a specifi ed region,
- "Route" to change the route,
- "Display a route" to display a route
in different ways,
- "Delete a route" to delete a route,
- "Local POI" to search for the POIs
in the surrounding area.

1
INSTRUMENTS and CONTROLS
Setting the time
The digital clock is set automatically .
This mode enables the system to set
the local time automatically using the
signal from the RDS stations.

 On the control panel, press button

B
(SET) to access the "Settings"
menu.

 On the touch screen, press button

B to access the "System" menu.
The system settings screen is displayed.
"Information" menu
On the control panel, press button
D
(INFO) to access the "Info" screen and
consult:
- "Support info" to display the soft-
ware and data versions,
- "Vehicle position" to display the
GPS location of the vehicle,
- "Calendar" to make a note of
events, birthdays, etc.,
- "Journey" to display the average
speed, the consumption, the dis-
tances and the duration of driving,
- "Environment" to display the altitude,
the atmospheric pressure, the exterior
temperature (the ice symbol is dis-
played if there is a risk of ice),
- "Air conditioning" to display the
information relating to the air condi-
tioning,
-

"Mobile telephone" to enter a number,
delete a character, make or receive a
call.
"Map" menu
On the control panel, press button
E
(NAVI) to access the "Routes Menu"
screen and select:
- "Detour" to make a detour through
a specifi ed region,
- "Route" to change the route,
- "Display a route" to display a route
in different ways,
- "Delete a route" to delete a route,
- "Local POI" to search for the POIs
in the surrounding area.