start stop button PEUGEOT 4007 2011.5 Owners Manual

1
INSTRUMENTS and CONTROLS
Set the time using the buttons as
indicated below:


)
with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK
button until the
time display fl ashes.

)
Press the appropriate button to set
the time:

Button
H:
to set the hours
The hours digits scroll when you press
this button.

Button M:
to set the minutes
The minutes digits scroll when you
press this button.

Button 00:
to reset the minutes to
zero.


- from 1 to 29 min
:
rounded down to
the previous hour,

- from 30 to 59 min:
rounded up to
the next hour.


)
After setting the time, press the
DISP
button; the time display stops
fl ashing.


Manual mode

Automatic mode

In this mode, setting is automatic using
the signal from the RDS radio stations. The digital clock does not display
seconds.
When the "minutes" display is
set or reset to zero, the clock
starts at the zero second of the
minute selected.
The time setting is lost if the
battery is disconnected.


)
Turn button B
"TUNE" to the left or
to the right to select "CT ON"
(auto-
matic mode) or "CT OFF"
(manual
mode).

)
After selecting the mode, you can
exit the "Functions setting mode"
menu by pressing button B
"TUNE"
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the "Functions setting mode"
menu automatically.

3
ACCESS















Keys

Make a careful note of the number of each key. This number is coded on the label attached to the key.
If the keys are lost, a PEUGEOT dealer can supply you with new keys.








Do not throw the remote control batteries away, they contain metals which are harmful to the environment.
Take them to an approved collection point.


Remote control

The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a
possibility that it may unlock the vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and out of sight of your vehicle. You run the
risk of stopping it from working.
The remote control does not operate when the key is in the ignition, even when the ignition is switched off.


Locking the vehicle

Driving with the doors locked may make access to the passenger compartment by the emergency services more
diffi cult in an emergency.

As a safety precaution (with children on board), remove the key from the ignition when you leave the vehicle, even for a short time.


Anti-theft protection

Do not make any modifi cations to the electronic engine immobiliser system, this could cause malfunctions.


When purchasing a second-hand vehicle

Have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones
which can start the vehicle.

11
AUDIO EQUIPMENT and TELEMATICS

Matching your Bluetooth®
telephone
The system can register up to 7 Bluetooth®
compatible mobile telephones.
The telephone which has the highest
level of priority is connected automati-
cally.
It is absolutely essential that the vehicle
is parked in a safe place with the parking
brake applied.
1 - Press the SPEAK button.
7 - Say a 4-digit number which will
be recorded as the matching
code. 12 - After the audible signal, allo-
cate a name to the telephone
by saying the name of your
choice.
13 - The system says "Allocate an order
of priority between 1 and 7. One is
the highest level of priority".
If the system does not detect the
Bluetooth
® compatible mobile
telephone, the matching proc-
ess stops accompanied by an
audible signal.
If you select a level of priority
which has already been allo-
cated to another telephone, the
system asks you if you wish to
replace this level of priority. Remember this matching code as
you must enter it in the telephone
in one of the following steps of
the matching procedure.
9 - The system says "Start the match-
ing procedure on the telephone.
Consult the instructions in the tel-
ephone manual".
2 - Say "Confi gure".
3 - Say "Matching options".
5 - Say "Match a telephone". 8 -
The system confi rms the validity of
the number spoken, answer "Yes".
Say "No" to return to step 7.

10 - Consult your mobile tele-
phone's user manual and
enter the matching code
recorded in step 7 in the
telephone. 14 - Say a number between 1 and
7 to establish the level of pri-
ority of the mobile telephone.
15 - The system says and confi rms the
<name of the telephone> and the
<number> of its priority.
16 - Answer <Yes> or say <No>
to return to step 13.
17 -
The systems says "Matching com-
plete" then emits an audible signal and
deactivates the voice recognition
.
4 - The system says "Do you wish to
match a telephone, delete a tele-
phone or obtain the list of matched
telephones?".
6 - The systems says "Please say the
4 digits of a matching code". If the code is incorrect, the system
locks. To clear the code:


- check that the telephone's
voice recognition is not acti-
vated,

- with the ignition on and the
audio system active, press
the HANG UP button for
2 seconds, 3 times in suc-
cession.
11 - When it detects a Bluetooth
® com-
patible mobile telephone, the system
says "Please say the name of the
telephone after the bleep".