tailgate PEUGEOT 4007 2012 User Guide

3
ACCESS

Opening



)
After unlocking the vehicle using the
remote control or the key, press the
handle A
and raise the tailgate.

TAILGATE

Closing



)
Pull the handle B
downwards to
guide the tailgate,

)
release the handle and press the
exterior surface of the tailgate gently
to close it.



Emergency control

System which locks or unlocks mechan-
ically the driver's door only in the event
of a malfunction of the central locking.

Locking the driver's door


)
Insert the key in the lock, then turn it
to the left.

Unlocking the driver's door


)
Insert the key in the lock, then turn it
to the right.

Unlocking the front and rear doors
(from inside)


)
Tilt the interior control B
rearwards.


Using the key
Locking the front passenger door
and the rear doors (from inside)


)
Tilt the interior control B
forwards.

The other doors are not un-
locked.

3
ACCESS
Before opening the tailgate,
ensure that no one is within the
radius of opening.
For reasons of safety and cor-
rect operation, do not drive with
the tailgate open.
If the battery is disconnected,
the tailgate cannot be opened.
Do not climb onto the lower
tailgate and do not subject it to
heavy knocks, it may be dam-
aged.
Always close the lower tailgate
and check that it is secured cor-
rectly before closing the main
tailgate.
When closing the lower tailgate,
ensure that no person or object
is in the proximity of the moving
parts to avoid any risk of injury
or damage.
Do not open the lower tailgate
when a towbar is fi tted.
"Tailgate open" warning

This warning lamp comes on
on the instrument panel screen
when the tailgate is not closed
correctly.
LOWER TAILLGATE

Opening



)
Push the handle C
to the right and
tilt the tailgate D
gently.



Closing



)
Raise the tailgate D
, push it to close
it, then check that it is secured cor-
rectly. Maximum authorised weight on
the lower tailgate when open:
200 kg
.







Tailgate release

This enables the tailgate to be unlocked
in the event of a central locking fault.


- Fold back the rear seats to gain
access to the tailgate release from
inside the boot.

- Remove the plastic cap from the open-
ing A
in the tailgate interior pillar.

- Move the control B
to the right to
unlock and open the tailgate.

4
VISIBILITY
COURTESY LAMPTESY LAMPS
Front courtesy lamp

Map reading lamps

There are two map reading lamps, one
on each side of the courtesy lamp.
Press the corresponding lamp lens A
.

Position 2

The courtesy lamp is off, regardless of wheth-
er the doors or tailgate are open or closed.
The durations of lighting of
the front courtesy lamps can
be confi gured via the colour
screen"Equipment" menu.

Position 1
The courtesy lamp comes on when a
door or the tailgate is opened.
When the door or the tailgate is closed
again, the lighting gradually dims for a
few seconds before switching off.
However, the courtesy lamp is switched
off automatically in the following cases:


- When the doors and the tailgate
are closed and the ignition switch is
placed in the "ON"
position.

- When the doors and the tailgate are
closed and you lock the vehicle from
inside or using the remote control.

4
VISIBILITY

Rear courtesy lamp


Position 1 "ON"
The courtesy lamp is permanently on.
- When the doors and the tailgate are
closed and you lock the vehicle from
inside or using the remote control.





Boot lamp


Position 1 "ON"
The boot lamp is on, regardless of
whether the tailgate is open or closed.
Position 2 "●"
The courtesy lamp comes on when a
door or the tailgate is opened. When
the door or the tailgate is closed again,
the lighting gradually dims for a few
seconds before switching off.
However, the courtesy lamp is switched
off immediately in the following cases:


- When the doors and the tailgate
are closed and the ignition switch is
placed in the "ON"
position.
Position 3 "OFF"
The courtesy lamp is permanently off.


Position 2 "●"
The boot lamp comes on if the tailgate
is opened and switches off when the
tailgate is closed.


Position 3 "OFF"
The boot lamp is off, regardless of
whether the tailgate is open or closed.



Courtesy lamps automatic
switch off
To prevent discharging of the battery,
the courtesy lamps, map reading lamps
and boot lamp switch off automatically
after 30 minutes.
The courtesy lamps are switched on
again if the ignition switch is placed
in the "ON"
or "ACC"
position, if you
open then close a door or the tailgate or
if you use the remote control.
The duration of lighting of the
rear courtesy lamps can be con-
fi gured via the colour screen
"Equipment" menu.

7
DRIVING
REVERSING CAMERA REVERSING CAM

Linked with the navigation option, a re-
versing camera is activated automatically
when reverse gear is engaged.
The colour image is provided on the
navigation screen with indication of the
limit of the rear bumper and of the gen-
eral direction of the vehicle.
Operating fault
If an operating fault occurs, the indicator
lamp in button A
fl ashes when reverse
gear is engaged.
Contact a PEUGEOT dealer or a quali-
fi ed workshop.
In bad weather or in winter, check
that the sensors are not covered
with mud, ice or snow.

Deactivation


)
With reverse gear engaged, press
button A
, the indicator lamp goes
off, the system is fully deactivated.


Reactivation


)
With reverse gear engaged, press
button A
again, the indicator lamp
comes on, the system is reactivated.

Modifi cation of the detection zones


)
Press button A
to deactivate the
system.

)
Press button A
again for a few seconds
and release it.
The detection zone modifi cation infor-
mation is indicated by an audible signal:


- double
signal on vehicles fi tted with
a towbar,

- single
signal on vehicles which are
not fi tted with a towbar.

The red line indicates the dis-
tance required to open the lower
tailgate.

9
PRACTICAL INFORMATION

Fixing the "space-saver"
spare wheel
If your vehicle is fi tted with al-
loy wheels, it is normal to notice
that the washers do not come
into contact with the "space-
saver" spare wheel when tight-
ening the bolts on fi tting. The
wheel is retained by the conical
contact of each bolt.












Access to the spare wheel in
the 7 seat configuration
The "space-saver"
spare wheel is in-
stalled on the outside, under the boot,
supported by a metal carrier.
To gain access to the tools, refer to the
"Access to the tools" paragraph.
Putting the wheel back in place


)
Put the wheel back in place in its
carrier.

)
Lift the carrier C
and reposition the
hook D
.

)
Open the lower tailgate (refer to the
"Access" section).
)
Remove the plastic cover A
using
the handle 3
.

)
Unscrew the spare wheel carrier re-
taining bolt B
using the wheelbrace 1
.

)
Close the lower tailgate (refer to the
"Access" section).

)
Lift the carrier C
to detach the hook D

then allow it to lower.

)
Tighten the spare wheel carrier re-
taining bolt B
fully using the wheel-
brace 1
.

)
Refi t the plastic cover A
, close the
lower tailgate and store the tools.


Removing the wheel


)
Open the tailgate and the lower tail-
gate (refer to the "Access" section).

)
Take out the handle 3
(refer to the
"Access to the tools" paragraph).

9
PRACTICAL INFORMATION











Access to the spare wheel in
the 5 seat configuration
The pressed steel
spare wheel is in-
stalled on the outside, under the boot,
supported by a winch and a plastic car-
rier.
To gain access to the tools, refer to the
"Access to the tools" paragraph.

Fixing the pressed steel
spare wheel
If your vehicle is fi tted with alloy
wheels, it is normal to notice that
the washers do not come into
contact with the pressed steel
spare wheel when tightening the
bolts on fi tting. The wheel is re-
tained by the conical contact of
each bolt.

Removing the wheel


)
Open the tailgate and the lower tail-
gate (refer to the "Access" section).

)
Take out the handle 3
(refer to the
"Access to the tools" paragraph).
)
Remove the plastic cover A
using
the handle 3
.
Putting the wheel back in place


)
Put the wheel back in place in its
carrier.

)
Pass the hook C
into the chain.

)
Open the lower tailgate (refer to the
"Access" section).

)
Unscrew the retaining bolt B fully

using the wheelbrace 1
, to unwind
the winch cable.

)
Close the lower tailgate (refer to the
"Access" section).

)
Detach the hook C
from the chain.
Unwind the winch cable fully to make
unhooking of the chain easier.
)
Tighten the winch retaining bolt B

fully using the wheelbrace 1
.

)
Refi t the plastic cover A
, close the
lower tailgate and store the tools.

9
PRACTICAL INFORMATION










































Rear lamps



1.
Third brake lamp (LEDs).


2.
Brake lamps/Sidelamps
(21/5 - W21W - 5 W).


3.

Direction indicators
(WY21W - 21 W).


4.
Reversing lamps (W21W - 21 W).


5.
Number plate lamps
(W5W - 5W).


6.
Foglamps
(W21W - 21 W).


Changing brake lamp/sidelamp and
direction indicator bulbs
These two bulbs are changed from out-
side with the tailgate open:


)
Open the tailgate (refer to the "Access"
section),

)
Remove the two lamp fi xing bolts A
,

)
Extract the lamp unit from outside,
)

Turn the pin C
to the left and remove it.


)
Pull the bulb D
out and change it.
To r efi t, carry out these operations in
reverse order.

)
Turn the pin B
to the left and remove it.

)
Pull the bulb out and change it. When refi tting the lamp unit, align the
two pins E
with the openings on the ve-
hicle. Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
specifi cation and colour.

Changing the third brake lamp
(LEDs)
All work on the LED lamps must be
carried out by a PEUGEOT dealer or a
qualifi ed workshop.

9
PRACTICAL INFORMATION

Changing reversing lamp bulbs


)
Open the tailgate (refer to the "Access"
section),

)
From the inside of the tailgate, in-
sert a screwdriver in the opening on
the cover A
to use it as a lever to
open the cover.

Changing number plate lamp bulbs


)
Open the tailgate (refer to the "Ac-
cess" section) to gain access to the
number plate lamps D
,

)
Remove the lamp unit D
while
pressing it to the left.
)

Turn the pin B
to the left and remove it.


)
Pull the bulb C
out and change it.
To r efi t, carry out these operations in
reverse order.
)
Insert a thin screwdriver in the open-
ing on the lens to press the tab E
.

)
Remove the lens.

)
Pull the bulb out and change it.
To r efi t, carry out these operations in
reverse order.


)
To r efi t the lamp unit, insert the end of
the tab F
fi rst, then align the tab G
.

9
PRACTICAL INFORMATION

Changing foglamp bulbs


)
Open the tailgate and the lower tail-
gate (refer to the "Access" section)
and fold down the cover A
.

)
Remove the 4 clips B
using a screw-
driver to detach the lamp cover.

)
Remove the bolts C
and remove the
lamp unit.
)
Turn the pin and bulb assembly D
to
the left.

)
Remove the bulb.
To r efi t, carry out these operations in
reverse order.


)
When refi tting the lamp unit, align
the clips E
with the openings on the
bodywork.