display Peugeot 406 C Dag 2002 Owner's Guide

The display When the menus are used, the functions which appear at the bottom of the screen are presented in various ways: 1.Function selected.
2. Function inaccessible in this situation.
3. Function accessible.
Note: The "List" function can hold a maximum of
80 addresses.
During guidance, the screen displays different information depending on the manoeuvres to be carried out: 1. Distance to next manoeuvre.
2. Next manoeuvre to be carried out.
3. Next road to take.
4. Time.
5. Exterior temperature.
6. Current road.
7. Distance to final destination.
8. Manoeuvre to be carried out.
YOUR 406 COUPE IN DETAIL 75
87
123
654132
01-07-2002

Main menu Switch on the ignition. Press the "Menu"button to access the main menu.
Select a function using the direction arrows, then confirm ( "VAL" button). The
"Navigation/guidance" menu offers various options
for selecting guidance:
- By entering the address of a new destination,
- By selecting a service (Hotel, station, airport...) available in a town,
- By selecting an address stored in one of the two directo- ries,
- By resuming previously interrupted guidance or by stop- ping current guidance. Two messages may be displayed depending on the previous actions: "Resume guid-
ance" or "Stop guidance" ,
- Radio functions are suspended when the system is in guidance mode.
YOUR 406 COUPE IN DETAIL 77
Navigation / Guidance Following selection of the "Navigation/guidance"menu,
a screen warns you about the use of the navigation sys- tem. Follow the regulations in force and do not use theremote control while driving. Press the "VAL"button to access the next screen.
01-07-2002

Enter the name of the street. Select the "Validate"function
then press the "VAL"button.
Note: the guidance can be activated from the time the
town is entered, without the name of a street or a number.
To do this, select the "Town centre"function.
Enter the street number. Select the "Validate"function
then press the "VAL"button.
Note: the guidance can be activated as soon as the town
and street are entered, without a number. To do this, selectthe "Validate" function.
Entering a new destination The last town entered is displayed.
To enter the name of another town, select each letter using the direction arrows then confirm ( "VAL"button) for each
letter. If an error is made, the "Correct" function enables the last
letter entered to be deleted.As the name is entered, the "List"function indicates the
number of towns beginning with the same letters. If the list contains less than 5 names, these are displayed automat-
ically. Select a town then confirm ( "VAL"button).
The "Change" function enables the town entered to be
completely cleared. When the complete name of the town is displayed, select the "Validate" function then press the "VAL"button.
Note: following confirmation of a letter, only those letters
which could make up an existing name appear.
YOUR 406 COUPE IN DETAIL
78
01-07-2002

YOUR 406 COUPE IN DETAIL79
The complete destination is displayed. Select the "Vali-
date" function then press the "VAL"button.
Note: you can also change the destination or store it in one
of the two directories (see the section on storing an address in a directory). The last guidance criterion used is displayed.
Guidance begins automatically, retaining this criterion if there is no action within 5 seconds or following confirma-tion of the "NO"function.
Follow the instructions. If you wish to change the guidance criterion, select the "YES" function then press the "VAL"button. Select a criterion from the list offered then confirm (
"VAL"
button). When the criterion of your choice is selected,select the "Validate" function then press the "VAL"button.
Guidance begins, follow the instructions.
01-07-2002

YOUR 406 COUPE IN DETAIL
80
Selecting a service The last address entered is displayed. There are 3 options for defining the location in which you wish to obtain this service:
- repeat the last address entered by means of the "Vali-
date" function.
- enter the name of a new town then enter the street (or use the "Town centre" function) by means of the
"Change" function.
- automatically enter your current location by using the "Current location" function.
After confirming the address, select a service by scrolling through the list using the direction arrows then press the
"VAL" button.
A cursor on the left-hand side of the screen indicates yourposition in the list. The address of the required service is displayed. An indication on the right-hand side of the screen (e.g. 1/50) indicates whether there are any other establish-
ments (50 maximum), which offer the same service withina radius of approximately 30 miles (50 km), as the crowflies. Use the
"Next"or "Previous" functions to consult the list
offered.When the establishment of your choice is displayed, select the "Validate" function then press the "VAL"button.
Select a guidance criterion. Guidance begins, follow theinstructions.
01-07-2002

Selecting a stored destination Using the direction arrows, select the directory in which the address you are looking for is stored, then press the "VAL"
button. The stored addresses are displayed.
A cursor on the left-hand side of the screen indicates your position in the list. Select a name by scrolling through thelist using the direction arrows, then press the "VAL"but-
ton. The complete address is displayed. Select the "Vali-
date" function then press the "VAL"button. Select a guid-
ance criterion. Guidance begins, follow the instructions.
YOUR 406 COUPE IN DETAIL 81
Storing an address in a directory When a new address is entered, you can store it by select- ing the "Store" function.
Enter the name for the address. If the name already exists
for a different address, you can replace the old addresswith a new one. Select the Personal directory or the Professional directory then press the "VAL"button. The address is then stored in
the directory of your choice (storage capacity is100 addresses).
01-07-2002

YOUR 406 COUPE IN DETAIL
82
Display configuration From the general menu, the "Configure display"menu
gives access to the following parameters:
- Adjustment of the brightness and the video display
- Adjustment of the date and time.
- Selection of the language of the display and voice infor- mation (English, German, Spanish, French, Italian).
- Adjustment of the mode and units. This allows selection of the display in km/h or mph, in degrees Celsius or Fahrenheit and selection of the time format (12 or 24hour mode). Navigation options From the main menu, the
"Navigation options"menu
gives access to the following parameters:
- Management of the directories. It enables an address stored under a name to be renamed or deleted. To do this, select the directory and the name to be changed.
- Voice synthesis volume adjustment.
- Deletion of all data stored in the two directories.
01-07-2002

YOUR 406 COUPE IN DETAIL83
Guidance tools Access to the "Guidance tools" menu is by pressing the
"VAL" button during guidance.
It enables:
- the current guidance criterion to be changed,
- the programmed destination to be displayed or changed,
- the voice synthesis volume to be adjusted,
- the current guidance to be stopped.
01-07-2002

Automatic operation1 - Temperature adjustment The value requested is displayed (from 15 to 30: comfortable tempera- ture = 22).Press the up and down arrows to adjust. 2 - Automatic
comfort programme
Press the " AUTO" button. The sys-
tem automatically adjusts the tem-perature to that selected, by starting
the air conditioning if necessary. It also manages the air flow and
intake, to ensure sufficient air circu-lation inside the vehicle. Adjustment of the air distribution must be carried out manually whenyou require it.
3 - Automatic visibility programme
In certain cases, the automatic com-fort programme can prove inade-quate to de-ice or demist the win-
dows (humidity, many passengers,ice). In such cases, select the auto-
matic visibility programme to
rapidly clear the windows. The system automatically manages the air conditioning, the air flow andthe air intake, distributing the air tothe windscreen and side windows.
AUTOMATIC AIR CONDITIONING
YOUR 406 COUPE IN DETAIL
50
01-07-2002

4 - Setting the air distribution
Successive presses on the top or bottom part of thisbutton allow the air to bedirected to:
- the windscreen (de-icing or demist- ing),
- the windscreen and footwells,
- the central and side vents,
- the central and side vents and footwells,
- the footwells. Press the top or bottom part of the button to select the previous or nextsetting from the above list. Manual operation
You may, if you wish, make a differ-
ent choice from that offered by thesystem, by changing one of the set-tings. Press the "
AUTO" button to return to
automatic operation.
5 - Air conditioning
Pressing this button stops the air condi-
tioning. Pressing again returns theair conditioning to automatic opera-
tion. The symbol " A/C" is displayed.
6 - Air flow
The air flow may beincreased or reducedby pressing the '' + ''
or '' Ð'' button respectively. 7 - Air intake This button is pressed for recircu-lation of the interior
air. Recirculation, shown on the dis-
play, prevents the entry of unpleas-ant odours or fumes into the passen-ger compartment from outside.
Avoid prolonged operation of the
recirculation of interior air. A secondpress returns the system to automat-
ic intake of air. Used in humid conditions, recircula- tion risks misting up the windows.
8 - Demisting therear screen
With the engine run-ning, pressing the
switch demists the rear screen andthe mirrors.
It switches off automatically after approximately fifteen minutes. Press again to resume demisting. It is possible to stop the demisting
operation before it goes off automat-
ically, by pressing the switch again. Note: The condensation created by
air conditioning causes a normal flow of water under the vehicle when
stationary.
YOUR 406 COUPE IN DETAIL 51
01-07-2002