Peugeot 407 2004 Repair Manual

56 -
17-05-2004
57
-
17-05-2004
Automatic windscreen wipers
In the
AUTO position, the wind-
screen wipers operate automatically
and adapt their speed to the intensity
of the rainfall. Disarming
Manual operation of the wiper stalk
interrupts the
AUTO position, the de-
activation indicator light comes on on
the 5-dial instrument panel display,
accompanied by a message on the
multifunction display.
In the event of malfunction , the
windscreen wipers will operate in
intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
CHANGING A WINDSCREEN
WIPER BLADE
Placing the wiper blades in the
maintenance position
F Less than one minute after switch-
ing off the ignition, press the wind-
screen wiper stalk down once to
position the blades in the centre
of the windscreen (maintenance
position).
Replacing a blade
F Lift the arm, then unclip the blade
and remove it.
F Fit the new blade and fold down
the arm.
To park the blades, switch on the
ignition and operate the windscreen
wiper stalk.
An indicator light comes on on
the instrument panel display.
It is accompanied by a mes-
sage on the multifunction
display.
If the ignition was switched off
more than one minute ago with the
control in the AUTO position, this
function must be re-activated. To
do this, move the control to position 0
then return it to the AUTO position. Do not cover the rain sensor
located on the windscreen
behind the interior mirror.
When using an automatic car
wash, switch off the ignition or check
that the wiper stalk is not in the auto-
matic position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
Operating check
Activation
Interior comfort

58 -
17-05-2004
59
-
17-05-2004
LIGHTS
Front and rear lights (ring A)
F
Turn ring A to the position required. Lights on
With the ignition off, on opening the
driver's door a buzzer sounds to indi-
cate that you have left your lights on
although you are leaving the vehicle.
Switch the lights off.
Direction indicators (lashers)
Lights off
Side lights Dipped/main beam
headlamps
Dipped/main beam change
F Pull the stalk fully towards you. Front and rear fog lamps (ring B)
F
Turn ring B forwards to switch on
and rearwards to swich off. The
status is conirmed by the light on
the instrument panel.
Front fog lamps (one press) Left:
downwards. The
direction arrow indica-
tor light lashes on the
instrument panel.
Right: upwards. The
direction arrow indica-
tor light lashes on the
instrument panel.
Note: If you forget to return the direc-
tion indicator to its normal position,
the volume of the audible signal will
increase, if you are driving at a speed
greater than 40 mph (60 km/h).
These operate with the side lights
and the dipped or main beam head-
lamps.
Rear fog lamps (two presses)
These operate when the front fog
lamps are already on.
Interior comfort

58 -
17-05-2004
59
-
17-05-2004
Automatic switching
on of the lights
This function is active when the vehi-
cle is supplied to the customer.
The dipped beam headlamps switch
on automatically if the light is poor
and when the windscreen wipers
operate continuously. They switch off
when the light is bright enough or the
windscreen wipers stop.
Warning: in foggy weather, the bright-
ness sensor can detect suficient
light. As a consequence, the lights
will not come on automatically. Activation Manual "Follow-me-home"
lighting
When you leave your vehicle, the
side lights and dipped headlamps
can be left on for a few seconds.
Activation:
F switch off the engine,
F "lash" the headlamps,
F get out of the vehicle and lock it.
When the function is activated,
the indicator light comes on on the
5-dial instrument panel display.
To disarm or activate the func-
tion, pass via the "Personali-
sation-coniguration" menu
on your multifunction display.
For safety reasons, activation/
deactivation of the "Automatic
switching on of the lights"
function via the menu must be
carried out when stationary. To deactivate or activate
the "Automatic follow-me-
home lighting" function,
pass via the
"Person-
alisation-coniguration"
menu on your multifunc-
tion screen.
The duration of timing can
be set via the "Personalisa-
tion-coniguration" menu of
your multifunction display.
Automatic "Follow-me-home"
lighting
When you leave your vehicle with
the automatic switching on of the
lights activated, the side lights and
dipped headlamps remain on for
a few seconds after the ignition is
switched off.
Disarming
When the function is disarmed,
the indicator light comes on on the
5-dial instrument panel display.
The indicator light also comes on
when the driver uses the manual
lighting controls (temporary disarm-
ing of the function).
Do not cover the sunshine/
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
conditioning and for the automatic
switching on of the lights.
If the sunshine/brightness sensor
does not function correctly,
the side
lights and dipped headlamps and the
indicator light come on accompanied
by an audible signal and a message
on the multifunction display.
Contact a PEUGEOT dealer.
Interior comfort

58 -
17-05-2004
59
-
17-05-2004
Automatic switching
on of the lights
This function is active when the vehi-
cle is supplied to the customer.
The dipped beam headlamps switch
on automatically if the light is poor
and when the windscreen wipers
operate continuously. They switch off
when the light is bright enough or the
windscreen wipers stop.
Warning: in foggy weather, the bright-
ness sensor can detect suficient
light. As a consequence, the lights
will not come on automatically. Activation Manual "Follow-me-home"
lighting
When you leave your vehicle, the
side lights and dipped headlamps
can be left on for a few seconds.
Activation:
F switch off the engine,
F "lash" the headlamps,
F get out of the vehicle and lock it.
When the function is activated,
the indicator light comes on on the
5-dial instrument panel display.
To disarm or activate the func-
tion, pass via the "Personali-
sation-coniguration" menu
on your multifunction display.
For safety reasons, activation/
deactivation of the "Automatic
switching on of the lights"
function via the menu must be
carried out when stationary. To deactivate or activate
the "Automatic follow-me-
home lighting" function,
pass via the
"Person-
alisation-coniguration"
menu on your multifunc-
tion screen.
The duration of timing can
be set via the "Personalisa-
tion-coniguration" menu of
your multifunction display.
Automatic "Follow-me-home"
lighting
When you leave your vehicle with
the automatic switching on of the
lights activated, the side lights and
dipped headlamps remain on for
a few seconds after the ignition is
switched off.
Disarming
When the function is disarmed,
the indicator light comes on on the
5-dial instrument panel display.
The indicator light also comes on
when the driver uses the manual
lighting controls (temporary disarm-
ing of the function).
Do not cover the sunshine/
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
conditioning and for the automatic
switching on of the lights.
If the sunshine/brightness sensor
does not function correctly,
the side
lights and dipped headlamps and the
indicator light come on accompanied
by an audible signal and a message
on the multifunction display.
Contact a PEUGEOT dealer.
Interior comfort

60 -
17-05-2004
61
-
17-05-2004
HAZARD WARNING LIGHTS
Press the button, the direction indica-
tors lash.
They can operate with the ignition off.
MANUAL ADJUSTMENT
OF THE HEADLAMPS
For vehicles itted with halogen
bulbs, depending on the load in your
vehicle, adjusting the beam of your
headlamps is recommended.
0
1 or 2 people in the front seats.
- 3 people.
1 5 people.
2 5 people + maximum authorised
loads.
3 Driver + maximum authorised
loads.
Initial setting is position 0.
AUTOMATIC HEADLAMP
ADJUSTMENT
On vehicles with Xenon bulbs: the
system automatically corrects the
height of the beam, whatever the load
or speed of the vehicle. The driver is
then assured of having optimum light-
ing and not causing a nuisance to
other road users.
Automatic lighting
of hazard warning lights*
When braking in an emergency, de-
pending on the force of deceleration,
the hazard warning lights come on
automatically. They switch off automati-
cally the irst time you accelerate.
It is also possible to switch them off
by pressing the button.
* According to country. In cases of malfunction, the
warning light comes on on
the 5-dial instrument panel
display and is accompanied
by an audible signal and a message
on the multifunction display. The sys-
tem places your headlamps to the
low position.
Do not touch the Xenon bulbs. Contact
a PEUGEOT dealer.
Interior comfort

60 -
17-05-2004
61
-
17-05-2004
INSTRUMENT PANEL
LIGHTING RHEOSTAT
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the minimum (or maxi-
mum) setting, release the button then
press it again to increase (or reduce)
the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
COURTESY LIGHTS
1 - Front courtesy light
2 - Front map reading lights
With the key in the ignition on or
starting position, operate the relevant
switch. 3 - Rear courtesy light
4 - Rear map reading lights
With the key in the ignition on or
starting position, operate the relevant
switch.
The front and rear courtesy lights
come on when the ignition key is
removed, on unlocking the vehicle or
on opening one of the doors.
They gradually go off after the igni-
tion has been switched on or the
vehicle is locked.
F
Pressing switch 1 turns on the
front and rear courtesy lights.
The courtesy lights can be deacti-
vated by pressing switch 1 with the
door open. The map reading lights
are not affected by this and may be
switched on.
F To re-activate the lights, press the
switch, with the door open.
Interior comfort

62 -
17-05-2004
63
-
17-05-2004
CHANGING A BULB
Handle the bulbs with a dry cloth.
Front lights
In the engine compartment, remove
the cover secured by one or two but-
terly screws, a plastic retainer clip
and two quarter turn screws.
1 -
Dipped beam headlamps:
H1-55 W or D2S-35 W Xenon bulb.
WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be replaced by a
PEUGEOT dealer. 2 - Main beam headlamps:
H7-55 W.
F Remove the protective cover
corresponding to the faulty bulb.
F Disconnect the connector.
F Press the end of the securing
clips to free the bulb. Change the
bulb.
F When itting the new bulb, en-
sure that the direction notches
are positioned correctly and the
securing clips are ixed properly.
F Reconnect the connector.
F Reit the protective cover.
3 - Side lights: W 5 W.
F Remove the protective cover,
disconnect the connector and
then remove the bulb and
change it.
F Put the connector back in place.
F Reconnect the connector.
F Reit the protective cover. 4 - Direction indicators:
PY 21 W (amber).
F Turn the bulb holder a quarter
turn and remove it.
F Change the bulb.
Amber coloured bulbs (direction in-
dicators and side repeaters) must
be replaced with bulbs of identical
speciication and colour.
5 - Front fog lamps: H11-55 W.
Turn the wheels to full lock.
Access to the bulb is via the lap in
the front mud lap.
Contact a PEUGEOT dealer.
The headlamps are itted with poly-
carbonate glass with a protective
coating. Do not clean them with a dry
or abrasive cloth, nor with a deter-
gent or solvent product.
Ensure that the liquid used to ill the
wash-wipe and headlamp wash res-
ervoir is of good quality.
In certain climatic conditions (low
temperature, humidity), condensa-
tion on the inside surface of the
headlamp glass is normal; it disap-
pears a few minutes after the lights
are switched on.
Interior comfort

62 -
17-05-2004
63
-
17-05-2004
Direction indicator repeaters:
WY 5 W (amber).
F
Push the repeater forwards or back-
wards and release the assembly.
F Hold the connector and turn the
transparent cover a quarter turn.
F Change the bulb.
Amber coloured bulbs (direction in-
dicators and side repeaters), must
be replaced with bulbs of identical
speciication and colour.Rear lights
1 - Direction indicators: PY 21 W (amber).
2 - Brake lights/side lights: P 21/4 W.
3 - Reversing lights: P 21 W.
4 - Fog lamps/side lights: P 21/4 W.
5 - Side lights: P 21/4 W.
F Disconnect the connector.
F Unclip the two seal tabs.
F Unclip the bulb holder moving
aside the 5 tabs.
F Unscrew the bulb and change it.
F
Lock the bulb holder in place. When
reitting it, ensure that the lamp is
correctly positioned and secured.

F Reposition the two seal tabs.
F Reconnect the connector.
Third brake light: Five W 5 W bulbs.
F Remove the plastic cover care-
fully by unclipping it on either
side, perpendicular to its direction
of engagement.
F Press on the two tabs.
F Pull the red transparent cover out-
wards while maintaining the pres-
sure on the tabs.
F Change the faulty bulb.
F When reitting, ensure that the
tabs of the red transparent cover
are engaged correctly and that
the upper trim has been put back
in place correctly.
Number plate lights:
W 5 W.
F
Remove the transparent cover
using a screwdriver blade.
F Change the faulty bulb.
Interior comfort

62 -
17-05-2004
63
-
17-05-2004
Direction indicator repeaters:
WY 5 W (amber).
F
Push the repeater forwards or back-
wards and release the assembly.
F Hold the connector and turn the
transparent cover a quarter turn.
F Change the bulb.
Amber coloured bulbs (direction in-
dicators and side repeaters), must
be replaced with bulbs of identical
speciication and colour.Rear lights
1 - Direction indicators: PY 21 W (amber).
2 - Brake lights/side lights: P 21/4 W.
3 - Reversing lights: P 21 W.
4 - Fog lamps/side lights: P 21/4 W.
5 - Side lights: P 21/4 W.
F Disconnect the connector.
F Unclip the two seal tabs.
F Unclip the bulb holder moving
aside the 5 tabs.
F Unscrew the bulb and change it.
F
Lock the bulb holder in place. When
reitting it, ensure that the lamp is
correctly positioned and secured.

F Reposition the two seal tabs.
F Reconnect the connector.
Third brake light: Five W 5 W bulbs.
F Remove the plastic cover care-
fully by unclipping it on either
side, perpendicular to its direction
of engagement.
F Press on the two tabs.
F Pull the red transparent cover out-
wards while maintaining the pres-
sure on the tabs.
F Change the faulty bulb.
F When reitting, ensure that the
tabs of the red transparent cover
are engaged correctly and that
the upper trim has been put back
in place correctly.
Number plate lights:
W 5 W.
F
Remove the transparent cover
using a screwdriver blade.
F Change the faulty bulb.
Interior comfort

64 -
17-05-2004
65
-
17-05-2004
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the man-
ufacturer's servicing schedule.
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising ''service operation'' is lit.
The trip recorder display shows the
distance remaining (in round igures)
before the next service.
Example:
when switching on the
ignition and for 5 seconds, the display
shows that 900 miles/km remain
before the next service is due. Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
F
Switch off the ignition,
F Press and hold the trip recorder
re-set button,
F Switch on the ignition.
The display begins a countdown.
When the display shows "= 0", re-
lease the button; the service symbol
disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least ive
minutes, otherwise the zero re-set
will not be registered.
Once an engine oil level indication
has been displayed, the display indi-
cates the total and trip distances. If the service is overdue
, each time
the ignition is switched on and for
5 seconds, the symbol lashes.
Example: when the ignition is switched
on and for 5 seconds, the display indi-
cates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal
operation and the symbol remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user's driving habits.
Interior comfort