fuel Peugeot 407 2010 Owner's Manual

Page 2 of 249

FAMILIARISATION
Remote control key

A. Unfolding/folding the key.

B. Unlocking the vehicle
(brief press).

C.
Unlocking and partial opening of the
boot (saloon) or of the rear screen (SW)
(long press).

Also...

D. Normal locking
(a single press)
or
deadlocking of the vehicle
(two presses in succession). Fuel tank

1. Opening of the fuel fi ller fl ap.

2. Opening and hooking of the fuel
tank cap.
Tank capacity: approximately 67 litres.

A. Interior control.

B. Exterior control.

 61

 72  106
Bonnet

Page 12 of 249

FAMILIARISATION
Instrument panel

A. When the ignition is on, the fuel
gauge needle should rise.

B. When the engine is running, its as-
sociated low level warning light
should switch off.

C. When the ignition is on, the oil level
indicator should display "OIL OK"
for a few seconds.
If the levels are not correct, top up the
level which is low. Lighting of the indicator light indicates
the status of the corresponding function.
When the ignition is on, the orange and
red warning lights come on.
When the engine is running, these
warning lights should switch off.
If any warning light remains on, refer to
the page concerned.

 18

 20
 104

A. Audible front/rear parking
assistance off.

B. Central locking.

C. Interior protection alarm off.

D. Hazard warning lights.

E. Selection of the electroni-
cally controlled suspension.

F. Electronic stability pro-
gramme ESP off.
 62

 65
 86
 97

 86
Warning lights Controls bar

Page 16 of 249

1
19

1. Coolant temperature gauge.

2. Lighting on indicators:
dipped beam headlamps.
main beam headlamps.
front foglamps.
rear foglamps.

3. Rev counter dial.

4. Warning lamps:
seat belts not fastened in the front.
fuel level.
left direction indicator.

5. Fuel level gauge.
PETROL-DIESEL MANUAL AND AUTOMATICGEARBOX INSTRUMENT PANELS

10. CHECK and trip recorder zero
reset and service display button.

11. Instrument panel screen:
Total distance recorder.
Trip recorder.
Automatic gearbox lever position indicator.
Cruise control/speed limiter reference value.
Service indicator.
Navigation instructions
CHECK (vehicle autotest).
Trip computer information displays.
Warning and status displays.

12. Instrument panel lighting rheostat.

6. Warning lamps:
parking brake applied or brake fl uid level or electronic brake force
distribution fault.
right direction indicator.

7. Speedometer.

8. Warning lamps:
emission control system.
anti-lock braking system (ABS).
passenger's airbag deactivated.
pre-heat (Diesel engine starting).

9. Engine oil temperature gauge.

Page 19 of 249

1
21
Fuel warning lamp
In certain driving conditions and de-
pending on the engine, the distance
which you will be able to travel with
the remaining fuel may be less than
30 miles (50 kilometres) (the capacity
of the tank is approximately 67 litres).
Emission control system
warning lamp
This should switch off a few seconds
after the engine is switched on.
When the engine is running, if the
warning lamp fl ashes or comes on
continuously, this indicates an emis-
sion control system malfunction.
Contact a PEUGEOT dealer as soon
as possible. Diesel engine pre-heat
warning lamp
Wait for the warning lamp to switch off
before starting. The illumination period
is determined by the ambient conditions.
Passenger's airbag
deactivated warning lamp *
If the warning lamp remains on, this
indicates that the passenger's airbag
has been deactivated intentionally.
If it comes on continuously above 6 mph
(10 km/h), it indicates an ABS fault.
However, the vehicle retains conven-
tional servo-assisted braking.
Consult a PEUGEOT dealer.
Anti-lock braking system
(ABS) warning lamp
* According to country.
The warning lamp is repea-
ted on the instrument panel
screen.
When the needle is in zone
A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high.
If the coolant temperature warning
lamp comes on (linked with the STOP
warning lamp), stop as soon as it is
safe to do so.
Wait for the engine to cool down be-
fore topping up the level, if necessary.
As the cooling circuit is pressurised, in
order to prevent any risk of scalding,
unscrew the cap by two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level, if
necessary.
Consult a PEUGEOT dealer.

Page 20 of 249

1
21
Fuel warning lamp
In certain driving conditions and de-
pending on the engine, the distance
which you will be able to travel with
the remaining fuel may be less than
30 miles (50 kilometres) (the capacity
of the tank is approximately 67 litres).
Emission control system
warning lamp
This should switch off a few seconds
after the engine is switched on.
When the engine is running, if the
warning lamp fl ashes or comes on
continuously, this indicates an emis-
sion control system malfunction.
Contact a PEUGEOT dealer as soon
as possible. Diesel engine pre-heat
warning lamp
Wait for the warning lamp to switch off
before starting. The illumination period
is determined by the ambient conditions.
Passenger's airbag
deactivated warning lamp *
If the warning lamp remains on, this
indicates that the passenger's airbag
has been deactivated intentionally.
If it comes on continuously above 6 mph
(10 km/h), it indicates an ABS fault.
However, the vehicle retains conven-
tional servo-assisted braking.
Consult a PEUGEOT dealer.
Anti-lock braking system
(ABS) warning lamp
* According to country.
The warning lamp is repea-
ted on the instrument panel
screen.
When the needle is in zone
A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high.
If the coolant temperature warning
lamp comes on (linked with the STOP
warning lamp), stop as soon as it is
safe to do so.
Wait for the engine to cool down be-
fore topping up the level, if necessary.
As the cooling circuit is pressurised, in
order to prevent any risk of scalding,
unscrew the cap by two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level, if
necessary.
Consult a PEUGEOT dealer.

Page 29 of 249

1
29
Range (miles or km)
Current fuel consumption(l/100 or km/l or mpg)
This is the average quantity of fuel con-
sumed during the last few seconds.
This shows the distance that can still
be covered with the fuel remaining in
the tank in accordance with the ave-
rage consumption over the last few
miles (kilometres).
Distance remaining to be travelled (miles or km)
Average speed (mph or km/h)
TRIP menu
Press the
"MENU" button for access
to the main menu.
Select the "Trip computer" or "Ve-
hicle diagnostics" application using
the navigator, then confi rm or press
the "MODE" button until you gain ac-
cess to the trip computer screen, then
confi rm "OK" .
The "Trip computer" or "Vehicle diag-
nostics" menu offers various options:
- Alerts log,
- Status of the functions,
- Inputting the distance to be tra- velled.
Average fuel consumption(l/100 or km/l or mpg)
Distance travelled (miles or km)
Alerts log
This summarises the active warning
messages, displaying them on the
multifunction screen in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining (miles or km)
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled.
This fi gure may increase if
there is a change in the style
of driving or the road surface,
producing a signifi cant drop in
current fuel consumption.
When the range is less than 20 miles
(30 km), four bars are displayed. After
fi lling with fuel, the range is displayed
when it exceeds 62 miles (100 km).
If horizontal bars are displayed
for long periods instead of di-
gits, contact a dealer.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
This is the distance remaining to the
destination, either calculated at any
time by the navigation system if gui-
dance is activated or entered by the
user, minus the distance covered since
the distance was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last set to
zero.
This indicates the distance travelled
since the computer was last set to
zero.
Access via the main menu
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).

Page 32 of 249

2MULTIFUNCTION SCREENS
32
Display
This menu allows you to set the bright-
ness of the display, the display colour
scheme and the colour of the map
(day/night and auto mode).
Vehicle
This menu permits the activation or
deactivation of certain driving and
comfort systems:
- air conditioning (A/C),
- vehicle information,
- access to the vehicle,
- driving assistance,
- lighting confi guration,
- comfort lighting.
Units
This menu permits selection of the
units: temperature (°C or °F) and fuel
consumption (km/l, l/100, miles and
mpg).
System
This menu permits restoring of the factory
confi guration, display of the software ver-
sion and activation of scrolling text. For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done when stationary. COLOUR SCREEN (WITH PEUGEOT CONNECT NAVIGATION) "SETUP" menu
Press the SETUP button to gain access
to the "SETUP" menu. This provides
access to the following functions:
- System language,
- Date & Time,
- Display,
- Vehicle,
- Units,
- System.
System language
This menu allows you to select
the language used by the display:
German, English, Spanish, French,
Italian, Dutch, Polish, Portuguese.
Date & Time
This menu allows you to set the date
and time, the format of the date and
the format of the time (refer to the
"Audio and Telematics" section).
This displays the following information:
- time,
- date,
- ambient temperature (the value dis-
played fl ashes if there is a risk of ice),
- check of openings,
- vehicle function status messages, displayed temporarily,
- warning messages,
- audio functions,
- trip computer information,
- air conditioning settings,
- satellite navigation system information.

Page 80 of 249

4ACCESS
72
FUEL TANK
The capacity of the tank is approxi-
mately 67 litres. When the low fuel level is
reached, this warning lamp
comes on in the instrument
panel, accompanied by an au-
dible signal and a message on the mul-
tifunction screen. When it fi rst comes
on, about 6 litres of fuel remains in
the tank.
If you run completely out of fuel
(Diesel), refer also to the "Checks"
section.
A label fi tted to the inside of the fuel
fi ller fl ap indicates which type of fuel
to use.
Additions of fuel must be of at least
5 litres to be taken into account by the
fuel gauge.
Opening the fuel fi ller may produce the
noise of an inrush of air. This vacuum
is entirely normal and results from the
sealing of the fuel system.
Low fuel warning
To refuel in complete safety:

 you must switch off the engine,

 open the fuel fi ller fl ap.

 turn the cap to the left.

 remove the cap and hang the end
on the hook located on the inside
of the fl ap.

 fi ll the tank, but do not continue
after the third cut-off of the noz-
zle ; this may cause malfunctions.
After fi lling the tank:

 refi t the cap,

 close the fl ap.
Operating fault
A fuel gauge fault is indicated by the
fuel guage needle returning to zero.
Have it checked by a PEUGEOT dealer.
Refuelling

Page 81 of 249

4ACCESS
73
Special features of BioFlex
engines
A BioFlex vehicle has been designed
to run on unleaded petrol (RON 95 or
RON 98) or ethanol (this is a mixture
containing 85% ethanol and 15% un-
leaded petrol, called E85).
So, regardless of the quantity of fuel
remaining in your tank and irrespec-
tive of its type (RON 95/RON 98, E85
or a mixture of the two), you can fi ll
your tank at any time with unleaded
petrol (RON 95 or RON 98) or ethanol
(E85).
There is no problem driving on unlea-
ded petrol only with this vehicle. In winter conditions, star-
ting the engine from cold may
sometimes prove diffi cult.
During these very cold periods
you are advised to use unleaded pet-
rol rather than E85 to ensure optimum
starting conditions.
Quality of the fuel used for
petrol engines
The petrol engines are perfectly com-
patible with E10 type petrol biofuels
(containing 10% ethanol), conforming
to European standards EN 228 and
EN 15376.
E85 type fuels (containing up to 85%
ethanol) are reserved exclusively for
vehicles marketed for the use of this
type of fuel (BioFlex vehicles). The
quality of the ethanol must comply with
European standard EN 15293.
For Brazil only, special vehicles are
marketed to run on fuels containing up
to 100% ethanol (E100 type).
Quality of the fuel used for
Diesel engines
The Diesel engines are perfectly com-
patible with biofuels which conform to
current and future European standards
(Diesel fuel which complies with stan-
dard EN 590 mixed with a biofuel which
complies with standard EN 14214)
available at the pumps (containing up
to 7 % Fatty Acid Methyl Ester).
The B30 biofuel can be used in cer-
tain Diesel engines; however, this use
is subject to strict application of the
special servicing conditions. Consult a
PEUGEOT dealer.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or di-
luted, domestic fuel...) is strictly pro-
hibited (risk of damage to the engine
and fuel system).

Page 82 of 249

4ACCESS
73
Special features of BioFlex
engines
A BioFlex vehicle has been designed
to run on unleaded petrol (RON 95 or
RON 98) or ethanol (this is a mixture
containing 85% ethanol and 15% un-
leaded petrol, called E85).
So, regardless of the quantity of fuel
remaining in your tank and irrespec-
tive of its type (RON 95/RON 98, E85
or a mixture of the two), you can fi ll
your tank at any time with unleaded
petrol (RON 95 or RON 98) or ethanol
(E85).
There is no problem driving on unlea-
ded petrol only with this vehicle. In winter conditions, star-
ting the engine from cold may
sometimes prove diffi cult.
During these very cold periods
you are advised to use unleaded pet-
rol rather than E85 to ensure optimum
starting conditions.
Quality of the fuel used for
petrol engines
The petrol engines are perfectly com-
patible with E10 type petrol biofuels
(containing 10% ethanol), conforming
to European standards EN 228 and
EN 15376.
E85 type fuels (containing up to 85%
ethanol) are reserved exclusively for
vehicles marketed for the use of this
type of fuel (BioFlex vehicles). The
quality of the ethanol must comply with
European standard EN 15293.
For Brazil only, special vehicles are
marketed to run on fuels containing up
to 100% ethanol (E100 type).
Quality of the fuel used for
Diesel engines
The Diesel engines are perfectly com-
patible with biofuels which conform to
current and future European standards
(Diesel fuel which complies with stan-
dard EN 590 mixed with a biofuel which
complies with standard EN 14214)
available at the pumps (containing up
to 7 % Fatty Acid Methyl Ester).
The B30 biofuel can be used in cer-
tain Diesel engines; however, this use
is subject to strict application of the
special servicing conditions. Consult a
PEUGEOT dealer.
The use of any other type of (bio)fuel
(vegetable or animal oils, pure or di-
luted, domestic fuel...) is strictly pro-
hibited (risk of damage to the engine
and fuel system).

Page:   1-10 11-20 next >