Peugeot 407 C 2006 Owner's Guide

Instruments and controls28 -
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the man-
ufacturer’s servicing schedule.
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising "service operation" is lit.
The trip recorder display shows the
distance remaining (in round figures)
before the next service.
Example:
when switching on the ignition and
for 5 seconds, the display shows that
900 km (400 miles) remain before
the next service is due.
Once an engine oil level indication
has been displayed, the display indi-
cates the total and trip distances. If the service is overdue
, each time
the ignition is switched on and for
5 seconds, the distance and the serv-
ice spanner flash.
Example: when the ignition is
switched on and for 5 seconds, the
display indicates that the service is
overdue by 300 miles/km. The service
should be carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal
operation and the symbol remains
lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user’s driving habits.
Engine oil temperature
indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C, the
temperature is correct.
When the needle is in zone D, the
temperature is too high.
Reduce your speed to lower the tem-
perature.

Instruments and controls28 -
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the man-
ufacturer’s servicing schedule.
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising "service operation" is lit.
The trip recorder display shows the
distance remaining (in round figures)
before the next service.
Example:
when switching on the ignition and
for 5 seconds, the display shows that
900 km (400 miles) remain before
the next service is due.
Once an engine oil level indication
has been displayed, the display indi-
cates the total and trip distances. If the service is overdue
, each time
the ignition is switched on and for
5 seconds, the distance and the serv-
ice spanner flash.
Example: when the ignition is
switched on and for 5 seconds, the
display indicates that the service is
overdue by 300 miles/km. The service
should be carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal
operation and the symbol remains
lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user’s driving habits.
Engine oil temperature
indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C, the
temperature is correct.
When the needle is in zone D, the
temperature is too high.
Reduce your speed to lower the tem-
perature.

29Instruments and controls-
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
 Switch off the ignition,
 Press and hold the trip recorder
re-set button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" and
the service symbol disappears, re-
lease the button.Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 5 seconds, after the
service information.
Dipstick
There are 2 level marks
on the dipstick: never ex-
ceed level A.
In position B, top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.
A = max.
B = min.

Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
If the lack of oil is confirmed by check-
ing using the dipstick, it is imperative
that the level is topped up. Oil level gauge fault
(flashing segments)
Check the oil level using the dip-
stick.
If the level is correct, the flashing
indicates an engine oil level gauge
malfunction.
Contact a PEUGEOT dealer.
The level observed on the dipstick
is only valid if the vehicle is parked
on level ground and the engine has
been off for more than 15 minutes.
Important: after this opera-
tion, if you wish to disconnect
the battery, lock the vehicle
and wait for at least five min-
utes, otherwise the zero re-set will
not be registered.

29Instruments and controls-
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
 Switch off the ignition,
 Press and hold the trip recorder
re-set button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" and
the service symbol disappears, re-
lease the button.Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 5 seconds, after the
service information.
Dipstick
There are 2 level marks
on the dipstick: never ex-
ceed level A.
In position B, top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.
A = max.
B = min.

Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
If the lack of oil is confirmed by check-
ing using the dipstick, it is imperative
that the level is topped up. Oil level gauge fault
(flashing segments)
Check the oil level using the dip-
stick.
If the level is correct, the flashing
indicates an engine oil level gauge
malfunction.
Contact a PEUGEOT dealer.
The level observed on the dipstick
is only valid if the vehicle is parked
on level ground and the engine has
been off for more than 15 minutes.
Important: after this opera-
tion, if you wish to disconnect
the battery, lock the vehicle
and wait for at least five min-
utes, otherwise the zero re-set will
not be registered.

Instruments and controls30 -
Trip recorder zero reset
With the trip distance displayed,
press the button for a few seconds.
Distance recorder
The total distance is displayed in
zone A of the display and the trip dis-
tance in zone B.LIGHTING RHEOSTAT
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the
required brightness, release the
button.

31Instruments and controls-
TRIP COMPUTER
orTRIP: access to the
trip computer dis-
plays.
Each successive press on the but-
ton located at the end of the wipers
stalk displays different information.
- the "vehicle" tab with:
• the range and the current consumption,
- tab "1" (route 1) with:
• the average consumption, the distance travelled and the
average speed calculated over
route "1",
- tab "2" (route 2) with the same
characteristics for a second route.
Range (km or miles)
This shows the distance that can still
be covered with the fuel remaining
in the tank in accordance with the
average consumption over the last
few miles (kilometres).
This figure may increase if there is a
change in the style of driving or the
road surface, producing a significant
drop in current consumption.
When the range is less than 20 miles
(30 km), four segments are dis-
played. After filling with fuel, the
range is displayed when it exceeds
62 miles (100 km).
If horizontal segments are displayed
for long periods instead of digits,
contact a PEUGEOT dealer.
Distance remaining to be
travelled (km or miles)
This is the distance remaining to the des-
tination, either calculated at any time by
the navigation if guidance is activated or
entered by the user, minus the distance
covered since the distance was entered.
If digits are missing, dashes are dis-
played in their place.
Current consumption (l/100 or km/l or mpg)
This is the average quantity of fuel
consumed during the last few sec-
onds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
The routes
The routes "1" and "2" are independ-
ent but have identical application.
Route "1" for example allows you
to make daily calculations and route
"2" monthly calculations.
Zero reset
When the required route is displayed,
press the control for more than two
seconds.

Instruments and controls32 -
Average speed (km/h or mph)
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
Access via the general menu
"TRIP" menu
Press the "MENU" button to gain ac-
cess to the general menu.
Select the "Trip computer" applica-
tion using the navigator, then con-
firm.
The "Trip computer" menu offers var-
ious options:
- Warnings log,
- Status of the functions,
- Inputting of the distance to be travelled.
Average consumption (l/100
or km/l or mpg)
This is the average fuel consumption
since the computer was last set to
zero.
Distance travelled (km or
miles)
This indicates the distance travelled
since the computer was last set to
zero.
C colour screen.
DT 16/9 colour screen. Warnings log
This summarises the active warning
messages, displaying them on the
multifunction display in succession.
Status of the functions
This summarises the active or inac-
tive status of the functions present on
the vehicle.
Distance remaining
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled value.
Display on the instrument
panel screen
All of the various items of trip com-
puter information also appear on the
instrument panel screen at the same
time.

33Multifunction displays-
COLOUR SCREEN C
This displays the following informa-
tion, via the RD4 audio equipment
control pad:
- the time,
- the date,
- the exterior temperature (the value displayed flashes if there is a risk of
ice),
- the accesses check,
- the vehicle functions warning or status messages, displayed tem-
porarily,
- the audio sources displays,
- the trip computer displays,
- the personalisation and configura- tion displays,
- the air conditioning displays,
-
the front and rear parking assistance
display,
- the hands-free kit displays. Management of the displays
Example: "TRIP"
General menu
Press the
"MENU" button to gain
access to the general menu and
select one of the following functions:
- "Audio functions",
- "Trip computer",
- "Personalisation-Configuration",
- "Air conditioning",
- "Telephone". "Personalisation-Configuration"
menu
This provides access to successive
confirmation windows.
Defining the vehicle parameters
This enables you to activate or deactivate
certain driving and comfort elements:
- "Automatic switching on of the
lights",
- "Follow-me-home lighting" and "Duration",
- "Remote control action",
- "Permanent locking of the boot",
- "Directional headlamps".
The
"AUDIO" , "TRIP" , "CLIM"
and "TEL" buttons on the RD4
audio equipment control pad permit
displaying in the main window.
Example: "Audio functions" Example: "Automatic switching on of
the lights"

Multifunction displays34 -
Selection of the language
German, Spanish, French, English,
Italian, Dutch, Portuguese and Brazilian
Portuguese.
Configuration of the display
- "Setting the brightness-video".
- "Setting the date and time".
- "Selection of the units".
- "Selection of the colours".Changing the date and time
From the
general menu , select the
" P e r s o n a l i s a t i o n - C o n fi g u r a t i o n "
icon using the navigator, then confirm.
From the list displayed, select "Con-
figuration of the display" , then
confirm.
From the list displayed, select "Set-
ting the date and time" , then
confirm. Set the parameters one by one:
- the zone selected is displayed on
the screen,
- use the navigator to move from one zone to another,
- your new parameters are confirmed one by one, by pressing the navi-
gator button,
- all of the changes are saved, if you click on "OK" on the screen, or
cancelled, if you press the "ESC"
button on the control pad.
For safety reasons, configu-
ration of the multifunction dis-
plays by the driver must be
carried out while stationary.

35Multifunction displays-
16/9 COLOUR SCREEN DT
This displays the following informa-
tion, via the RT3 audio/telephone
control panel:
- the time,
- the date,
- the outside temperature (the value displayed flashes if there is a risk of
ice),
- the status of the accesses,
- the warning messages or vehicle function status messages, displayed
temporarily,
- the audio source displays,
- the telematic system displays (telephone, services, ...),
- the trip computer displays,
- the personalisation and configura- tion displays,
- the air conditioning displays,
-
the front and rear parking assistance
display,
- the satellite navigation system displays. General menu
Press the
"MENU" button to access
the general menu and select one of
the following functions:
- "Navigation - Traffic info",
- "Audio functions",
- "Trip computer",
- "Directory",
-
"Telephone and telematic services",- "Configuration",
- "Map",
- "Video",
- "Air conditioning". "Configuration" menu
This provides access to successive
confirmation windows.