ESP Peugeot 407 C 2008 User Guide

8
93
Gear selection gate

 Move the lever in the gate to select
a position.
The indicator light corresponding to
the position selected appears on the
instrument panel screen.

P ark: to immobilise the vehicle and to
start the engine, with the handbrake on.

R everse: to reverse (select this posi-
tion with the vehicle stationary, engine
at idle).

N eutral: to start the engine and to park,
with the handbrake on.

Note: if position N is inadvertently en-
gaged while driving, allow the engine
to return to idle before engaging posi-
tion D then accelerate.

D rive: to drive in automatic mode.

M anual: to drive selecting the gears.

S : sport programme.

 : snow programme.
'PORSCHE TIPTRONIC SYSTEM' AUTOMATIC GEARBOX
The six speed automatic gearbox of-
fers, as required, the comfort of the
auto-adaptive programme enhanced
by a selection suited to dynamic driv-
ing conditions: sport, or to driving on a
slippery road: snow.
However, manual selection is still pos-
sible using the gear lever.
Moving Off
With the engine running, move off from
position P :

 to exit position P, it is essential
to press the brake pedal,

 select position R , D or M , then
gradually release the pressure on
the brake pedal; the vehicle moves
off immediately.
To move off from position N :

 with your foot on the brake, release
the handbrake,

 select position R , D or M , then
gradually release the pressure on
the brake pedal; the vehicle moves
off immediately.
Starting the engine

 with the handbrake on, select posi-
tion P or N in the gate,

 turn the ignition key. Always keep your foot on the
brake on a steep incline.
When the engine is at idle,
brakes not applied, if posi-
tion R , D or M is selected, the vehicle
moves even without the accelerator
being pressed.

Do not leave children unsupervised
inside the vehicle, with position
R, D or M selected, with the en-
gine running, as the vehicle moves
even without the accelerator being
pressed.
With the ignition off, if the le-
ver is not in position P , an
audible signal is heard when
the driver's door is opened, or
after approximately 45 seconds. Move
the lever to position P . The audible
signal ceases.

8
96
CRUISE CONTROL/SPEED LIMITER
Selecting the function

 Place switch 1 in the CRUISE po-
sition. The cruise control is not
yet active and no speed has been
memorised. The display indicates:
Switching the function off

 Place switch 1 in position 0 or

LIMIT to switch the system off.
Note: It is possible to acceler-
ate and drive momentarily at a
speed greater than the memo-
rised speed. The value mem-
orised fl ashes. When the accelerator
pedal is released, the vehicle will re-
turn to the memorised speed.
Cancelling the memorised speed
If you wish to cancel the memorised
speed:

 Press button 4 or the brake or
clutch pedal. The display indicates
(e.g. at 70 mph (110 km/h)):
Activation/memorising a speed
As soon as you reach the chosen speed,
press button 2 or 3 . This memorises the
speed, which will be maintained auto-
matically. The display indicates (e.g. at
70 mph (110 km/h)):
On a steep descent, the cruise
control, which does not act on
the brakes, is not able to pre-
vent the vehicle from exceed-
ing the programmed speed.
In no circumstances does the cruise
control replace the requirement to re-
spect speed limits, nor does it replace
the need for vigilance and responsibil-
ity on the part of the driver.
We recommend that your feet remain
near the pedals.
Cruise control function
This enables the vehicle to maintain a
steady speed programmed by the driver
In order for it to be memorised, the
vehicle speed must be greater than
25 mph (40 km/h) with at least fourth
gear engaged (second gear for the
automatic gearbox), with the engine
running .

8
Note: the speed memorised
is cancelled automatically if
the vehicle speed is less than
25 mph (40 km/h), or if the
manual gearbox is in a gear lower than
fourth (second gear for the automatic
gearbox) or if the ESP is activated. Operating check
In the event of a cruise control malfunc-
tion, the memorised speed is erased,
the dashes fl ash for a few seconds:
Contact a PEUGEOT dealer to have
the system checked.
Do not use the cruise control
on slippery roads or in heavy
traffi c.
Changing a memorised speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:

 press button 3 ;
Using the accelerator:

 exceed the memorised speed until
the required speed is reached,

 press button 2 or 3 .
Recalling the memorised speed
After cancellation, press button 4 . Your
vehicle will return to the last memo-
rised speed. The display indicates
(e.g. at 70 mph (110 km/h)):
Cancelling the memorised speed

 Place switch 1 in position 0 or

LIMIT or switch off the ignition.
To memorise a speed lower than the
previous one:

 press button 2 ;
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly,
-
never fi t one mat on top of another.
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)

Maintained press: continuous increase or
decrease of the value in steps of 5 mph
(5 km/h).

8
98
CRUISE CONTROL/SPEED LIMITER
Selecting the function

 Place switch 1 in the LIMIT posi-
tion. The limiter is not yet active.
By default the display indicates:
Switching the function off

 Place switch 1 in position 0 or

CRUISE or switch off the ignition
to switch the system off. The last
speed programmed remains in the
memory.
Memorising a speed
A speed can be memorised without
activation of the limiter.
Pressing buttons 2 and 3 decreases or
increases the speed.
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)
Maintained press: continuous increase or
decrease of the value in steps of 5 mph
(5 km/h).
Activation/deactivation of the
limiter
Pressing button 4 activates the limiter,
pressing this button again deactivates it.
When the limiter is active, the display
indicates (e.g. at 70 mph (110 km/h)):

The operations must be carried
out with the engine running.
On a steep descent or if the
driver accelerates sharply, the
speed limiter, which does not
act on the brakes, is not able
to prevent the vehicle from exceeding
the programmed speed.
In no circumstances does the speed
limiter replace the requirement to re-
spect speed limits, nor does it replace
the need for vigilance and responsibil-
ity on the part of the driver.
The driver must remain vigilant and
stay in complete control of his vehicle.
Limiter function
This prevents the vehicle speed ex-
ceeding the speed programmed by
the driver (minimum speed of 18 mph
(30 km/h)).

8
102
TYRE UNDER-INFLATION DETECTION
Sensors check the tyre pressure dur-
ing driving and trigger a warning in the
event of malfunction.
Pressure Check
With the ignition on and the ve-
hicle having been stationary
for approximately 15 minutes,
and after the engine oil level,
this indicator light comes on
on the instrument panel screen to indi-
cate that the system is measuring the
tyre pressures.
Pressure OK
This indicator light comes
on on the instrument panel
screen if all of the tyre pres-
sure values measured are
correct.
If this indicator light does not appear,
contact a PEUGEOT dealer to have
the system checked. Puncture
This warning light, accom-
panied by the audible sig-
nal and the message on the
multi-function display locat-
ing the wheel concerned, is
followed by illumination of the STOP
warning light.
Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged wheel (punc-
tured or very defl ated tyre), and have
the tyre pressure checked as soon as
possible.

Note: this message is also
displayed when one of the
wheels is away from the ve-
hicle (being repaired) or when
one or more wheels without a
sensor are fi tted. All repairs and changing of
tyres on a wheel fi tted with this
system must be carried out by
a PEUGEOT dealer.
If, when changing a tyre, you install a
wheel which is not detected by your
vehicle, you must have the system
reinitialised by a PEUGEOT dealer.
The tyre under-infl ation detection sys-
tem is an aid to driving which does not
replace the need for the driver to be
vigilant or to drive responsibly.
This system does not eliminate the
need to have the tyre pressure checked
regularly (see manufacturer's label) to
ensure that the optimum dynamic per-
formance of the vehicle is maintained
and prevent premature wear of the
tyres, particularly in arduous driving
conditions (heavy load, high speed).

The tyre pressures must be checked
cold, at least once a month. Remember to
check the pressure of the spare wheel.
The tyre under-infl ation detection sys-
tem may experience temporary inter-
ference due to radioelectric emissions
on a frequency close to that used by
the system.
Flat tyre This warning light is accom-
panied by the audible signal
and the message on the mul-
ti-function display locating
the wheel concerned.
If this warning light comes on, have
the tyre pressure checked as soon as
possible. Sensor(s) not detected or faulty
This warning light is accom-
panied by the audible sig-
nal and the message on the
multi-function display which
indicates that under-infl ation
detection is absent from one (or sev-
eral) wheel(s) or that there is a fault in
the system.
Contact a PEUGEOT dealer to replace
the faulty sensor(s).

1010
114
CHANGING A FUSE
The fuse boxes are placed in the glove
box (passenger side), in the engine
compartment (left-hand side) and in
the left boot trim.
Fascia fuses
To access the fuses, open the glove
box and tilt the fuse box lid.
Replacing a fuse
Before replacing a fuse, the cause of
the incident must be found and recti-
fi ed. The fuse numbers are indicated
on the fuse box. Always replace a faulty fuse
with a fuse of the same rating
(same colour). Use the special pliers located on the
support next to the fuse box, this sup-
port also contains the replacement
fuses.

Fuse N° Rating Functions

G29 - Not used.

G30 5 A Heated rear screen.

G31 5 A Tyre under-infl ation detection, CD changer.

G32 - Not used.

G33 5 A Power steering electropump unit, dual-function
brake switch.

G34 5 A Dual-function brake switch, automatic gearbox r elay.

G35 5 A
Steering wheel angle sensor and ESP gyrometer sens or.

G36 25 A Hi-Fi amplifi er.

G37 15 A Automatic gearbox.

G38 20 A Heated seats.

G39 30 A Passenger seat memory unit.

G40 30 A Driver's seat memory unit.

1010
114
CHANGING A FUSE
The fuse boxes are placed in the glove
box (passenger side), in the engine
compartment (left-hand side) and in
the left boot trim.
Fascia fuses
To access the fuses, open the glove
box and tilt the fuse box lid.
Replacing a fuse
Before replacing a fuse, the cause of
the incident must be found and recti-
fi ed. The fuse numbers are indicated
on the fuse box. Always replace a faulty fuse
with a fuse of the same rating
(same colour). Use the special pliers located on the
support next to the fuse box, this sup-
port also contains the replacement
fuses.

Fuse N° Rating Functions

G29 - Not used.

G30 5 A Heated rear screen.

G31 5 A Tyre under-infl ation detection, CD changer.

G32 - Not used.

G33 5 A Power steering electropump unit, dual-function
brake switch.

G34 5 A Dual-function brake switch, automatic gearbox r elay.

G35 5 A
Steering wheel angle sensor and ESP gyrometer sens or.

G36 25 A Hi-Fi amplifi er.

G37 15 A Automatic gearbox.

G38 20 A Heated seats.

G39 30 A Passenger seat memory unit.

G40 30 A Driver's seat memory unit.

1010
Engine compartment fuses
To access the fuses located in the
engine compartment (next to the bat-
tery), remove the battery cover and
unclip the fuse box cover.
Close the fuse box cover carefully and
refi t the battery cover when you have
fi nished.
Fuse N° Rating Functions

1 20 A Engine control unit, fan assembly relay supply.

2 15 A Horn.

3 10 A Wash-wipe pump.

4 20 A Headlamp wash pump.

5 15 A Fuel pump, engine management actuators
(air fl ow sensor, solenoid valves, ...).

6 10 A ESP control unit.

7 10 A Automatic headlamp adjustment.

8 20 A Starter coil.

1010
117
The electrical system of your
vehicle is designed to oper-
ate with standard or optional
equipment.
Before installing other electrical equip-
ment or accessories on your vehicle,
contact a PEUGEOT dealer. PEUGEOT will not accept responsi-
bility for the cost incurred in repairing
your vehicle or for rectifying the mal-
functions resulting from the installation
of accessories not supplied and not
recommended by PEUGEOT and not
installed in accordance with its instruc-
tions, in particular where the equip-
ment in question consumes more than
10 milliamperes. The maxi-fuses provide additional
protection for the electrical systems.
All work must be carried out by a
PEUGEOT dealer.
Fuse N°RatingFunctions
910 A Directional headlamps control unit, additional heating sw
itching and protection control unit, clutch switch.
1030 A Engine management actuators (ignition coil, injectors, thermosta ts, solenoid valves, oxygen sensors), diesel additive pump, fuel pump, engine control unit, Blow-by heater.
1140 A Air conditioning blower.
1230 A Windscreen wipers.
1340 A Built-in systems interface supply (ignition positive).
1430 A Not used.

11
22
11
33
22
148
Press the MENU button then select the CONFIGURATION function, then SOUNDS, then ACTIVATE AUXILIARY SOURCE to acti vate the auxiliary input of the WIP Com audio and telematics system.
Connect the portable equipment (MP3 player…) to the audio sockets (white and red, RCA type) located in the glove box using a JACK/RCA audio cable.
Press the SOURCE button several times in succession and select AUX.
PLAYING A CD (NOT MP3 COMPATIBLE)
Insert one or more CDs in the changer. Press the SOURCE button several times in succession and select CD CHANGER.
Press one of the buttons on the alphanumeric keypad to select the corresponding CD.
Press one of the buttons to select a track on the CD.
The displaying and management of the commands take s place via the portable equipment.
It is not possible to copy the fi les onto the hard disc from the auxiliary input.
It is not possible to copy the fi les onto the hard disc from the CD changer.
JACK/RCA AUDIO CABLE NOT SUPPLIED
CD CHANGER USING THE AUXILIARY INPUT (AUX)