Heat Peugeot 407 C 2008 Owner's Manual

1. Audio equipment steering wheel
control.

2. Steering lock and ignition.

3. Wipers/wash-wipe and trip
computer controls.

4. Instrument panel.

5. Driver's air bag.
Horn.

6. Gear lever.

7. Driver's seat electric controls.

8. Driver's heated seat control.

9. Driver's footwell air outlet.

10. Storage compartment.

11. Fuel fi ller fl ap opening button.

12. Adjustable and closing side vent.

13. Speakers (tweeters).

14. Disarming of the passenger airbag *

1. Steering wheel height and depth
adjustment.

2. Cruise control/
speed limiter switches.

3. Lights and direction indicators
controls.

4. Speakers (tweeters).

5. Adjustable and closing central
vents.

6. Air diffuser vent grille.

7. Windscreen de-icing and demisting
vent.

8. Sunshine sensor.

9. Adjustable and closing side vent.

10. Bonnet release.

11. Passenger air bag.

12. Glove box/Video sockets.
Fascia fuse box.

13. Passenger footwell air outlet.

14. Passenger heated seat control.

15. Passenger seat electric controls.
* According to country.

1
20

1. Coolant temperature indicator dial.

2. Lights on indicators:
dipped headlamps.
main beam headlamps.
front fog lamps.
rear fog lamps.

3. Rev counter dial.

4. Warning lights:
seat belts not fastened in the front.
fuel level.
left direction indicator.

5. Fuel level indicator dial.
5 - DIAL PETROL-DIESEL MANUAL AND AUTOMATIC GEARBOX INSTRUMENT PANELS

10. CHECK and trip recorder zero re-
set and service display button.

11. Instrument panel display:
Total distance recorder.
Trip recorder.
Cruise control/ speed limiter refer- ence value.
Service indicator.
Direction advice (navigation)
CHECK (vehicle autotest).
Trip computer information displays.
Warning and status displays.

6. Warning lights:
handbrake applied or brake fl uid level or electronic brake force dis-
tribution fault.
right direction indicator.

7. Speedometer dial.

8. Warning lights:
emission control system.
anti-lock braking system (ABS).
passenger air bag disarmed.
pre-heat (Diesel engine starting).

9. Engine oil temperature indicator
dial. Automatic gearbox lever position
indicator.

12. Instrument panel lighting rheostat.

1
23
Braking system warning
light
This indicates:
- handbrake applied or incorrectly released,
- an excessive drop in the brake fl u- id level, in this case linked with the

STOP warning light,
- an electronic brake force distribu- tion malfunction, linked with the

STOP warning light.
WARNING LIGHTS WHICH ARE DISPLAYED ON THE INSTRUMENT PANEL
Seat belt warning light
When the ignition is switched
on, the warning light comes
on if a front occupant has not
fastened his seat belt or if he
unfastens it.
Fuel warning light
In certain driving conditions
and depending on the en-
gine, the distance which you
will be able to travel with
the remaining fuel may be less than
30 miles (50 kilometres) (the capacity
of the tank is approximately 67 litres).
Emission control system
warning light
This should switch off a few
seconds after the engine is
switched on.
When the engine is running, if the
warning light fl ashes or comes on con-
tinuously, this indicates an emission
control system malfunction.
Contact a PEUGEOT dealer as soon
as possible. Passenger air bag
disarmed warning light *
If the warning light remains
on, this indicates that the
passenger air bag has been
disarmed intentionally.
This warning light is re-
peated on the instrument
panel screen in the case
of the last 2 faults.

Stop immediately in the two latter
cases. Consult a PEUGEOT dealer. Anti-lock braking system
(ABS) warning light
If it comes on continuously
above 6 mph (10 km/h), it in-
dicates an ABS fault.
However, the vehicle retains conven-
tional servo-assisted braking.
Consult a PEUGEOT dealer.
This warning light is re-
peated on the instrument
panel screen.
Directional headlamps
warning light
When this fl ashes, it indi-
cates a malfunction of the
directional headlamps.
Consult a PEUGEOT dealer. Diesel engine pre-heat
warning light
Wait for the warning light to
switch off before starting.
The duration of the display
is determined by the exterior
climatic conditions.
This warning light is re-
peated on the instrument
panel screen.
* According to country.

3
43
Deactivation of the air conditioning
(A/C-OFF)
Deactivation or activation of the
simultaneous Left-Right control
Activation of this function permits the
transfer of the driver's confi guration to
the passenger.
Deactivation of this function permits a
return to the independent driver/pas-
senger settings.
Any manual action on button 4 or 6
cancels the simultaneous confi gura-
tion setting.
"AIR CON" menu
Press the "MENU" but-
ton to gain access to
the general menu, then
confi rm.
The "General menu" appears on the
multifunction display.
Select the Air Conditioning icon using
the navigator buttons.
The "Air Conditioning" menu ap-
pears on the multifunction display as
the main display.
Additional heating *
Vehicles which are fi tted with an HDI
engine may be equipped with auto-
matic additional heating to improve
your comfort.
When the engine is idling or when the
vehicle is stationary, a high-pitched
whistling noise and the emission of a
small amount of smoke and odour is
normal.
* According to country.
Deactivation may result in discomfort
(temperature, humidity, odour, con-
densation).
You can cancel the deactivation by
pressing the
"AUTO" button on the air
conditioning control panel.

3
44
PROGRAMMABLE HEATING Programming remote control
The heating system programming re-
mote control consists of the following
buttons and displays:

1. Scrolling functions menu buttons.

2. Function indicator lights: clock,
temperature, operating time, pro-
grammed time, heater operation,
heating management symbols.

3. Digital displays: time, temperature,
duration of operation, programmed
time or level of heating.

4. Off button.

5. On button.
Displaying the functions

If a malfunction of the programma-
ble heating system occurs, contact
a PEUGEOT dealer.
The programmable heating operates
independently of the engine.
When the engine is off, it pre-heats
the coolant circuit in order to benefi t
from an optimum engine operating
temperature from the time the engine
is switched on.
The programmable heating system
is switched on using the long range
remote control. Activation can be im-
mediate or deferred by means of a
programming function.
screen
Press the buttons
1 in succession to
display the functions.
The fi rst press of the left-hand or right-
hand button displays the time.
Next, the left-hand button permits ac-
cess to the programming time then to
the level of heating (C1 to C5).
The right-hand button permits access
to the passenger compartment tem-
perature then to the duration of opera-
tion of the heater if it is to be switched
on immediately.
The passenger compartment
temperature information is only
available when the engine is off.

3
46
You must programme your departure
time in order for the system to calcu-
late the optimum heater start time au-
tomatically.
Programming the heating
Set the time by pressing the buttons 1
and press buttons 4 and 5 simultane-
ously to save it.
Programming the departure time
Press the buttons
1 to display the pro-
gramming time.
This symbol is displayed.
Once the programming time has been
displayed, press buttons 4 and 5 si-
multaneously within 10 seconds.
This symbol fl ashes.
This symbol is displayed (fi xed). Once the programming time has been
displayed by means of the buttons
1 ,
press button 5 (ON) until the message

"OK" appears.
Activation - deactivation
When the signal has been received,
the message
"OK" is displayed
along with the symbol "HTM" .
To deactivate the programming, press
button 5 (OFF) until the message

"OK" appears.
HTM: Heat Thermo Management.
The symbol "HTM" is switched off.
When carrying out these opera-
tions, if the message "FAIL" ap-
pears, the signal has not been
received. Repeat the procedure
after changing your location.
This symbol is displayed when
the heater starts.
Switching off the heating
Press button
5 (ON).
The symbol "HTM" remains on.
Changing the level of heating
The system offers 5 levels of heating
(from the lowest level C1 to the high-
est level C5 ).
Once the level of heating has been
displayed by means of the buttons 1 ,
press buttons 4 and 5 simultaneously.
The letter "C" fl ashes.
Set the level of heating by pressing
the buttons 1 .
Press buttons 4 and 5 simultaneously
to save the level selected. The letter

"C" is displayed (fi xed).
The factory pre-sets are re-
placed by the new settings en-
tered. The programmed times
are stored until the next time
they are changed.
When the departure time is acti-
vated, the level of heating cannot be
changed. The departure time must be
deactivated fi rst.

3
Always switch off the programmable
heating while fi lling with fuel to avoid
any risk of fi re or explosion.
To avoid any risk of poisoning and as-
phyxiation, the programmable heat-
ing must not be used, even for short
periods, in an enclosed space such
as a garage or workshop which is not
equipped with an exhaust gas extrac-
tion system.
Do not park the vehicle on an infl am-
mable surface (dry grass, dead leaves,
paper…), there is a risk of fi re.
The programmable heating system
is supplied by the vehicle's fuel tank.
Before use, ensure that the quantity of
fuel remaining is suffi cient. If the fuel
tank is at the reserve, we strongly ad-
vise that you do not programme the
heating.
Changing the battery
The remote control is supplied by a
6 V-28 L battery, which is supplied.
Information on the display indicates
when it is time to replace this battery.
Unclip the casing then replace the bat-
tery.
The remote control must then be reini-
tialised, see below.
Do not discard the used batteries, take
them to an approved collection point. Reinitialising the remote
control
If the vehicle's battery is dis-
connected or the remote con-
trol's battery is replaced, the remote
control must be reinitialised.
After switching on the power, press
button 4 (OFF) for 1 second within the
next 5 seconds. If the operation has
taken place correctly the message

"OK" is displayed on the remote con-
trol screen.
If a problem occurs, the message

"FAIL" appears. Repeat the operation.
As an accessory, your programmable
heating can be adapted to pre-heat
your vehicle's passenger compartment.

3
53
Heated seat adjustment
With the engine running, turn the knob.
The temperature of the seat is regu-
lated automatically.

0: Off.

1: Low.
2: Medium.

3: High.
Driver and passenger seat lumbar
adjustment *
Operate the lever to obtain the re-
quired position.
Access to the rear seats
If necessary, detach the seat belt from
the handle and position it along the
door pillar.
Pull the handle
A upwards and for-
wards to fold the seat back, then move
the seat forward pushing the seat
back.
The driver has a courtesy handle B
to enable him to move the passenger
seat from his seat.
When it is put back in place, the seat
returns to its initial position. No person or object must
prevent the seat from returning
to its initial
longitudinal and

angle position.
Depending on your seat’s settings, it
is possible that the access to the rear
seats manoeuvre may be limited. In
this case, the seat settings must be
altered fi rst.
The seat must return to this position
for correct locking of the seat back.
Ensure that the seat back returns to its
position correctly and never drive with
the seat back disengaged (free of any
movement).
If the seat back jams on repositioning,
operate the handle A again to release
it and return it to its initial position.
* With electric seat only.
Do not use the seat back an-
gle adjustment control when
using the access to the rear
seats (risk of disengaging of
the seat back with loss of the angle
adjustment function).

3
53
Heated seat adjustment
With the engine running, turn the knob.
The temperature of the seat is regu-
lated automatically.

0: Off.

1: Low.
2: Medium.

3: High.
Driver and passenger seat lumbar
adjustment *
Operate the lever to obtain the re-
quired position.
Access to the rear seats
If necessary, detach the seat belt from
the handle and position it along the
door pillar.
Pull the handle
A upwards and for-
wards to fold the seat back, then move
the seat forward pushing the seat
back.
The driver has a courtesy handle B
to enable him to move the passenger
seat from his seat.
When it is put back in place, the seat
returns to its initial position. No person or object must
prevent the seat from returning
to its initial
longitudinal and

angle position.
Depending on your seat’s settings, it
is possible that the access to the rear
seats manoeuvre may be limited. In
this case, the seat settings must be
altered fi rst.
The seat must return to this position
for correct locking of the seat back.
Ensure that the seat back returns to its
position correctly and never drive with
the seat back disengaged (free of any
movement).
If the seat back jams on repositioning,
operate the handle A again to release
it and return it to its initial position.
* With electric seat only.
Do not use the seat back an-
gle adjustment control when
using the access to the rear
seats (risk of disengaging of
the seat back with loss of the angle
adjustment function).