remote start Peugeot 407 C 2008 Owner's Manual

4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL

 Switch off the ignition.

 Switch the ignition on again.

 Press the remote control locking but-
ton immediately for a few seconds.

 Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is rec-
ognised and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
If the system does not
function correctly , the
warning light comes on on
the instrument panel display,
accompanied by an audible
signal and a message on the
multifunction display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work af-
ter the battery has been changed, re-
programme the remote control.

4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL

 Switch off the ignition.

 Switch the ignition on again.

 Press the remote control locking but-
ton immediately for a few seconds.

 Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is rec-
ognised and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
If the system does not
function correctly , the
warning light comes on on
the instrument panel display,
accompanied by an audible
signal and a message on the
multifunction display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work af-
ter the battery has been changed, re-
programme the remote control.

4
66
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the cas-
ing using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL

 Switch off the ignition.

 Switch the ignition on again.

 Press the remote control locking but-
ton immediately for a few seconds.

 Switch off the ignition and remove
the remote control key from the ig-
nition lock. The remote control is
now working again.
ELECTRONIC ENGINE IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre-
vents starting of the vehicle by anyone
who does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code is rec-
ognised and starting is possible.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point.
If the system does not
function correctly , the
warning light comes on on
the instrument panel display,
accompanied by an audible
signal and a message on the
multifunction display.
In this case, your vehicle will not start.
Contact a PEUGEOT dealer as soon
as possible.
If the remote control does not work af-
ter the battery has been changed, re-
programme the remote control.