ECO mode Peugeot 407 C 2010.5 Owner's Manual

Page 81 of 243

4
72
SUNROOF

To tilt the roof: press and hold part A
of the switch.

To open the roof in sliding mode: tilt
the sunroof, then press part A of the
switch briefl y.

To close it in sliding mode: press
part B of the switch briefl y.

To close it in tilt mode: press and
hold part B of the switch.
Safety anti-pinch
When the sunroof is sliding closed and
meets an obstacle, it stops then par-
tially opens again. Pressing the locking button
on the remote control key for
more than 2 seconds closes
the sunroof in sliding mode.
The sunroof remains tilted.
To close the sunroof completely, press
and hold part B of the switch before
getting out of the vehicle.
Always remove the key from
the ignition when leaving the
vehicle, even for a short time.
Always ensure that the sun-
roof is closed correctly before leaving
the vehicle.
In the event of contact during closing in tilt mode, you must reverse the move-
ment of the roof. To do this, press the
switch concerned.
When the driver closes the roof in tilt
mode, they must ensure that no one is
preventing correct closing of the roof.
The driver must ensure that the pas-
sengers use the sunroof correctly.
Be aware of children when operating
the roof.
Notes:

In the event of unwanted opening of
the roof on closing (for example, in the
presence of ice), press and hold part
B
of the switch, within the two seconds
which follow the triggering of the safe-
ty anti-pinch, until the sunroof closes
completely.
Following reconnection of the bat-
tery or in the event of a malfunction,
press and hold part B of the switch,
the sunroof slides "step by step" until
it closes. Continue to press the switch
for approximately one second after
closing.

The safety anti-pinch function is not
active during these operations.
Blind
The sunroof blind is manual.
To open it, slide it rearwards using the
handle.
To close it, slide it forwards using the
handle.

Do not open the sunroof immedi-
ately after a shower or immediately
after washing the car.

Page 134 of 243

1010
119
CHANGING A WINDSCREEN WIPER BLADE
ECONOMY MODE FUNCTION
After the engine has stopped, certain
electrical functions can be used for a
maximum duration of approximately
one hour, to prevent discharging of the
battery.
LOAD REDUCTION FUNCTION
When driving, certain functions (air
conditioning, heated rear screen,
heating system for passenger com-
partment of Diesel vehicles, etc.) may
be switched off temporarily, depending
on the level of battery charge.
Reactivation of these functions is au-
tomatic, once the battery charge is
suffi cient.
Note: at the risk of discharg-
ing the battery, the functions
that have been switched off
may be reactivated manually.

Note : if the telephone is being
used when economy mode
starts, it will still be possible to
fi nish the call.
A fl at battery prevents the en-
gine from starting.
Replacing a blade

 Lift the arm, then unclip the blade
and remove it.

 Fit the new blade and fold down
the arm.
To reposition the blades, switch on the
ignition and operate the windscreen
wiper stalk. Once the hour is over, a switching to
economy mode message appears in
the multifunction scren and the active
functions are put on standby.
These functions are reactivated au-
tomatically next time the vehicle is
driven.
In order to resume the use of these
functions immediately, the engine
must be started and left to run for a
few minutes.
The time available to you will then be
approximately double the duration
for which the engine is left running.
However, this period will always be
between fi ve and thirty minutes.
This time may be signifi cantly
reduced if the battery charge
is low.
Placing the wiper blades in the
maintenance position

 Less than one minute after switching
off the ignition, press the windscreen
wiper stalk down once to position the
blades vertically on the windscreen
(maintenance position).