PEUGEOT 407 DAG 2004 Owners Manual

134 -
11-10-2004
135
-
11-10-2004
Fitting a wheel
F
Position the wheel using the
centralising tool to assist you.
F Tighten the bolts by hand and
remove the centralising tool.
F Partly tighten the bolts using the
wheelbrace.
F Fold the jack and remove it.
F Fully tighten the bolts using the
wheelbrace.
F For vehicles with steel wheels,
reit the wheel trim starting by
placing its notch facing the valve
and press with the palm of the
hand.
F For vehicles with alloy wheels,
reit the trim covers. Punctured tyre warning
light
Information on the instrument
panel:
F
Put the tool holder back in posi-
tion. This helps to keep the boot
loor in its correct position, to pre-
vent any deformation of the loor
when loaded.
F Tighten the spare wheel securing
strap to prevent noise and for your
safety in the event of impact.
Reminder: for your safety, always
change a wheel:
- on level, stable, non-slippery ground,
- with the handbrake applied,
- with irst or reverse gear engaged (position P for the automatic gear-
box),
- never go underneath a vehicle which is supported only by a jack. Tyre under-inlation
detection system warning
light
These original wheels are itted with
a pressure sensor (see paragraph
"Tyre under-inlation detection"). The
alarm which detects the removal or
absence of a wheel itted with the
indicator sensor signals the anom-
aly. Have the wheel repaired and
checked by a PEUGEOT dealer.
After changing the wheel:
- have the tightening of the bolts and the tyre pressure of the spare wheel
checked as soon as possible.
- have the punctured wheel repaired and reit it to the vehicle as soon as
possible.
- have the spare wheel checked and replace it in its boot recess.
407 saloon and 407 SW comfort

134 -
11-10-2004
135
-
11-10-2004
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use tool
6 to remove the trims before
slackening the bolts. Fitting the spare wheel
If your vehicle is itted with a steel
spare wheel, when itting it, it is
normal
when tightening the bolts to
notice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt.
Fitting snow tyres
If you it snow tyres mounted on steel
wheels onto your vehicle, it is es-
sential to use special bolts available
from your PEUGEOT dealer.
PARTIAL REMOVABLE
CLOSER*
The partial removable closer is a
cover which is clipped onto the air
intake grille to prevent the accumula-
tion of snow due to direct splashes.
Once it has been itted on your vehi-
cle, it is imperative that it is removed
when the ambient temperature con-
ditions rise above 10 °C again.
Contact a PEUGEOT dealer.
Tyres of size 215/55 R 17
cannot be itted with stand-
ard snow chains, contact a
PEUGEOT dealer.
* According to country.
Special features of alloy
wheels
Anti-theft bolts
Your wheels are itted with anti-
theft bolts (one per wheel), placed
under chrome trims which must be
removed using tool 6, before the
bolts are unscrewed using one of the
two anti-theft sockets and the wheel
brace 1.
Note: these anti-theft sockets were
given to you on delivery of your
vehicle with the duplicate keys and
the conidential card. Make a careful
note of the code number engraved
on the head of the anti-theft socket.
This will enable you to obtain a
duplicate anti-theft socket from a
PEUGEOT dealer. You are advised
to do the same for the duplicate keys
and not to leave the conidential card
in the vehicle.
407 saloon and 407 SW comfort

134 -
11-10-2004
135
-
11-10-2004
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use tool
6 to remove the trims before
slackening the bolts. Fitting the spare wheel
If your vehicle is itted with a steel
spare wheel, when itting it, it is
normal
when tightening the bolts to
notice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt.
Fitting snow tyres
If you it snow tyres mounted on steel
wheels onto your vehicle, it is es-
sential to use special bolts available
from your PEUGEOT dealer.
PARTIAL REMOVABLE
CLOSER*
The partial removable closer is a
cover which is clipped onto the air
intake grille to prevent the accumula-
tion of snow due to direct splashes.
Once it has been itted on your vehi-
cle, it is imperative that it is removed
when the ambient temperature con-
ditions rise above 10 °C again.
Contact a PEUGEOT dealer.
Tyres of size 215/55 R 17
cannot be itted with stand-
ard snow chains, contact a
PEUGEOT dealer.
* According to country.
Special features of alloy
wheels
Anti-theft bolts
Your wheels are itted with anti-
theft bolts (one per wheel), placed
under chrome trims which must be
removed using tool 6, before the
bolts are unscrewed using one of the
two anti-theft sockets and the wheel
brace 1.
Note: these anti-theft sockets were
given to you on delivery of your
vehicle with the duplicate keys and
the conidential card. Make a careful
note of the code number engraved
on the head of the anti-theft socket.
This will enable you to obtain a
duplicate anti-theft socket from a
PEUGEOT dealer. You are advised
to do the same for the duplicate keys
and not to leave the conidential card
in the vehicle.
407 saloon and 407 SW comfort

136 -
11-10-2004
137
-
11-10-2004
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
Front lights
In the engine compartment, remove
the cover secured by one or two but-
terly screws, a plastic retainer clip
and two quarter turn screws.
1 - Dipped beam headlamps:
H1-55 W or D2S-35 W Xenon
bulb.
WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be replaced by a
PEUGEOT dealer. 2 - Main beam headlamps:
H7-55 W.
F Remove the protective cover cor-
responding to the faulty bulb.
F Disconnect the connector.
F Press the end of the securing
clips to free the bulb. Change the
bulb.
F When itting the new bulb, ensure
that the direction notches are
positioned correctly and the se-
curing clips are ixed properly.
F Reconnect the connector.
F Reit the protective cover.
3 - Side lights: W 5 W.
F Remove the protective cover, dis-
connect the connector and then
remove the bulb and change it.
F Put the connector back in place.
F Reconnect the connector.
F Reit the protective cover. 4 - Direction indicators:

PY 21 W (amber).
F Turn the bulb holder a quarter turn
and remove it.
F Change the bulb.
Amber coloured bulbs (direction in-
dicators and side repeaters) must
be replaced with bulbs of identical
speciication and colour.
5 - Front fog lamps: H11-55 W.
Turn the wheels to full lock.
Access to the bulb is via the lap in
the front mud lap.
Contact a PEUGEOT dealer.
The headlamps are itted with poly-
carbonate glass with a protective
coating. Do not clean them with a dry
or abrasive cloth, nor with a deter-
gent or solvent product.
Ensure that the liquid used to ill the
wash-wipe and headlamp wash res-
ervoir is of good quality.
In certain climatic conditions (low
temperature, humidity), condensa-
tion on the inside surface of the
headlamp glass is normal; it disap-
pears a few minutes after the lights
are switched on.
407 saloon and 407 SW comfort

136 -
11-10-2004
137
-
11-10-2004
Direction indicator side repeaters:

WY 5 W (amber).
F Push the repeater forwards
or backwards and release the
assembly.
F Hold the connector and turn the
transparent cover a quarter turn.
F Change the bulb.
Amber coloured bulbs (direction in-
dicators and side repeaters), must
be replaced with bulbs of identical
speciication and colour.
407 saloon and 407 SW comfort

140 -141
-
REAR SEATS
To fold down the rear left seat or the rear
right seat, always start with the seat, nev-
er with the seat back (risk of damage):
F
move the front seat(s) forward if
necessary,
F place the head restraints in the
low position or remove them if
necessary,
Check that the seat belt strap is po-
sitioned correctly at the side of the
seat back,
Ensure that the side seat belt straps
are fastened in their clasp (the centre
seat belt must not be fastened), F lift the front of the seat cushion 1,
F tilt the seat cushion 1 against the
front seat(s),
F pull control 3 forwards to unlock
the seat back 2,
F fold down the seat back 2. Note:
the seat cushion 1 can be
removed with care to increase the
volume of the load space.
Squeeze the seat cushion ixings to
detach them from their fastenings.
When repositioning:F fold up the seat back 2 and lock
it (the red marker of control 3
should no longer be visible),
F fold up the seat 1,
F reit the head restraints if they
were removed.
Take care not to trap the seat belt
and to position the buckle of each
strap correctly in its respective clasp
before folding down the seat back.
This will enable you to reposition the
seat backs with their seat belts and
clasps ready to accommodate your
rear passengers. Locking/unlocking the access to
the boot via the rear seats
Your vehicle's boot can be isolated
from the passenger compartment.
The red indicator on the control
3
should no longer be visible. If it is,
push the seat fully.
Insert the ignition key in the lock 4.
407 saloon comfort
11-10-2004

140 -141
-407 saloon comfort
Notes:
After reconnecting the battery, you must
reinitialise the safety auto-reverse:
- place the control in the maximum
partial opening position (3rd notch
to the right),
- wait until the roof is in the maxi- mum partially open position,
- press the control for at least one second.
In the event of unwanted opening of
the roof on closing (for example, in
the presence of ice), and immedi-
ately after the roof stops:
- move the control to the "O" position
and press the control immediately,
- continue to press the control until the roof is fully closed.
In the partially open position, the roof
closes automatically above 60 mph
(100 km/h).
To partially open it again:
- move the control back to the "O" position,
- turn the control to the right.
The safety auto-reverse function is
not active during these operations.
SUNROOF
- To partially open the roof: Turn the
switch to the right (three possible
settings).
- To open the roof completely: Turn
the switch to the left (six possible
settings).
- To close it completely: Turn the
switch back to position "O".
- Safety auto-reverse: When the
sunroof is closing and meets an ob-
stacle, it stops then partially opens
again.
The sunroof shutter is manual. Always remove the key from
the ignition when leaving
the vehicle, even for a short
time.
In the event of contact during opera-
tion of the roof, you must reverse the
movement of the roof. To do this,
press the switch concerned.
When the driver operates the roof
switch, he must ensure that no one
is preventing correct closing of the
roof.
The driver must ensure that the pas-
sengers use the sunroof correctly.
Be aware of children when operating
the roof.
11-10-2004

142 -143
-
REAR COURTESY LIGHT
1 - Courtesy light
2 - Map reading lights
With the key in the ignition on or
starting position, operate the relevant
switch.
The rear courtesy light comes on
when the ignition key is removed, on
unlocking the vehicle or on opening
one of the doors.
It gradually goes off after the ignition
has been switched on or the vehicle
is locked.
F
Pressing switch 1 turns on the
rear courtesy light.
LUGGAGE COMPARTMENT
LAYOUT
Lashing rings
Use the 4 lashing rings on the lug-
gage compartment loor to secure
your luggage.
Luggage retaining net
Hooked onto the lashing rings, this
enables you to secure your luggage.
FITTING ROOF BARS
When itting transverse roof bars,
use the four quick-it ixings provided
for this purpose. Lift the concealing
laps and adjust the roof bar quick-it
ixings.
Maximum authorised weight
on the roof rack, for a loading
height not exceeding 40 cm
(with the exception of bicycle
carriers): 80 kg.
If the height exceeds 40 cm, adapt
the speed of the vehicle to the proile
of the road to avoid damaging the
roof bars and the ixings on the roof.
Be sure to refer to national legisation
in order to comply with the regula-
tions for transporting objects which
are longer than the vehicle.
407 saloon comfort
The courtesy light can be deacti-
vated by pressing switch 1 with the
door open. The map reading lights
are not affected by this and may be
switched on.
F To re-activate the lights, press the
switch, with the door open.
11-10-2004

142 -143
-
CHANGING A REAR BULB
1 - Direction indicators:
PY 21 W (amber).
2 - Brake lights/side lights: P 21/4 W.
3 - Reversing lights: P 21 W.
4 - Fog lamps/side lights:
P 21/4 W.
5 - Side lights: P 21/4 W. Third brake light:
Five W 5 W bulbs.
F

Remove the plastic cover carefully by
unclipping it on either side, perpen-
dicular to its direction of engagement.
F Press on the two tabs.
F Pull the red transparent cover out-
wards while maintaining the pres-
sure on the tabs.
F Change the faulty bulb.
F When reitting, ensure that the
tabs of the red transparent cover
are engaged correctly and that
the upper trim has been put back
in place correctly.
F
Disconnect the connector.
F Unclip the two seal tabs.
F Unclip the bulb holder moving
aside the 5 tabs.
F Unscrew the bulb and change it.
F Lock the bulb holder in place.
When reitting it, ensure that the
lamp is correctly positioned and
secured.
F Reposition the two seal tabs.
F Reconnect the connector.
Number plate lights: W 5 W.
F Remove the transparent cover us-
ing a screwdriver blade.
F Change the faulty bulb.
407 saloon comfort
11-10-2004

144145
-
REAR SEATS
To fold down the rear left seat or the rear
right seat, always start with the seat, nev-
er with the seat back (risk of damage):
F
move the front seat(s) forward if
necessary,
F place the head restraints in the
low position or remove them if
necessary,
Check that the seat belt strap is po-
sitioned correctly at the side of the
seat back,
Ensure that side seat belt straps are
fastened in their clasp (the centre
seat belt must not be fastened), F lift the front of the seat cushion 1,
F tilt the seat cushion 1 against the
front seat(s),
F pull control 3 forwards to unlock
the seat back 2,
F fold down the seat back 2. Note:
the seat cushion 1 can be
removed with care to increase the
volume of the load space.
Squeeze the seat cushion ixings to
detach them from their fastenings.
When repositioning:F fold up the seat back 2 and lock
it (the red marker of control 3
should no longer be visible),
F fold up the seat 1,
F reit the head restraints if they
were removed. Take care not to trap the seat belt
and to position the buckle of each
strap correctly in its respective clasp
before folding down the seat back.
This will enable you to reposition the
seat backs with their seat belts and
clasps ready to accommodate your
rear passengers.
407 SW comfort
11-10-2004