Peugeot 407 Dag 2005 Owner's Manual

150 -151
-
CHANGING A REAR BULB
1 - Direction indicators:
PY 21 W (amber).
2 - Reversing lights: P 21 W.
3 - Fog lamps/side lights:
P 21/4 W.
4 - Side lights: P 21/4 W.
5 - Brake lights/side lights:
P 21/4 W. Third brake light:
Five W 5 W bulbs.
F
Remove the plastic cover care-
fully by unclipping it at the centre
and on either side, perpendicular
to its direction of engagement.
F Press on the two tabs located at
the rear, near the rear screen.
F Pull the red transparent cover
outwards while maintaining the
pressure on the tabs.
F Change the faulty bulb.
F When reitting, ensure that the
tabs of the red transparent cover
are engaged correctly and that
the upper trim has been put back
in place correctly.
F
Disconnect the connector.
F Unscrew the light ixing nuts in-
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.
F Remove the seal.
F Unclip the bulb holder moving
aside the 5 tabs.
F Unscrew the bulb and change it.
F Lock the bulb holder in place.
F Reposition the seal.
F Screw on the light ixing nuts
inside the boot using the towing
eye, if necessary. When reitting,
ensure that the light is positioned
and ixed correctly.
F Reconnect the connector.
Number plate lights: W 5 W.
F Remove the transparent cover us-
ing a screwdriver blade.
F Change the faulty bulb.
407 saloon comfort
14-02-2005

152153
-
REAR SEATS
To fold down the rear left seat or the
rear right seat, always start with the
seat, never with the seat back (risk of
damage): F
move the front seat(s) forward if
necessary,
F place the head restraints in the
low position or remove them if
necessary,
Check that the seat belt strap is po-
sitioned correctly at the side of the
seat back,
Ensure that side seat belt straps are
fastened in their clasp (the centre
seat belt must not be fastened), F lift the front of the seat cushion 1,
F tilt the seat cushion 1 against the
front seat(s),
F pull control 3 forwards to unlock
the seat back 2,
F fold down the seat back 2. Note:
the seat cushion 1 can be
removed with care to increase the
volume of the load space.
Squeeze the seat cushion ixings to
detach them from their fastenings.
When repositioning:F fold up the seat back 2 and lock
it (the red marker of control 3
should no longer be visible),
F fold up the seat 1,
F reit the head restraints if they
were removed. Take care not to trap the seat belt
and to position the buckle of each
strap correctly in its respective clasp
before folding down the seat back.
This will enable you to reposition the
seat backs with their seat belts and
clasps ready to accommodate your
rear passengers.407 SW comfort
14-02-2005

154 -155
-
TRANSPORTING LONG
OBJECTS
Front passenger seat:
F
Tilt the seat back approximately
25° towards the rear (in relation
to the vertical position) using
the seat back angle adjustment
control (see corresponding para-
graph).
F Lift control A upwards to release
the seat back.
F Without releasing control A, press
on the top of the seat back and
move with it until it is folded. Rear seat (see corresponding
paragraph):
F
Tilt the seat cushion,
F Remove the head restraints,
F Tilt the seat back. Note:
when repositioning, ensure
that the front and rear seat backs are
secured correctly.
Precautions
- The long object must be placed on the end of the front seat back and
on the rear seat cushion.
- Do not place a load in excess of 30 kg on the front of the seat back.
- Do not load sharp objects, this could damage the rear of the
front seat back (storage pocket).
407 SW comfort
14-02-2005

154 -155
-
REAR WIPER CONTROL
Turn the ring to the irst notch for in-
termittent wiping.
The control must be reactivated if
the ignition has been switched off.
To do this, move the control to any
position then return it to the required
position.
Automatic rear wiper
If the windscreen wipers control is
activated and you engage reverse
gear, the rear wiper operates in inter-
mittent mode.
Note:
if a bicycle carrier is used, de-
activate this function by going to the
"personalisation-coniguration" menu
on the multifunction display or install
a special bicycle carrier approved by
PEUGEOT. Rear wash-wipe
Turn the ring beyond the irst notch,
the wash-wipe then the wiper oper-
ate for a set period of time.
Note:
the rear wiper and rear wash-
wipe functions are deactivated au-
tomatically when the rear screen is
opened. 407 SW comfort
14-02-2005

156 -157
-
TAILGATE AND REAR
SCREEN
The locking or unlocking of the tail-
gate and rear screen is simultaneous
with that of the doors.
Opening the tailgate and rear
screen
The tailgate and rear screen can-
not be opened at the same time.
With the rear screen closed, to open
the
tailgate , operate the handle A,
then lift the tailgate.
With the tailgate closed, to open the
rear screen , operate the handle B,
then lift the rear screen.
The lighting is controlled by opening
the tailgate or the rear screen. Partial opening of the rear screen
With the tailgate closed, to partially
open the
rear screen , press the
unlocking button C on the remote
control.
Notes: the tailgate and rear screen
lock automatically when driving at
6 mph (10 km/h) and unlock when
one of the doors is opened.
When the rear wiper is in a wiping
position, the rear screen cannot be
opened until the end of the cycle.
Close the rear screen using the wiper
arm or by pressing the centre of the
glass. "Rear screen open" warning
When the engine is running
, if the
rear screen is not fully closed, you
are warned by a message on the
multifunction display.
When the vehicle is moving (speed
greater than 6 mph (10 km/h)), if the
rear screen is not fully closed, you
are warned by an audible signal, a
message on the multifunction display
and lighting of the service warning
light.
Emergency control
This permits unlocking of the tailgate
in the event of a central locking op-
eration fault.
- Fold the rear seats to gain access to the lock from inside the boot,
- Insert a small screwdriver in the opening A in the lock to unlock the
tailgate.
407 SW comfort
14-02-2005

156 -157
-
To unfold
REAR READING LIGHTS
To fold
LOAD SPACE COVER
With the key in the ignition on or
starting position, press the corre-
sponding switch.
The rear reading lights come on
when the key is removed from the
ignition and when the vehicle is un-
locked.
They switch off gradually when the
ignition is switched on or when the
vehicle is locked.
F
Pressing switch 1 switches on the
rear reading light concerned for
ten minutes. 407 SW comfort
14-02-2005

158 -159
-
BOOT LAYOUT
3. Load space cover
To remove:

F Unclip the front ends and
remove the load space cover.
To install:
F Position the front ends of
the load space cover on its
support and press lightly to
put it in place.
1. 12 V accessories socket and
boot light
This is a lighter type 12 volt socket. It is installed on the rear
left trim and is supplied from the
ignition on position.
The boot light is controlled by
opening the tailgate or rear
screen.
4. Stowing rings
There are four stowing rings on
the boot loor to which the lug-
gage retaining net can be at-
tached.
2. Storage boxes
There are two side storage box-
es which can contain:
- on the left: a can of oil, a irst aid kit, a puncture repair
aerosol,
- on the right (except when a JBL Hi-Fi system is itted):
a box of bulbs, a warning
triangle (support provided for
this purpose), the luggage
retaining net.
407 SW comfort
14-02-2005

158 -159
-
High load retaining net
The high load retaining net can be
used behind the front seats (row 1) or
behind the rear bench seat (row 2).
Note:
if it is used behind the front
seats, the rear seat backs and cush-
ions must be folded (see section on
rear seats).
To install it:
F fold the rear seat backs,
F position the high load retaining net
roller above the two rails 5 located
behind the rear seats (2/3 bench
seat). The two notches 6 must be
placed above the two rails,
F
slide the two rails 5 in the notches 6,
F push the roller (in the direction of
the length) from right to left to se-
cure it,
F put the rear seat backs back in
place. To use it in
row 1:
F fold the rear seat backs,
F open the covers 7 of the corre-
sponding upper ixings,
F unroll the high load retaining net
and position one end of the metal
bar in the corresponding ixing
cover. Ensure that the hook is
seated correctly in the rail located
inside the cover 7,
F pull the metal bar on the high load
retaining net to position the other
hook in the second ixing cover. 407 SW comfort
14-02-2005

160 -161
-
FITTING ROOF BARS
When itting transverse roof bars,
ensure that they are positioned cor-
rectly.
The correct positions are shown by
marks on each of the longitudinal
bars.
Use accessories approved by
PEUGEOT and follow the manufac-
turer's itting instructions.
Maximum authorised weight
on the roof bars, for a loading
height not exceeding 40 cm (ex-
cept bicycle carriers): 100 kg.
If the height exceeds 40 cm, adapt
the speed of the vehicle to the condi-
tion of the road, to avoid damaging
the roof bars.
Please refer to national legislation
to comply with the regulations re-
garding the transportation of objects
which are longer than the vehicle.
To use it in
row 2:
F open the covers 8 of the corre-
sponding upper ixings,
F from the rear bench seat, unroll
the high load retaining net push-
ing it to detach it from the retain-
ing hooks,
F position one of the ends of the
metal bar of the net in the corre-
sponding ixing cover. Ensure that
the hook is seated correctly in the
rail located inside the cover 8,
F position the other hook in the sec-
ond ixing cover and pull the metal
bar towards you.
407 SW comfort
14-02-2005

160 -161
-
Safety auto-reverse
If the shutter encounters an obstacle
during closing, it stops and partially
opens again.
You must reinitialise the safety auto-
reverse within a maximum of ive
seconds after the concealing shutter
has stopped:
- press part
A of the control until the
shutter is completely closed (clos-
ing in stages of a few centimetres).
Notes
Following reconnection of the battery,
in the event of a shutter malfunction
while it is moving or immediately af-
ter it has stopped, you must reinitial-
ise the safety auto-reverse:
- place the control in the fully open position (position "0"),
- wait until the shutter is in the fully open position,
- press section A of the control for at
least three seconds.
In the event of unwanted opening of
the shutter on closing, and immedi-
ately after the shutter has stopped:
- move the control to the fully closed position (9th setting to the left) then
press part A of the control straight
away,
- continue to press the control until the shutter is fully closed.
The safety auto-reverse function
is not active during these opera-
tions.
PANORAMIC ROOF
Your vehicle is itted with a tinted
glass panoramic roof which in-
creases the light and visibility in the
passenger compartment. Its electric
concealing shutter improves tem-
perature conditions.
The concealing shutter is control-
led electrically by a dial with nine
opening positions.
To close: turn the dial to the left
(nine possible settings).
To open: return the dial to the initial
position "0". In the event of contact during
operation of the shutter, you
must reverse its movement.
To do this, press the control
concerned.
When the driver operates the shutter
control, he must ensure that no one
is preventing the shutter from closing
correctly.
The driver must ensure that the pas-
sengers use the concealing shutter
correctly.
Pay attention to children during op-
eration of the shutter. 407 SW comfort
14-02-2005