battery Peugeot 508 2011 Owner's Manual
Page 5 of 340
.
.
Contents
Child seats 146
ISOFIX child seats 152
Child safety
Direction indicators 157
Emergency or assistance call 158
Horn 158
Ty r e u n d e r- i nfl ation detection 159
ESP system 160
Seat belts 163
Airbags 166
Safety
Temporary puncture repair kit 170
Changing a wheel 176
Changing a bulb 183
Changing a fuse 192
12 V battery 196
Energy economy mode 199
Changing a wiper blade 200
Towing the vehicle 201
Towing a trailer 202
Fitting roof bars 204
Accessories 205
Practical information
Opening the bonnet 208
Running out of fuel (Diesel) 209
Petrol engines 210
Diesel engines 211
Checking levels 213
Checks 216
Checks
Petrol engines 218
Petrol weights 219
Diesel engines 221
Diesel weights 224
Dimensions 227
Identifi cation markings 228
Technical data
Emergency or assistance 229
JBL equipment 231
Peugeot Connect Navigation (RT6) 233
Audio system 287
Audio equipment and telematics
Alphabetical index
Visual search
Page 31 of 340
1
29
Instruments and controls
Warning or indicator lamp
in the instrument panel
State
Cause
Action/Observations
Engine oil
pressure
fixed. There is a fault with the engine
lubrication system. You must stop as soon it is safe to do so.
Park, switch off the ignition and contact a PEUGEOT
dealer or a qualified workshop.
Battery charge
fixed. The battery charging circuit has a
fault (dir ty or loose terminals, slack or
cut alternator belt, ...). The warning lamp should go off when the engine is
started.
If it does not go off, contact a PEUGEOT dealer or a
qualified workshop.
Door(s) open
fixed, associated with
a message identifying
the door, if the speed is
below 6 mph (10 km/h). A door or the boot is still open. Close the door or boot.
fixed, associated with a
message identifying the
door, and accompanied
by an audible signal if
the speed is above
6 mph (10 km/h).
Page 36 of 340
34
i
i
Instruments and controls
Service overdue
For 5 seconds after the ignition is switched on,
the spanner flashes
to indicate that the service
must be carried out as soon as possible.
Example:
the ser vice is overdue by 186 miles
(300 km).
For 5 seconds after the ignition is switched on,
the screen indicates:
The distance remaining may be
weighted by the time factor, depending
on the driving conditions.
Therefore, the spanner may also come
on if you have exceeded the two year
ser vice inter val.
Following this operation, if you wish to
disconnect the battery, lock the vehicle
and wait at least five minutes for the
zero reset to be taken into account. 5 seconds after the ignition is switched on,
the distance recorder resumes its normal
operation. The spanner remains on
.
Service indicator zero reset
After each ser vice, the ser vice indicator must
be reset to zero.
The procedure for resetting to zero is as
follows:
)
switch off the ignition,
)
press and hold the trip distance recorder
zero reset button,
)
switch on the ignition; the distance recorder
display begins a countdown,
)
when the display indicates "=0"
, release
the button; the spanner disappears.
Retrieving the service
information
You can access the ser vice information at any
time.
)
Press the trip distance recorder zero reset
button.
The ser vice information is displayed for a
few seconds, then disappears.
Page 44 of 340
42
i
!i!
Access
As a safety measure (children on
board), never leave the vehicle without
taking your key, even for a short period.
Guard against theft when the electronic
key is in the defined zone with the
vehicle unlocked.
Locking is confirmed by fixed
lighting of the direction indicators for
approximately two seconds.
According to version, the door mirrors
fold at the same time.
If one of the doors or the boot is still
open or if an electronic key has been
left inside the vehicle, the central
locking does not take place.
When the vehicle is locked, if it is
unlocked inadvertently, it will relock
automatically after about thir ty seconds
unless a door is opened.
It is not possible to lock the vehicle if an
electronic key is left inside the vehicle.
After a long period of parking, the
automatic detection functions of the
electronic key are inhibited so as to not
discharge the vehicle's battery. You
should then use the remote control
function of the electronic key to unlock
the vehicle. The folding and unfolding of the door
mirrors by the remote control can be
deactivated by a PEUGEOT dealer.
Deadlocking
Deadlocking renders the exterior and
interior door controls inoperative.
It also deactivates the manual central
control button.
Therefore, never leave anyone inside
the vehicle when it is deadlocked.
Using the key
)
Turn the key to the rear in the driver's door
lock to lock the vehicle completely.
)
Turn the key to the rear again within five
seconds to deadlock the vehicle.
Page 47 of 340
2
45
Access
Emergency procedure
Emergency unlocking/
locking
using the electronic key
The integral key is used to lock and unlock the
vehicle when the electronic key cannot operate:
- cell battery flat, vehicle battery discharged
or disconnected, ...
- vehicle located in an area with strong
electromagnetic emissions.
)
Pull on button 1
, to extract the integral key 2
.
)
Unlock or lock the vehicle using the key.
Manual locking
Driver's door
Inser t the key in the lock to lock or unlock the
door.
Passenger doors
)
On the rear doors, check that the child lock
is not on.
)
Remove the black cap located on the edge
of the door, using the key.
)
Inser t the key into the aper ture without
forcing, then without turning, move the latch
sideways towards the inside of the door.
)
Remove the key and refit the cap.
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
)
First of all, use the key in the lock to unlock
or lock your vehicle.
)
Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT
dealer or a qualified workshop as soon as
possible.
Reinitialisation with the remote
control
)
Switch on the ignition.
)
Immediately press one of the remote
control buttons for a few seconds.
)
Switch off the ignition.
The remote control is fully operational again.
Page 48 of 340
46
Access
Changing the battery of the key
Battery ref.: CR2032/3 volts.
This replacement battery is available from a
PEUGEOT dealer or a qualified workshop.
A message appears in the instrument panel
screen when replacement of the battery is
needed.
)
Unclip the cover using a small screwdriver
at the cutout.
)
Lift off the cover.
)
Remove the flat battery from its location.
)
Fit the new battery into its location
obser ving the original direction of fitment.
)
Clip the cover onto the casing.
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
Reinitialisation with the
electronic key
)
Switch of the ignition.
)
Immediately press one of the remote
control buttons for a few seconds.
)
Switch on the ignition
The electronic key is fully operational again.
Changing the battery of the
electronic key
Battery ref.: CR2032/3 volts.
This replacement battery is available from a
PEUGEOT dealer or a qualified workshop.
A message is displayed in the instrument panel
screen when replacement of the battery is
needed.
)
Unclip the cover using a pointed object at
the key ring.
)
Slide the flat battery out of its location.
)
Slide the new battery into its location
obser ving the original direction of fitment.
)
Clip the cover in place star ting at the front.
)
Reinitialise the electronic key.
Page 50 of 340
48
!
Access
System which protects and provides a deterrent
against theft and break-ins. It provides the
following types of monitoring:
Alarm
- Exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot or the bonnet...
- Interior volumetric
The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compar tment or
moves inside the vehicle.
- Tilt
The system checks for any change in the
attitude of the vehicle.
The alarm is triggered if the vehicle is lifted,
moved or knocked.
Self-protection function
The system checks for the putting out of
ser vice of its components.
The alarm is triggered if the battery, the
central control unit or the wires of the
siren are put out of ser vice or damaged.
For all work on the alarm system,
contact a PEUGEOT dealer or a
qualified workshop.
Locking the vehicle with full
alarm system
Activation
)
Switch off the ignition and get out of the vehicle.
)
Press the locking button on the
remote control or lock the vehicle
using the Keyless Entry and
Star ting system. The monitoring system is active: the indicator
lamp on the button flashes once per second.
After the locking button on the remote control
is pressed or the vehicle locked using the
Keyless Entry and Star ting system, the exterior
perimeter monitoring is activated after a delay
of 5 seconds and the interior volumetric and
anti-tilt monitoring after a delay of 45 seconds.
If an opening (door, boot...) is not closed
fully, the vehicle is not locked but the exterior
perimeter monitoring will be activated after a
delay of 45 seconds at the same time as the
interior volumetric and anti-tilt monitoring.
)
Press the unlocking button on
the remote control or unlock the
vehicle using the Keyless Entry
and Star ting system.
Deactivation of the volumetric
monitoring
The volumetric protection system is
deactivated: the indicator lamp in the
button goes off.
Page 53 of 340
2
51
!
Access
Reinitialisation of the
electric windows
Always remove the key from the ignition
when leaving the vehicle, even for a
shor t time.
In the event of contact during operation
of the windows, you must reverse the
movement of the window. To do this,
press the switch concerned.
When operating the passenger electric
window switches, the driver must
ensure that no one is preventing correct
closing of the windows.
The driver must ensure that the
passengers use the electric windows
correctly.
Be aware of children when operating
the windows.
Following reconnection of the battery, the
safety anti-pinch function must be reinitialised.
The safety anti-pinch function is not active
during these operations:
- lower the window completely, then raise
it, it will rise in steps of a few centimetres
each time the switch is pressed. Repeat
the operation until the window closes
completely,
- continue to press the switch for at least one
second after reaching this position, window
closed.
Page 57 of 340
2
55
Access
Emergency release
(Saloon and SW)
System for mechanical unlocking of the boot in
the event of a battery or central locking fault.
Unlocking
)
Fold back the rear seats to gain access to
the lock from inside the boot.
)
Inser t a small screwdriver into hole A
of the
lock to unlock the tailgate.
"Boot open" warning
With the engine running or when the vehicle is
moving, if the tailgate is not properly closed,
a message accompanied by an audible signal
(from 6 mph (10 km/h)) is displayed in the
instrument panel screen.
Page 59 of 340
2
57
!
Access
In the event of contact during operation
of the blind, you must reverse its
movement. To do this, turn the dial.
When the driver operates the dial, they
must ensure that nothing prevents the
blind from closing correctly.
The driver must ensure that the
passengers use the blind correctly.
Be aware of children during operation
of the blind.
Reinitialising the system
Following reconnection of the battery, or in the
event of a malfunction in its operation, it may be
necessary to reinitialise the system:
)
turn the dial to the fully open position,
)
wait until the blind is fully open,
)
then immediately press the dial for at least
3 seconds,
If the blind opens on its own when closing, as
soon as possible after the blind stops:
- put the dial in the fully closed position,
- press the dial,
- maintain pressure on the dial until the blind
closes.
The anti-pinch function is inoperative
during these operations.