ignition PEUGEOT 607 2003 Owner's Manual

10-02-2003
Ending a call During, or at the end of, a communi- cation, press the end of the steeringwheel control to display the "Hang
up the call" function, then validate
the "YES" button by pressing the
control again. Second call* This function enables you to:
- receive a second call: you are informed by a bleep and a display,
- make a second call (this function is carried out directly using the tele- phone keypad).
When a second call is receivedduring a call, the message "take/do
not take the call" appears. If you
do not take the second call, youcontinue the first call, but if you takeit, the first call is put on hold.
* If the option and service are available. Switching between calls During a call, press the end of the steering wheel control to display thecontrol button:
- when it is selectedand then confirmedusing the steeringwheel control, thebutton enables youto switch from onecorrespondent to
the other,
- this button enables you to hang up thecurrent call.
SMS messages The receipt of SMS messages is indicated by a symbol (envelope) on
the multi-function display. SMS messages must be written, sent or read using the mobile tele-phone. Directories The
"Telephone directories" func-
tion enables you to consult their content and make a call, but in nocase does it enable you to make anychanges. The mobile telephone's directories are loaded in the system's memory(maximum 254 numbers).
Two cases can be envisaged:
- the telephone used is the same as that used last time the system was used: the initial data is availableimmediately; the data added in themeantime will be available after a
brief loading time. You will not haveaccess to this update via thehands-free kit until the ignition has
been switched off and then onagain;
- the telephone used is different from that used last time the systemwas used: the data will be avai-lable after a loading time whichdepends on how many numbersare to be transferred (between 15 seconds and 3 minutes).
YOUR 607 IN DETAIL
74

10-02-2003
The ''Navigation/Guidance'' menu offers following options:
- inputting of the address of a new destination,
- selection of a service (hotel, station, airport...) available in a town,
- selection of an address stored in one of the two directo- ries,
- access to the "Navigation Options" menu.
Main menu Switch on the ignition. Press the
'Menu'button to access the 'Main menu'.
Select a function by turning the dial, then confirm (press the dial). Navigation / guidance Following selection of the 'Navigation / guidance'menu,
a screen warns you about the use of the navigation sys- tem. Please observe the instructions. Press the dial to access the next screen.
YOUR 607 IN DETAIL
80

10-02-2003
Main menu
Ð Switch on the ignition,
Ð Place the mapping CD-ROM in thedrive (if absent),
Ð Press the 'Menu'button to access
the Main menu ,
Ð Select one of the following applica- tions by turning the dial, then con- firm:
¥ General information (see section on ''Multi-function display - &
Colour screen'' ),
¥ Navigation / Guidance ,
¥ Map. Navigation / guidance The
''Navigation/Guidance'' con-
text menu offers the following possi- bilties: Ð selecting a destination,Ð guidance using a map,Ð changing the route,Ð details of the route,Ð geographical information,Ð guidance options,Ð stopping/resuming guidance.
YOUR 607 IN DETAIL 87

10-02-2003
YOUR 607 IN DETAIL101
Memorising using the buttons
To memorise:
 Place the ignition key in the 'run- ning' position (2nd notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) withinfour seconds.
An audible signal confirms that aposition has been memorised. Memorising a new position cancels the previous one. Recalling a memorised position Engine off  Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting isindicated by a bleep.
Note: after recalling a memorised
position five times in succession, thefunction will be cancelled until theengine is started. Engine running
 Keep button 1 or 2pressed down
until the bleep indicates the end of setting of the corresponding mem-orised position.
Memorising seat and mirror positions Four driving positions can be memo- rised:
Ð two, using two remote control
keys (two users) ,
Ð two, using buttons M/1 and M/2.
Driving positions memorised bythe remote control key When locking the doors, the remote control key memorises the positionof the driver's seat and the exteriormirrors. When unlocking the doors, the dri- ver's seat and the exterior mirrorsresume the position memorised bythe remote control key if this haschanged in the meantime. Each remote control key can memorise a specific setting. Front and rear heated seats controls
 Press the switch. The tempera-
ture is regulated automatically.
 Press it again to stop operation.
Note: the command to activate heat-
ing of the seat(s) remains in thememory for two minutes after the
ignition is switched off.

10-02-2003
YOUR 607 IN DETAIL
100
Electric front seats
A - Forwards-backwards adjustment
Push the control forwards or backwards to slide the seat.
B - Seat cushion angle adjustment Tilt the front of the control upwards or downwards toobtain the required angle.
C - Seat height adjustment Tilt the rear part of the control upwards or downwardsto obtain the required height.
D - Seat back angle adjustment Tilt the control to the front or the rear to obtain the cor-rect angle.
E - Lumbar adjustment (mechanical adjustment) Raise or lower the lever to obtain the correct position.
F - Head restraint height adjustment Tilt the control upwards or push it downwards to obtainthe correct height.
The setting is correct when the upper edge ofthe head restraint is level with the top of thehead.
The head restraint angle is also adjustable manually.
To remove the head restraint, tilt the seat back to 45¡ and place the head restraint in the high position, thenpull with both hands.
Note: the electrical functions of the driver's seat are inoper-
ative three minutes after the ignition has been switched off.

10-02-2003
YOUR 607 IN DETAIL101
Memorising using the buttons
To memorise:
 Place the ignition key in the 'run- ning' position (2nd notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) withinfour seconds.
An audible signal confirms that aposition has been memorised. Memorising a new position cancels the previous one. Recalling a memorised position Engine off  Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting isindicated by a bleep.
Note: after recalling a memorised
position five times in succession, thefunction will be cancelled until theengine is started. Engine running
 Keep button 1 or 2pressed down
until the bleep indicates the end of setting of the corresponding mem-orised position.
Memorising seat and mirror positions Four driving positions can be memo- rised:
Ð two, using two remote control
keys (two users) ,
Ð two, using buttons M/1 and M/2.
Driving positions memorised bythe remote control key When locking the doors, the remote control key memorises the positionof the driver's seat and the exteriormirrors. When unlocking the doors, the dri- ver's seat and the exterior mirrorsresume the position memorised bythe remote control key if this haschanged in the meantime. Each remote control key can memorise a specific setting. Front and rear heated seats controls
 Press the switch. The tempera-
ture is regulated automatically.
 Press it again to stop operation.
Note: the command to activate heat-
ing of the seat(s) remains in thememory for two minutes after the
ignition is switched off.

10-02-2003
YOUR 607 IN DETAIL109
SEAT BELTS Front seat belt height adjustment :  To lower the attachment point, squeeze control 1and slide it
downwards.
 To raise the attachment point,squeeze control 1 and slide it
upwards.
To lock the seat belts  Pull the strap, then insert the endinto the buckle. Front seat belts with pre-tensioner and force limiter Safety in the event of a frontal impact has been improved by the introduc-tion of seat belts with pre-tensionerand force limiter connected to thefront air bags. Depending on theseriousness of the impact, the pre-tensioning system instantly tightensthe seat belts firmly against the bod-ies of the occupants. The pre-tensioning seat belts are armed when the ignition is on. The force limiter reduces the pres- sure of the seat belt on the body ofthe occupant in the event of an acci-dent. Rear seat belts with force limiter The rear seats are all fitted with a three-point inertia reel seat belt. Third rear central seat belt
Ð pull the belt located between the
two head restraints at the left rear,
Ð insert the fixed buckle in the black clasp located on the left,
Ð insert the sliding buckle in the red and black (movable) clasp.
To release it, press the black button of the locking clasp. To be effective, a seatbelt must be tightened asclose to the body as pos-sible.
Depending on the nature and seri-ousness of the impact, the pre-tensioners may be triggeredbefore and independently of theair bags. In all cases, the air bag warning light comes on. After an impact, have the system
checked by a PEUGEOT dealer. The system has been designed to be fully operational for ten years.
For improved safety, have it checked by a PEUGEOT dealerwithin ten years of purchase of thevehicle.

10-02-2003
YOUR 607 IN DETAIL111
Electronic engine immobiliser This locks the engine control system a few moments after the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the codeis recognised and starting is possi-ble. If the system does not function
correctly, the central locking button
indicator light, situated on the centreconsole, flashes rapidly when theignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon as possible. Flat battery (CR 2025/3 volt battery) This is indicated by illumination of a warning light on the instrument panel
display, accompanied by an audiblesignal and a message on the multi-
function display.
Contact a PEUGEOT dealer to
replace the battery.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition. Locating your vehicle
To locate your vehicle, if you have locked it, in a car park:
 press button A. The courtesy
lights come on and the directionindicators flash for a few seconds.
CONFIDENTIAL CARD The confidential card contains the identification code necessary for anywork carried out by a PEUGEOT
dealer on the system. This code ishidden by a film, which should be
removed only if necessary. Keep your card in a safe place, never inside the vehicle. Programming the remotecontrol Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and removethe remote control key from the
ignition lock. The remote control isnow working again.

10-02-2003
Make a careful note of the number on each key. The key number is coded on the label attached to the key. If the keys are lost, your PEUGEOT dealer can rapidly supply you with new keys.The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock your vehicle, without you being aware of it.
The remote control does not operate when the key is in the ignition, even when the ignition is switched off, except forreprogramming.
However, do not operate the deadlocking function if there is anyone inside the vehicle.Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult
in an emergency. As a safety precaution (with children on board), remove the ignition key when you leave the vehicle, even for a short time.Do not repeatedly press the button of your remote control out of range of your vehicle.
You run the risk of stopping it from working and the remote control would have to be reprogrammed. When purchasing a second-hand vehicle: - ensure that you are given the confidential card;
- have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones which can start the vehicle.
Do not make any modifications to the electronic engine immobiliser system.
YOUR 607 IN DETAIL
112

10-02-2003
YOUR 607 IN DETAIL111
Electronic engine immobiliser This locks the engine control system a few moments after the ignition has
been switched off and therefore pre-vents starting of the vehicle by any-
one who does not have the key. The ignition key has an electronic chip which has a special code. Whenthe ignition is switched on, the codeis recognised and starting is possi-ble. If the system does not function
correctly, the central locking button
indicator light, situated on the centreconsole, flashes rapidly when theignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon as possible. Flat battery (CR 2025/3 volt battery) This is indicated by illumination of a warning light on the instrument panel
display, accompanied by an audiblesignal and a message on the multi-
function display.
Contact a PEUGEOT dealer to
replace the battery.
Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition. Locating your vehicle
To locate your vehicle, if you have locked it, in a car park:
 press button A. The courtesy
lights come on and the directionindicators flash for a few seconds.
CONFIDENTIAL CARD The confidential card contains the identification code necessary for anywork carried out by a PEUGEOT
dealer on the system. This code ishidden by a film, which should be
removed only if necessary. Keep your card in a safe place, never inside the vehicle. Programming the remotecontrol Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and removethe remote control key from the
ignition lock. The remote control isnow working again.