bulb PEUGEOT 607 2007.5 Owners Manual

Page 24 of 187

1
27
Anti-lock braking system
(ABS) warning light
This is linked to the warn-
ing light on the instrument
panel.
Display of this warning light is ac-
companied by an audible signal and a
message on the multifunction display.
If the warning light remains on, or
comes on at over 8 mph (12 km/h), this
indicates a malfunction of the ABS.
However, the vehicle retains conven-
tional servo-assisted braking.
Contact a PEUGEOT dealer.
Automatic headlamp
adjustment warning light
Display of this warning light
is accompanied by an audi-
ble signal and a message on
the multifunction display.
It comes on if there is a malfunction of
the system on vehicles i tted with xe-
non bulbs.
Contact a PEUGEOT dealer. Electronically controlled
suspension warning light
Display of this warning light
is accompanied by an audi-
ble signal and a message on
the multifunction display.
It comes on when there is a malfunc-
tion of the electronically controlled
suspension.
Select the automatic mode and con-
tact a PEUGEOT dealer.
Particulate emission i lter
saturation warning light
(Diesel)
Display of this warning light
is accompanied by an audi-
ble signal and a message on
the multifunction display.
When it comes on with the engine
running, this indicates the start of
saturation of the particulate emission
i lter (exceptionally long periods of
town type driving conditions: reduced
speed, long tailbacks...).
To regenerate the i lter, you are ad-
vised to drive as soon as possible
and when trafi c conditions permit at a
speed of 35 mph (60 km/h) or more for
at least i ve minutes (until the warning
light goes out).
If the light remains on, contact a PEUGEOT
dealer.
When it comes on when the vehicle is
moving, it indicates a lack of diesel ad-
ditive in the reservoir for burning of the
particles.
Contact a PEUGEOT dealer.

Note: after prolonged operation of
the vehicle at a very low speed or at
idle, you may sometimes notice steam
coming from the exhaust during ac-
celeration. This has no effect on the
performance of the vehicle or on the
environment.

Page 123 of 187

1010PRACTICAL INFORMATION
106
CHANGING A BULB
2 - Main beam headlamps: H1-55
W.

 Turn the protective cover of the
faulty bulb a quarter of a turn and
remove it.

 Disconnect the connector.

 Press the end of the securing clip
to free it. Change the bulb.

 When i tting the new bulb, ensure
that the direction notches are po-
sitioned correctly and the securing
clip is i xed properly.

 Reconnect the connector.

 Rei t the protective cover.
3 - Side lights: W 5 W.

 Pull the socket rearwards.

 Remove the bulb and change it.
Front foglamps: H1-55 W.
The headlamps are i tted with
polycarbonate glass with a
protective coating. Do not
clean them with a dry or abra-
sive cloth, nor with a detergent or solvent
product.
Use a soft, damp cloth with soapy water.
In the engine compartment, remove
the style cover secured by one or two
butterl y screws, a plastic retainer clip
and two quarter turn screws.
On the left-hand side, remove the par-
tition by lifting it to gain access to the
lights.
When you have i nished, do not forget
to put everything back correctly.

WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be replaced
by a PEUGEOT dealer.
Note: in certain climatic con-
ditions (low temperature, hu-
midity), condensation on the
inside surface of the head-
lamp glass is normal ; it disappears
a few minutes after the lights are
switched on.
Handle the bulbs with a dry cloth.
Front lights
1 - Dipped beam headlamps:
H7-55 W or Xenon bulb. 4 - Direction indicators:
PY 21 W
(amber).

 Turn the bulb holder a quarter turn
and remove it.

 Remove the bulb and change it.

 Rei t the style cover.

High pressure washing
When using this type of washing on
stubborn dirt, do not persist on the
headlamps, the lights and their sur-
rounds to avoid damaging their var-
nish and their seal.

Page 124 of 187

1010PRACTICAL INFORMATION
107
Integrated direction indicator
repeaters Amber coloured bulbs, such
as the direction indicators and
side repeaters, must be re-
placed with bulbs of identical
specii cation and colour. Rear lights

 Remove the two butterl y nuts se-
curing the light.

 Remove the eyelet.

 Take out the lamp.

 Unclip the bulb holder.

 Change the faulty bulb.

 Clip the bulb holder.
When rei tting it, ensure that the lamp
is correctly positioned and secured.

1.
Direction indicators: Hp16.


2.
Brake lights/side lights: Hp16.


 Detach the luggage net.

 Lift the boot carpet with the lifting
hook. Secure this hook behind the
boot seal.

 Unclip the lower part of the sill
trim, then dislodge it by pulling up-
wards.

 Remove the plastic retainer clip
securing the side trim to the l oor.

 Unclip the side trim.

 Push the repeater forwards and re-
lease it.

 Remove the repeater and change it.
This can be obtained from a PEUGEOT
dealer. Rear wing lights

Page 125 of 187

1010PRACTICAL INFORMATION
107
Integrated direction indicator
repeaters Amber coloured bulbs, such
as the direction indicators and
side repeaters, must be re-
placed with bulbs of identical
specii cation and colour. Rear lights

 Remove the two butterl y nuts se-
curing the light.

 Remove the eyelet.

 Take out the lamp.

 Unclip the bulb holder.

 Change the faulty bulb.

 Clip the bulb holder.
When rei tting it, ensure that the lamp
is correctly positioned and secured.

1.
Direction indicators: Hp16.


2.
Brake lights/side lights: Hp16.


 Detach the luggage net.

 Lift the boot carpet with the lifting
hook. Secure this hook behind the
boot seal.

 Unclip the lower part of the sill
trim, then dislodge it by pulling up-
wards.

 Remove the plastic retainer clip
securing the side trim to the l oor.

 Unclip the side trim.

 Push the repeater forwards and re-
lease it.

 Remove the repeater and change it.
This can be obtained from a PEUGEOT
dealer. Rear wing lights

Page 126 of 187

1010PRACTICAL INFORMATION
108

 Remove the three plastic retainer
clips securing the cover trim (those
nearest to the lamp).

 Move aside the trim.

 Disconnect the lamp harness.

 Extract the lamp from its housing.

 Remove the l at seal.

 Unclip the bulb holder.

 Change the faulty bulb.

 Clip the bulb holder.

 Put the l at seal back in place.
When rei tting it, ensure that the lamp
is correctly positioned and secured.
Number plate lights: W 5 W.

 Remove the transparent cover us-
ing a screwdriver blade.

 Change the faulty bulb.
Boot lid lights

1.
Reversing lights: Hp16.

2.
Side lights: Hp16.

3.
Fog lamps: Hp16.
If you encounter any difi culties,
contact a PEUGEOT dealer.