PEUGEOT 607 2007 Owner's Guide

1
32
INSTRUMENT PANEL DISPLAY SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer's servicing schedule.
The point at which the service is due is
calculated from the last indicator zero re-
set. It is determined by two parameters:
- the distance travelled,
- the time elapsed since the last service.

Note: the distance remaining before
the next service is due may be weight-
ed by the time factor.
The service information appears on
the display, located in the speedo-me-
ter dial, at the same time as the en-
gine oil level on the instrument panel
display. Operation
As soon as the ignition is switched on
and for 7 seconds, the spanner sym-
bolising the servicing operations is lit.
The trip recorder display shows the
distance remaining (in round i gures)
before the next service.

Example: 4,800 miles/km remain be-
fore the next service is due. When the
ignition comes on and for 7 seconds
the display indicates:
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the display
shows the total and trip distances.
After switching on the ignition, two
functions are shown in succession:
- service indicator,
- total distance recorder (total and
trip distances).

Note: the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening the
driver’s door, as well as on locking and
unlocking the vehicle.

1
33

The distance remaining before the
next service is less than 500 miles
(1,000 km).
Each time the ignition is switched on
and for 7 seconds, the spanner and
the distance l ash.

Example: 900 miles/km remain before
the next service is due.
When switching on the ignition and for
7 seconds, the display shows:
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit.
This indicates that a service should be
carried out shortly. The display shows
the total and trip distances. 7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit. The display shows the total
and trip distances.

Note: the spanner may also be lit if the
two-year interval has been exceeded. Service indicator zero re-set

The service is overdue. .
Each time the ignition is switched on
and for 7 seconds, the spanner and
the excess distance l ash.

Example: the service is overdue by
300 miles/km. The service should be
carried out very shortly.
When the ignition is switched on and
for 7 seconds, the display shows:
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
After this operation, if you
wish to disconnect the battery,
lock the vehicle and wait for at
least i ve minutes, otherwise
the zero re-set will not be registered.

1
33

The distance remaining before the
next service is less than 500 miles
(1,000 km).
Each time the ignition is switched on
and for 7 seconds, the spanner and
the distance l ash.

Example: 900 miles/km remain before
the next service is due.
When switching on the ignition and for
7 seconds, the display shows:
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit.
This indicates that a service should be
carried out shortly. The display shows
the total and trip distances. 7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the spanner re-
mains lit. The display shows the total
and trip distances.

Note: the spanner may also be lit if the
two-year interval has been exceeded. Service indicator zero re-set

The service is overdue. .
Each time the ignition is switched on
and for 7 seconds, the spanner and
the excess distance l ash.

Example: the service is overdue by
300 miles/km. The service should be
carried out very shortly.
When the ignition is switched on and
for 7 seconds, the display shows:
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
After this operation, if you
wish to disconnect the battery,
lock the vehicle and wait for at
least i ve minutes, otherwise
the zero re-set will not be registered.

1
34
Trip recorder zero reset button Lighting rheostat button
With the ignition on, press the button
until the zeros appear. With the headlamps on, press button
B
to increase the brightness of the light-
ing of the instruments and controls or
button A to reduce it.
As soon as the lighting reaches the re-
quired level of brightness, release the
button.

1
35
TRIP COMPUTER
Each press on the button, located at
the end of the wipers stalk , displays
different trip computer data in succes-
sion, depending on the multifunction
display: - the
"vehicle" tab with:

1
36
Range (km or miles)
This shows the distance that can
still be covered with the fuel remaining
in the tank in accordance with the
average consumption over the last few
miles (kilometres).
This i gure may increase if there is a
change in the style of driving or the
road surface, producing a signii cant
drop in current consumption.
When the range is less than 30 miles
(50 km), four dashes are displayed.
After i lling with fuel, the range is
displayed when it exceeds 62 miles
(100 km).
If dashes are displayed for long periods
instead of digits, contact a PEUGEOT
dealer.
Current consumption
(l/100 or km/l or mpg)
This is the average quantity of fuel con-
sumed during the last few seconds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average consumption
(l/100 or km/l or mpg)
This is the average fuel consumption
since the computer was last set to
zero. Distance travelled
(km or miles)
This indicates the distance travelled
since the computer was last set to
zero.
Distance remaining to be
travelled (km or miles)
This is the distance remaining to be
travelled to the i nal destination. It is
either calculated by the navigation
system if guidance is activated or en-
tered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed (km/h or mph)
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The routes
"1" and "2" are indepen-
dent but have identical application.
Route "1" for example allows you to
make daily calculations and route "2"
monthly calculations.
The routes
Zero reset
When the required route is displayed,
press the end of the wipers stalk for
more than two seconds.

1
37
Warnings log
This summarises the active warning
messages, displaying them on the
multifunction display in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Inputting the distance remaining to
be travelled
When guidance is not activated, this
enables you to enter an approximate
distance to the i nal destination.
Access via the general menu
C screen
DT screen
"TRIP" menu
Press the "MENU" or "TRIP" button
to gain access to the general menu.
Select the "Trip computer" applica-
tion using the navigator, then coni rm.
The "Trip computer" menu offers
various options:
- Inputting of the distance to be travelled,
- Warnings log,
- Status of the functions. The different trip computer data also
appears on the instrument panel dis-
play at the same time.
Indication on the instrument
panel display

2
38
COLOUR SCREEN C
This displays the following information,
via the RD4 audio equipment control
pad:
- the time,
- the date,
- the exterior temperature (the value displayed l ashes if there is a risk
of ice),
- the accesses check,
- the vehicle functions warning or status messages, displayed tem-
porarily,
- the audio sources displays,
- the trip computer displays,
- the personalisation and coni gura- tion displays,
- the hands-free kit displays. Management of the displays
General menu
Press the
"MENU" button to gain
access to the general menu and
select one of the following functions:
- "Audio functions",
- "Trip computer",
- "Personalisation-Coni guration",
- "Telephone".

Example: "Audio functions" "Personalisation-Coni guration"
menu
This provides access to successive
coni rmation windows .
Dei ning the vehicle parameters
This enables you to activate or
deactivate certain driving and comfort
elements:
- "Automatic switching on of the
lights",
- "Follow-me-home lighting" and "Duration",
- "Remote control action",
- "Permanent locking of the boot".
The
"AUDIO" , "TRIP" and "TEL"
buttons on the RD4 audio equipment
control pad permit displaying in the
main window.

Example: "TRIP"

Example: "Automatic switching on of
the lights"

2
39
Selection of the language
German, Spanish, French, English,
Italian, Dutch, Portuguese and
Brazilian Portuguese.
Coni guration of the display
- "Setting the brightness-video".
- "Setting the date and time".
- "Selection of the units":

2
40
DT COLOUR AND MAP
SCREEN
This displays the following informa-
tion, via the RT3 GPS audio/telephone
control pad:
- the time,
- the date,
- the exterior temperature (the value displayed l ashes if there is a risk
of ice),
- the accesses check,
- the vehicle functions warning or status messages, displayed tem-
porarily,
- the audio sources displays,
- the telematic systems displays (telephone, services, ...),
- the trip computer displays,
- the coni guration displays,
- the satellite navigation system displays. Management of the displays
The
"AUDIO" , "NAV" , "TRIP" and

"TEL" buttons on the RT3 audio/
telephone control pad permit displaying
in the main window.
Example: "Coni guration"
"Coni guration" menu
The brightness of the display
and of the instrument panel
may change when the lights
are switched on automatically.
General menu
Press the
"MENU" button to gain access
to the general menu and select one of
the following functions:

- "Navigation-Guidance",
- "Audio functions",
- "Trip computer",
- "Coni guration",
- "Directory",
- "Telematics",
- "Map",
- "Video". This provides access to successive
coni rmation windows.

Example: "TRIP"