engine PEUGEOT 807 2002.5 Owner's Manual

YOUR 807 IN DETAIL91
Memorising using the buttons M,
1 and 2
T
o memorise using the buttons located
on the side of the seat: Place the ignition key in the 'running'
position (2 nd
notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off Briefly press button 1 or 2to recall
the corresponding memorised
position.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running Keep button 1 or 2pressed down
until the end of setting of the cor
responding memorised position.
Memorising seat and mirror
positions
Four driving positions can be memo
rised:
– two, using
two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front heated seat controls
The front seats can be heated sepa
rately.
Use the adjustment controls located
on the side of each seat to select the
level of heating required :
0:
Off.
1: Low.
2: Medium.
3: High.
The seat temperature is controlled
automatically.
Note: the heated seats only operate
with the engine running.
18-11-2002

YOUR 807 IN DETAIL
90
Front seats with electrical adjustment A Forwardsbackward
s adjustment
Push the control forwards or backwards to slide the seat.
B Driver's seat height adjustment Push the rear part of the control upwards or downwards to
obtain the required height.
C Seat back angle adjustment Tilt the control to the front or the rear to obtain the co rrect
angle.
D Driver's seat lumbar adjustment (mechanical) Raise or lower the lever to obtain the correct position.
E Head restraint height and angle adjustment To raise or lower the head restraint, pull forwards, at the
same time sliding it.
The setting is correct when the upper edge of the
head restraint is level with the top of the head.
To remove the head restraint, place it in the high position , lift
the tab using a coin and pull upwards and
forwards at the same time.
To reinstall, engage the head restraint rods in the holes,
making sure they are aligned with the seat back.
Never drive with the head restraints removed; they must be
in place and correctly adjusted.
F Rotating of seats (mechanical) Place the seat back in the upright position and move the
steering wheel forward.
Place the seat in the middle position on the runner andat maximum height.
On the driver's side, apply the handbrake, then release,
pulling on the end.
Pull the control upwards and rotate the seat inwards.
This rotating operation must be carried out with the engine
switched off.The passenger must not be facing the rear when the vehicle
is being driven.
Note: the electrical functions of the seats are cancelled one
minute after the ignition has been switched off.
18-11-2002

YOUR 807 IN DETAIL91
Memorising using the buttons M,
1 and 2
T
o memorise using the buttons located
on the side of the seat: Place the ignition key in the 'running'
position (2 nd
notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off Briefly press button 1 or 2to recall
the corresponding memorised
position.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running Keep button 1 or 2pressed down
until the end of setting of the cor
responding memorised position.
Memorising seat and mirror
positions
Four driving positions can be memo
rised:
– two, using
two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front heated seat controls
The front seats can be heated sepa
rately.
Use the adjustment controls located
on the side of each seat to select the
level of heating required :
0:
Off.
1: Low.
2: Medium.
3: High.
The seat temperature is controlled
automatically.
Note: the heated seats only operate
with the engine running.
18-11-2002

Removing a seat
Fold the corresponding seat.
Grasp the two bars Gunder the seat
and tighten them securely.
The front anchorages unlock.
Lift the seat and carry it using the
carrying handle H.
Refitting a seat
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat.
Locate the front anchorages in the
slides (if necessary tighten the two
bars Gsecurely).
Tilt the folded seat towards the rear.
The rear anchorages lock.
Lift the seat back (for the centre seat,
move control E) Turning a seat round
The rear seats can be placed in the
'rearwards facing' position.
For this, after the seat has been fold
ed, carry out the removal and replac
ing operations for the seat and turn it
round.
YOUR 807 IN DETAIL
94
Table position of the centre seat
Place the head restraint in the low
position.
Push control Eupwards.
Tilt the seat back forwards.
You now have a table with two cup
holders.
Folding the centre seat
Place the seat in the table position.
Lift control F
Place the seat in the closed position. This turning operation
must be carried out with
the engine switched off.
It is prohibited to sit facing
the rear when the vehicle
is being driven.
Never use the adjusting straps to
remove, refit or transport a seat.
When the vehicle is being driven,
it is prohibited to place a side seat
in the closed position, when a
passenger is sitting in the 3rd row.
18-11-2002

Note: the centre seat may be installed in the centre position of the 2nd row and in the left side position of the third row.
7
seats with access to 3 rd
row
8 seats with bench seat 5 seats with picnic position
"Cargo" configuration
YOUR 807 IN DETAIL
102
The various operations modifying the existing configuration must
be carried out with the engine switched off
(see section on ''Seats'').It is prohibited to be in a rearward s facing position when the vehicle is being driven.
18-11-2002

Changing the battery
of the remote control
The information "battery flat" is given
by an audible signal accompanied by
the message "Remote control bat
tery low" on the multi–function dis
play.
To replace the battery, unclip the
casing using a coin at the ring
(CR1620/3 volt battery).
If the remote control does not work
after the battery has been changed,
re programme the remote control.
Programming the remote
control
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again. CONFIDENTIAL CARD
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film, which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.
Key in ignition
The message
"Key in ignition" on
the multi–function display, accompa
nied by a buzzer on opening the
driver's door, indicates that the key
has been left in the ignition.
YOUR 807 IN DETAIL
104
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore
prevents starting of the vehicle by
anyone who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly,
the message "Antitheft
device fault" appears on the
multi–function display, accompanied
by an audible signal.
WARNING : your vehicle is no
longer protected.
Contact a PEUGEOT dealer as soon
as possible.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park :
 press button A. The courtesy
lights come on and the direction
indicators flash for a few seconds.
18-11-2002

YOUR 807 IN DETAIL105
Make a careful note of the number on each key. The key number i s coded on the label attached to the key. If
the key is lost, your PEUGEOT dealer can rapidly supply you with ne w keys.
The highfrequency remote control is a sensitive system; do not ope rate it while it is in your pocket as there is
a possibility that it may unlock your vehicle without your knowle dge.
The remote control cannot operate if the key is in the ignit ion, even if the ignition is switched off, except for reprogramming.
Do not operate the deadlock if there is someone inside the vehicle.
Driving with the doors locked or deadlocked may mean it is diffi cult for the emergency services to access the
passenge rcompartment in the event of an emergency.
As a safety measure (when there are children on board), remove the i gnition key when leaving the vehicle, even for a
short time.
Do not handle the buttons of your remote control when out of range of your vehicle, as you run the risk of stopping it
from working.
It would then be necessary to reprogramme the remote control.
When buying a secondhand car:
– Ensure that you are given the confidential card;
– have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones
that can start your vehicle.
Do not make any modifications to the electronic engine immobil iser system.
18-11-2002

Changing the battery
of the remote control
The information "battery flat" is given
by an audible signal accompanied by
the message "Remote control bat
tery low" on the multi–function dis
play.
To replace the battery, unclip the
casing using a coin at the ring
(CR1620/3 volt battery).
If the remote control does not work
after the battery has been changed,
re programme the remote control.
Programming the remote
control
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again. CONFIDENTIAL CARD
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film, which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.
Key in ignition
The message
"Key in ignition" on
the multi–function display, accompa
nied by a buzzer on opening the
driver's door, indicates that the key
has been left in the ignition.
YOUR 807 IN DETAIL
104
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore
prevents starting of the vehicle by
anyone who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly,
the message "Antitheft
device fault" appears on the
multi–function display, accompanied
by an audible signal.
WARNING : your vehicle is no
longer protected.
Contact a PEUGEOT dealer as soon
as possible.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park :
 press button A. The courtesy
lights come on and the direction
indicators flash for a few seconds.
18-11-2002

YOUR 807 IN DETAIL105
Make a careful note of the number on each key. The key number i s coded on the label attached to the key. If
the key is lost, your PEUGEOT dealer can rapidly supply you with ne w keys.
The highfrequency remote control is a sensitive system; do not ope rate it while it is in your pocket as there is
a possibility that it may unlock your vehicle without your knowle dge.
The remote control cannot operate if the key is in the ignit ion, even if the ignition is switched off, except for reprogramming.
Do not operate the deadlock if there is someone inside the vehicle.
Driving with the doors locked or deadlocked may mean it is diffi cult for the emergency services to access the
passenge rcompartment in the event of an emergency.
As a safety measure (when there are children on board), remove the i gnition key when leaving the vehicle, even for a
short time.
Do not handle the buttons of your remote control when out of range of your vehicle, as you run the risk of stopping it
from working.
It would then be necessary to reprogramme the remote control.
When buying a secondhand car:
– Ensure that you are given the confidential card;
– have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones
that can start your vehicle.
Do not make any modifications to the electronic engine immobil iser system.
18-11-2002

YOUR 807 IN DETAIL107
Electric sliding
side doors
Opening / Closing from the front:
– press the corresponding switch
B
to open or close.
An audible signal accompanies the
opening and closing of the door.
Opening / Closing from the
2 nd
row:
– press the corresponding switch C
to open or close.
Disarming the 2 nd
row controls:
– press the rear electric functions disarming switch.
THE DOORS
Opening the doors
from outside
Opening the doors
from inside
Note:
the door opening switches do
not function when the vehicle is
deadlocked. Locking / Unlocking from the
inside
Press button
A, the red warning light
comes on when the vehicle is locked
and switches off when it is unlocked.
This locks/unlocks the doors and the
tailgate.
Note: if the vehicle is locked or dead
locked from outside, the red warning
light flashes and button Adoes not
function. In this case, use the key or
the remote control for unlocking.
Automatic central locking
Your vehicle locks automatically
when you are driiving (at a speed of
more than 6 mph).
You can deactivate this function or
reactivate it.
To switch off
Press and hold button A.
Deactivation of the function is
accompanied by an audible signal.
To switch on
Press and hold button A.
Activation of the function is accom
panied by an audible signal and the
message ''Automatic locking of
the doors activated'' on the
multi–function display.
"Door open" alert
With the engine running or the vehicle
moving, a diagram accompanied by
an audible signal, locating the door
on the multi–function display, warns
you that a door is not properly closed.
18-11-2002