change time PEUGEOT 807 2002.5 Owners Manual

18-11-2002
YOUR 807 AT A GLANCE14REAR PARKING
ASSISTANCE
This system, installed in the rear
bumper, detects any obstacle
(person, vehicle, tree, barrier,
kerb, ...) behind the vehicle.
Switching on
With the engine running, the sys
tem is activated when reverse
gear is engaged. A bleep indi
cates that it is active.
The proximity information is
given by an audible signal, con
sisting of bleeps which becomes
more rapid as the vehicle
approaches the obstacle.
When the distance between the
rear of the vehicle and the obsta
cle is less than approximately
twentyfive centimetres, the audi
ble signal becomes continuous. ➜When you change to
neutral, the system
becomes inactive
again. TYRE UNDERINFLATION
DETECTION
Sensors check the pressure of
the tyres while driving and trigger
a warning in the event of a mal
function (speed above 15 mph
[25 km/h]).
Tyre(s) underinflated
When this message appears on
the multi–function display, accom
panied by an audible signal, have
the pressure of the tyres checked
as soon as possible.
Tyre(s) punctured
The appearance of this message,
accompanied by an audible sig
nal, is followed by illumination of
the
STOP warning light.
Stop immediately, avoiding any
sharp action on the steering
wheel or the brakes.
Change the damaged (punctured
or significantly underinflated)
wheel and have the pressure of
the tyres checked as soon as
possible.
Note: if the damaged wheel is
stored in the boot temporarily, it
will transmit this message again
as a reminder that it must be
repaired, which will prevent
another warning of the same type
being displayed.
The spare wheel does not have a
sensor. X type pressure sensor(s)
missing
The appearance of this message,
accompanied by an audible
warning, indicates that one wheel
(or more) is no longer detected.
Consult a PEUGEOT dealer to
have the faulty sensor(s)
replaced.
Warning:
this message is also
displayed when one of the
wheels is removed from the vehi
cle (for repair) or when a wheel is
fitted which is not equipped with
a sensor (winter tyres).
This system does not eliminate
the need to have the pressure
of the tyres checked regularly.
131141

YOUR 807 IN DETAIL
36
configuration (see corresponding
section).
map (see section "Satellite naviga tion system")
A few definitions
Superimposed display:
a window appears over the current
application for a short while, to
announce a change of status of
another application.
Permanent application:
main application currently in use,
displayed in the main screen win
dow.
Contextual menu:
limited menu associated with the
main application currently in use,
displayed in the main screen win
dow.
Colour screen DT
General menu
Press the
"MENU" button to access
the general menu and select one of
the following applications:
navigation guidance (see section "Satellite navigation system"),
trip computer (see corresponding section),
directory (see "RT3 audio/tele phone" section),
telematics (see "RT3 audio/tele phone" section),Parameter configuration
Monochrome screen B
Press button 1for two seconds to
gain access to the settings .
Then, each press of this button permits
scrolling of the various parameters.
– language of the information dis played,
– unit of speed (km or miles),
– unit of temperature (degrees Cel cius or Fahrenheit),
– time format (12 or 24 hours),
– hour,
– minute,
– year,
– month,
– day.
Pressing button 2enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After ten seconds without action, the
screen returns to the usual display,
the modified data are recorded.
18-11-2002

YOUR 807 IN DETAIL
36
configuration (see corresponding
section).
map (see section "Satellite naviga tion system")
A few definitions
Superimposed display:
a window appears over the current
application for a short while, to
announce a change of status of
another application.
Permanent application:
main application currently in use,
displayed in the main screen win
dow.
Contextual menu:
limited menu associated with the
main application currently in use,
displayed in the main screen win
dow.
Colour screen DT
General menu
Press the
"MENU" button to access
the general menu and select one of
the following applications:
navigation guidance (see section "Satellite navigation system"),
trip computer (see corresponding section),
directory (see "RT3 audio/tele phone" section),
telematics (see "RT3 audio/tele phone" section),Parameter configuration
Monochrome screen B
Press button 1for two seconds to
gain access to the settings .
Then, each press of this button permits
scrolling of the various parameters.
– language of the information dis played,
– unit of speed (km or miles),
– unit of temperature (degrees Cel cius or Fahrenheit),
– time format (12 or 24 hours),
– hour,
– minute,
– year,
– month,
– day.
Pressing button 2enables you to
change the parameter selected.
Continue pressing the button for
rapid scrolling.
After ten seconds without action, the
screen returns to the usual display,
the modified data are recorded.
18-11-2002

44
YOUR 807 IN DETAIL
GENERAL FUNCTIONS On/off
With the ignition key in the accessories or ignition position , press button Mto switch the set on or off.
The set can operate for 30 minutes without the vehicle ign ition being switched on.
Antitheft system
The audio system is coded in such a way that it can operate on ly on your vehicle. It would not function if fitted to another
vehicle.
The antitheft system is automatic and requires no action on your part.
ADJUSTING THE VOLUME
Press button Oto increase the volume, or button Nto decrease it.
Continuous pressure on buttons Oand Nallows a gradual adjustment of the volume.
AUDIO SETTINGS Press button G several times in succession to access the bass ( BASS), treble(TREB), loudness (LOUD),
fader (FAD) , balance ( BAL)and automatic volume correction.
Exit from audio mode is automatic after a few seconds without p ressing any button, or by pressing button G
after configuration of the automatic volume correction.
Note: bass and treble settings are specific to each source. It is possibl e to set them differently for radio, cas
sette (RB3) , CD (RD3) and CD changer.
18-11-2002

YOUR 807 IN DETAIL
52
CD CHANGER
Selecting CD changer mode Audio RB3:press button "SRC" several times in succession.
Audio RD3: press button R.
Selecting a disc
Press buttons "1"to "6" of the radio to select the corresponding disc.
Selecting a track Press button Ito select the next track.
Press button Jto return to the start of the current track or to select the previ ous track.
Accelerated play
Keep button Ior Jpressed for forwards or backwards accelerated play.
Accelerated play stops as soon as the button is released.
Shuffle
When the CD changer is selected:
– audio RB3: keep button "SRC" pressed for two seconds;
– audio RD3: keep button R pressed for two seconds.
The tracks will be played in random sequence. Pressing the butto n again for two seconds returns you to normal play.
18-11-2002

YOUR 807 IN DETAIL63
COMPACT DISC CHANGER
Selecting CD changer mode Press the ''SOURCE'' button several times.
Selecting a disc
Press press one of the buttons ''1''to''6'' of the audio/telephone to select the apropriate disc.
Buttons H and Iallow you to select the previous or following track of the cha nger respectively.
Selecting a track Press button Mto select the following track.
Press button Nto return to the start of the current track or to select the previ ous track.
Accelerated play
Press and hold button M or Nfor forwards or backwards accelerated play.
Accelerated play stops as soon as the button is released.
Contextual menu
The contextual menu permits you to switch the shuffle function s on or off, to play the
start of a track or to repeat a track.
18-11-2002

YOUR 807 IN DETAIL
76
Select the Navigation/Guidance icon
using the dial, then validate by
pressing the dial to access the main
"Navigation Guidance"menu.
General menu
Switch on the RT3 audio/telephone
and insert the navigation CD ROM.
Press the "MENU"button to access
the general menu .
During guidance, if the navigation CDROM is present, the scre en displays dif
ferent information depending on the manoeuvres to be carried out.
1. Current manoeuvre or compass.
2. Next manoeuvre to be carried out.
3. Next road to be taken.
4. Current road.
5. Estimated time of arrival at destination.
6. Distance to final destination.
7. Distance to next manoeuvre.
Notes:
depending on the situation of the vehicle and on the reception of the GPS
information, this information may disappear from the screen tempora rily,
during guidance, it is only possible to listen to a CD if the vehicle is fitted with
a CD changer.
General notes on the display
12
765
13
654
4
3
Monochrome screen CT Colour screen DT
2
7
18-11-2002

YOUR 807 IN DETAIL
80
Select the ''Directory'' function to
access the file in which the address
you are looking for is archived.
Select a description by scrolling
down the list by means of the dial,
then confirm by pressing the dial.
The directory file is then displayed.
Select the "OK" function, then press
the dial to access the guidance acti
vation function.
Follow the directions given by the
system.
Selecting a destination stored in
the directory
Select the
"Most recent destina
tions" function to access one of the
last ten addresses stored.
Select a description by scrolling
down the list by means of the dial,
then confirm it by pressing the dial.
The complete address is then dis
played.
Select the "OK" function, then press
the dial to access the guidance acti
vation function.
Follow the instructions given by
the system.
Selection of one of the last ten
destinationsActivate the function
''Changing the
route'' , then input the distance
involved in the change required.
Select the ''OK''function then vali
date by pressing the dial.
The system calculates the change
which is closest to the value input
and gives you the option of whether
or not to use this change.
Details of the route
You can consult the destination
address at any time by activating the
"Chosen destination" function.
Changing the initial route
18-11-2002

YOUR 807 IN DETAIL91
Memorising using the buttons M,
1 and 2
T
o memorise using the buttons located
on the side of the seat: Place the ignition key in the 'running'
position (2 nd
notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off Briefly press button 1 or 2to recall
the corresponding memorised
position.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running Keep button 1 or 2pressed down
until the end of setting of the cor
responding memorised position.
Memorising seat and mirror
positions
Four driving positions can be memo
rised:
– two, using
two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front heated seat controls
The front seats can be heated sepa
rately.
Use the adjustment controls located
on the side of each seat to select the
level of heating required :
0:
Off.
1: Low.
2: Medium.
3: High.
The seat temperature is controlled
automatically.
Note: the heated seats only operate
with the engine running.
18-11-2002

YOUR 807 IN DETAIL91
Memorising using the buttons M,
1 and 2
T
o memorise using the buttons located
on the side of the seat: Place the ignition key in the 'running'
position (2 nd
notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off Briefly press button 1 or 2to recall
the corresponding memorised
position.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running Keep button 1 or 2pressed down
until the end of setting of the cor
responding memorised position.
Memorising seat and mirror
positions
Four driving positions can be memo
rised:
– two, using
two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front heated seat controls
The front seats can be heated sepa
rately.
Use the adjustment controls located
on the side of each seat to select the
level of heating required :
0:
Off.
1: Low.
2: Medium.
3: High.
The seat temperature is controlled
automatically.
Note: the heated seats only operate
with the engine running.
18-11-2002