lights PEUGEOT 807 2002 User Guide

Changing the battery
of the remote control
The information "battery flat" is given
by an audible signal accompanied by
the message "Remote control bat
tery low" on the multi–function dis
play.
To replace the battery, unclip the
casing using a coin at the ring
(CR1620/3 volt battery).
If the remote control does not work
after the battery has been changed,
re programme the remote control.
Programming the remote
control
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again. CONFIDENTIAL CARD
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film, which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.
Key in ignition
The message
"Key in ignition" on
the multi–function display, accompa
nied by a buzzer on opening the
driver's door, indicates that the key
has been left in the ignition.
YOUR 807 IN DETAIL
104
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore
prevents starting of the vehicle by
anyone who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly,
the message "Antitheft
device fault" appears on the
multi–function display, accompanied
by an audible signal.
WARNING : your vehicle is no
longer protected.
Contact a PEUGEOT dealer as soon
as possible.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park :
 press button A. The courtesy
lights come on and the direction
indicators flash for a few seconds.
18-11-2002

THE ALARM
This provides two types of protection:
– exterior protection: it sounds if adoor, the tailgate, the bonnet or a
sunroof is opened.
– interior protection: it sounds if the volume inside the passenger com
partment changes (breaking of a
window or a movement inside the
vehicle).
Setting the alarm  Switch off the ignition and get out
of the vehicle.
 Set the alarm within five minutes
of getting out of the vehicle, by
locking or deadlocking using the
remote control (the red indicator
light, located in the centre of the
fascia and visible from the out
side, flashes once per second). Note:
if you wish to lock your vehicle
without setting the alarm, use the
door lock.
When the alarm is triggered, the
siren sounds and the direction indi
cator lights flash for thirty seconds.
After triggering, the alarm remains
set.
Warning: if the alarm has been trig
gered ten times in succession, on
the eleventh time it becomes inac
tive.
Note: if the red warning light, located
in the centre of the fascia, flashes
rapidly, the alarm has been triggered
while you were away from your vehi
cle. To stop it flashing, insert the
remote control key and switch on the
ignition.
Disarming
Unlock the vehicle with the remote
control key (the red indicator light,
located in the centre of the fascia,
goes out).
To set the alarm with exterior
protection only
If, while you are away from the vehi
cle, you wish to leave a window
partially open or a pet inside the
vehicle, you should choose exterior
protection only.
 Close the sunroofs, 
Switch off the ignition,
 In the next ten seconds, press
button A, located on the lefthand
side of the fascia, until the red
indicator light is on continuously,
 Get out of the vehicle,
 Within the next five minutes, set
the alarm by locking or deadlock
ing using the remote control (the
red indicator light, located in the
centre of the fascia, flashes once
a second).
Note: when the alarm is set but the
remote control does not operate:
 Unlock the doors with the key and
open the door. The alarm is
triggered.
 Switch on the ignition in the next
ten seconds. The alarm is dis
armed.
Incorrect operation
When the ignition is switched on, if
the red indicator light, located in the
centre of the fascia, comes on for ten
seconds, there is a fault in the siren
connection.
Contact a PEUGEOT dealer to have
the system checked.
Do not make any modifi
cations to the alarm sys
tem as this could cause
faults.
YOUR 807 IN DETAIL
106
18-11-2002

Direction indicators
(flashers)Left:downwards.
Right: upwards.
YOUR 807 IN DETAIL
112
LIGHTING CONTROL
Front and rear lights
Selection is by turning ring
A.
Lights off
Side lights on Dipped beam/Main
beam
Automatic switching
on of lights Dipped beam/main beam change
Pull the stalk fully towards you.
Lightson buzzer
When the ignition is switched off,
when the driver's door or front pas
senger door is opened, a buzzer
sounds, accompanied by the mes
sage
"Side lights on" on the
multi–function display if you have left
your lights on.
Front and rear fog lights
Rotate ring Bforwards to switch on
and rearwards to switch off. The sta
tus is confirmed by the light on the
instrument panel.
Front fog lights (1 st
rotation
of the ring forwards)
These operate with the side lights
and the dipped beam headlamps. Front and rear fog
lights (2nd
rotation of
the ring forwards) These operate with the side lights
and the dipped beam headlamps.
Note:
to switch off the front and rear
fog lights, turn the ring rearwards
twice in succession.
In clear weather or in
rain, both day and night,
rear fog lights dazzle and
are prohibited.
Do not forget to switch
them off when they are no longer
needed.
Automatic switching on of the
lights switches off the rear fog
lamps, but the front fog lamps
remain on.
18-11-2002

AUTOMATIC SWITCHING ON
OF LIGHTS
Side lights and dipped beam head
lamps switch on automatically if the
light is poor, or during continuous
operation of the windscreen wipers.
They switch off when the light
becomes bright enough or the wind
screen wipers stop.
Note: In foggy weather, the bright
ness sensor can detect sufficient
light. As a consequence, the lights
will not come on automatically.
This function is active when the
vehicle is supplied to the customer.
To disarm or activate the function :  Start with the key in the acces
sories position (1st notch),
 Place the lights stalk in position 0,
 Press the end of the stalk for more
than two seconds.
Note: after the ignition is switched off
and depending on the brightness,
the lights remain on for approximate
ly 45 seconds or until the vehicle is
locked.
Do not cover the brightness sen
sor located in the centre of the
fascia. It is used for automatic
switching on of the lights. Operating check
Activation
Activation of this function is accom
panied by an audible signal and the
message
"Automatic lighting
active" on the multi–function dis
play .
Disarming
Disarming of the function is accom
panied by an audible signal.
Note: the function is disarmed
temporarily when the driver uses the
manual lighting controls.
YOUR 807 IN DETAIL 113
18-11-2002

YOUR 807 IN DETAIL
118
Trip computer configuration
This function allows inputting of the
distance to the destination (when
guidance is not activated; otherwise
the information is given by the navi
gation) and also changing of the
units (°C or °F, km and litres or miles
and gallons).
Diagnostics
This function tells you the warnings,
the quantity of emergency fuel and
the GPS cover present at the time
consulted.
Note:
these warnings have previous
ly been displayed in the form of mes
sages and/or warning lights on the
control unit.
There are 6 categories of diagnostics :
engine diagnostics (warnings linked to the engine, gearbox
etc....),
brake diagnostics,
suspension diagnostics (warnings linked to the suspension, ESP
etc....),
wheel diagnostics (warnings linked to tyres),
door and window diagnostics,
passenger compartment diagnos tics. Distance to destination
When guidance is not activated, this
enables an approximate value to be
entered to make all the trip computer
calculations possible.
Specific features of the
monochrome screen CT and
the colour screen DT
General menu
Press the
"MENU"button to access
the general menu.
Select the icon ''Trip computer''
using the dial, then validate to
access the ''Trip computer'' menu.
The ''trip computer'' menu offers var
ious choices:
Trip computer configuration,
Diagnostics.
'Trip computer' context menu
The context menu associated with
the "Trip Computer" application
appears as a superimposed display
when the Trip Computer is the appli
cation currently being used in the
main screen window.
Briefly press the continuous applica
tion 'Trip computer' button to select
one of the following functions:
Warnings log,
Distance to destination.
18-11-2002

Horn
Press one of the spokes or
the centre of the steering
wheel.
YOUR 807 IN DETAIL
122
Manual adjustment of the
headlamps
Depending on the load in your vehi
cle, adjusting the beam of your head
lamps is recommended.
0 1 or 2 people in the front seats.
1 5 people.
2 6 to 8 people.
3 Driver + maximum authorised
loads.
Initial setting is position 0.
Automatic adjustment of
headlamps
Refer to the paragraph on Lighting
under the section entitled 'Towing a
trailer...'. Hazard warning lights
Press the button, the direction indi
cators flash.
They can operate with the ignition
off.
Steering wheel height and
depth adjustment
When the vehicle is stationary,
unlock the steering wheel by lower
ing the lever
A.
Adjust the height and depth of the
steering wheel, then lock by pushing
lever Afully upwards.
Automatic lighting of hazard
warning lights*
When braking in an emergency,
depending on the force of decelera
tion, the hazard warning lights come
on automatically. They switch off
automatically the first time you accel
erate.
It is also possible to switch them off
by pressing the button on the fascia.
*According to destination.
18-11-2002

YOUR 807 IN DETAIL123
COURTESY LIGHTS
Off.
Comes on on opening one of the doors.
Permanently on, with the key in the accessories position or the i gnition on.
1 Front courtesy light
2 2nd row rear courtesy light
3 3rd row rear courtesy light
4 Front map reading lights
5 2nd row rear map reading lights
6 3rd row rear map reading lights The front and rear courtesy lights
come on when the ignition key is
removed, on unlocking the vehicle or
on opening one of the doors.
They gradually go off after the igni
tion has been switched on
, after the
vehicle is locked or after the last door
is closed.  With the ignition off, pressing
switch 1turns on the front
and rear courtesy lights for ten
minutes.
 With the ignition off, pressing
switch 2 or 3 turns on the corre
sponding rear courtesy light for
ten minutes.
The front and rear map reading lights
are switched on by operating the cor
responding switch. These are active
when the key is in the accessories
position (1st notch) or the ignition is
on.
18-11-2002

YOUR 807 IN DETAIL125
INTERIOR LAYOUT
1. Spectacles holder
2. Glove box To open the glove box, press the
button.
To close it, press the lid.
It has dedicated compartments
for storing a pen, a mobile tele
phone, a pair of spectacles,
coins or tokens and credit cards.
3. Audio equipment concealing flap
Lower the flap fully to lock it.
Press the flap to raise it.
4. Central storage compartment
5. Passenger upper glove box To open the glove box, press the
button.
To close it, press the lid.
It has dedicated compartments
for storing a pair of spectacles,
keys, five audio CDs and four
audio cassettes or nine audio
CDs. 6. Passenger lower glove box
This is fitted with a lock.
To open the glove box, lift the
handle.
The glove box lights when the lid
is opened.
It contains three sockets for
connecting video equipment.
It has dedicated compartments
for storing maps, a packet of
cigarettes, an A4 format docu
ment, etc.
7. Lighter or 12 volt accessories socket
8. Cooled compartment This can hold up to three cans.
Turn the closer, at the top, to
open or close the air feed.
9. Can holder and ashtray This retractable support, with
light, contains up to two can
holders, a removable ashtray
and a location for the lighter
when it is used as a 12V socket. 10. Storage compartment or
remote control keypad
The storage compartment must
not be used as an ashtray.
11. Storage
12. Door tray with storage compartment for a bottle
of water
13. Instrument panel fuse box
18-11-2002

YOUR 807 IN DETAIL135
Disarming the passenger
air bag*
To ensure the safety of your child,
it is essential to disarm the pas
senger air bag when you install a
rearfacing child seat on the front
passenger seat. 
With the ignition switched off,
insert the key into the passenger
air bag disarming switch 1, turn it
to the "OFF" position, then
remove the key keeping the slot
in this position.
The air bag warning light on the
instrument panel is lit throughout the
disarming process. In the
"OFF" position, the passenger
air bag will not be triggered in the
event of an impact.
As soon as the child seat is
removed, turn the air bag slot to the
"ON" position to reactivate the air
bag and thus ensure the safety of
your passenger in the event of an
impact.
Operating check
This is confirmed by an indicator
light, accompanied by an audible
signal and a message on the multi
function display.
With the ignition on (2nd
notch), illumination of this
warning light accompanied
by an audible signal and the
message "Passenger air
bag disarmed" on the
multifunction display, indicates that
the passenger air bag is disarmed
(switch in the "OFF" position). SIDE AIR BAGS AND
CURTAIN AIR BAGS
The side air bags are incorporated
into the front seat backs on the door
side.
The curtain air bags are incorporated
into the door pillars and the upper
part of the passenger compartment.
They are deployed independently of
each other depending on which side
the collision occurs.
Operating check
This is confirmed by an indi
cator light, accompanied by
an audible signal and a
message on the multi–func
tion display.
If this indicator light comes on,
accompanied by an audible signal
and the message "Air bag fault" on
the multi–function display, contact a
PEUGEOT dealer to have the sys
tem checked.
* According to destination. If
the two "Air bag fault" and "Passenger air bag disarmed" warning
lights come on permanently, do not install a rearward facing child seat
and consult a PEUGEOT dealer.
18-11-2002

YOUR 807 IN DETAIL135
Disarming the passenger
air bag*
To ensure the safety of your child,
it is essential to disarm the pas
senger air bag when you install a
rearfacing child seat on the front
passenger seat. 
With the ignition switched off,
insert the key into the passenger
air bag disarming switch 1, turn it
to the "OFF" position, then
remove the key keeping the slot
in this position.
The air bag warning light on the
instrument panel is lit throughout the
disarming process. In the
"OFF" position, the passenger
air bag will not be triggered in the
event of an impact.
As soon as the child seat is
removed, turn the air bag slot to the
"ON" position to reactivate the air
bag and thus ensure the safety of
your passenger in the event of an
impact.
Operating check
This is confirmed by an indicator
light, accompanied by an audible
signal and a message on the multi
function display.
With the ignition on (2nd
notch), illumination of this
warning light accompanied
by an audible signal and the
message "Passenger air
bag disarmed" on the
multifunction display, indicates that
the passenger air bag is disarmed
(switch in the "OFF" position). SIDE AIR BAGS AND
CURTAIN AIR BAGS
The side air bags are incorporated
into the front seat backs on the door
side.
The curtain air bags are incorporated
into the door pillars and the upper
part of the passenger compartment.
They are deployed independently of
each other depending on which side
the collision occurs.
Operating check
This is confirmed by an indi
cator light, accompanied by
an audible signal and a
message on the multi–func
tion display.
If this indicator light comes on,
accompanied by an audible signal
and the message "Air bag fault" on
the multi–function display, contact a
PEUGEOT dealer to have the sys
tem checked.
* According to destination. If
the two "Air bag fault" and "Passenger air bag disarmed" warning
lights come on permanently, do not install a rearward facing child seat
and consult a PEUGEOT dealer.
18-11-2002