bulb PEUGEOT 807 2002 Owners Manual

PRACTICAL INFORMATION
144
CHANGING A BULB
Front lights
Note:
handle the bulbs with a dry cloth.
1 Dipped beam headlamps: H755W or xenon bulb.
2 Main beam headlamps: H755W or xenon bulb.
3 Fog lamps: H155W.
Note : make access on the righthand side easier by remo
ving the fuse box cover.
Turn the protective cover corresponding to the faul
ty bulb a quarter of a turn and remove it.
 Disconnect the connector.
 Press the end of the securing clip to free it. Change
the bulb. When fitting the new bulb, ensure that the
direction notches are positioned correctly and the
securing clip is fixed properly.
 Reconnect the connector.
 Refit the protective cover, then turn it a quarter of a
turn to the right. The headlamps are fitted with polycarbonate glass with a
protective coating.
Do not clean them with a dry or abra
sive cloth, nor with a detergent or solvent product. Use
a sponge and soapy water.
4 Side lights: W 5 W.
 Push the light from the inside towards the outside of
the bumper.
 Pull the light forwards.
 Turn the bulb holder a quarter turn to the left and
remove it.
 Turn the bulb a quarter turn to the left, remove it and
change it.
When refitting, engage the light towards the outsi
de and move it towards the inside of the bumper.
5 Direction indicators: PY 21 W (amber).F
 Turn the bulb holder a quarter of a turn to the left
and remove it.
 Change the bulb.
Note: In certain climatic conditions (low temperature,
humidity), condensation inside the headlamp glass is
normal ; it disappears a few minutes after the lights are
switched on.
WARNING: RISK OF ELECTROCUTION
Xenon bulbs must be changed by a PEUGEOT dealer.
18-11-2002

Direction indicator repeaters:
WY 5 W (amber). Push the repeater rearwards and
release it from the mirror.
 Hold the connector and turn the
bulb holder a quarter turn to the
left.
 Turn the bulb a quarter turn to
the left, remove it and change it.
When refitting, engage the
repeater towards the rear and
move it towards the front of the
mirror. Rear lights
1 Direction indicators:
PY 21 W
(amber) .
2 Brake/side lights: P 21/5 W.
3 Reversing lights: P 21 W.
4 Fog lamps: P 21 W.
These 4 bulbs are changed from
inside the vehicle:  open the tailgate,
 remove the air extraction grille on
the side concerned,
 unclip the light harness,
 unscrew the two interior nuts and
remove the light,
 unscrew the bulb holder concer
ned an eighth turn to the left and
remove it,
 unscrew the faulty bulb an eighth
turn to the left and change it. When refitting: 
take care to position the bulb cor
rectly and press on it to engage it,
 take care to position the bulb hol
der correctly and press on it to
engage it,
 take care to position and secure
the light correctly.
Number plate lights:
W 5 W  Remove the lens.
 Change the faulty bulb.
PRACTICAL INFORMATION 145
Third brake light:
5 W 5 W bulbs.  Remove the tailgate upper trim by
unclipping it on either side.
 Squeeze the two tabs 1to release
the bulb holder.
 Change the faulty bulb.
 When refitting, ensure that the
tailgate upper trim has been put
back in place correctly.
Note: when two or more bulbs are
faulty, you must replace them imme
diately.
Amber coloured bulbs
(direction indicators and
side repeaters), must be
changed for bulbs of iden
tical specification and
colour.
18-11-2002

Direction indicator repeaters:
WY 5 W (amber). Push the repeater rearwards and
release it from the mirror.
 Hold the connector and turn the
bulb holder a quarter turn to the
left.
 Turn the bulb a quarter turn to
the left, remove it and change it.
When refitting, engage the
repeater towards the rear and
move it towards the front of the
mirror. Rear lights
1 Direction indicators:
PY 21 W
(amber) .
2 Brake/side lights: P 21/5 W.
3 Reversing lights: P 21 W.
4 Fog lamps: P 21 W.
These 4 bulbs are changed from
inside the vehicle:  open the tailgate,
 remove the air extraction grille on
the side concerned,
 unclip the light harness,
 unscrew the two interior nuts and
remove the light,
 unscrew the bulb holder concer
ned an eighth turn to the left and
remove it,
 unscrew the faulty bulb an eighth
turn to the left and change it. When refitting: 
take care to position the bulb cor
rectly and press on it to engage it,
 take care to position the bulb hol
der correctly and press on it to
engage it,
 take care to position and secure
the light correctly.
Number plate lights:
W 5 W  Remove the lens.
 Change the faulty bulb.
PRACTICAL INFORMATION 145
Third brake light:
5 W 5 W bulbs.  Remove the tailgate upper trim by
unclipping it on either side.
 Squeeze the two tabs 1to release
the bulb holder.
 Change the faulty bulb.
 When refitting, ensure that the
tailgate upper trim has been put
back in place correctly.
Note: when two or more bulbs are
faulty, you must replace them imme
diately.
Amber coloured bulbs
(direction indicators and
side repeaters), must be
changed for bulbs of iden
tical specification and
colour.
18-11-2002

TOWING A TRAILER,
CARAVAN, BOAT ETC...
Only use original PEUGEOT tow
bars which have been tested and
approved from the design stage of
your vehicle.
The tow bar must be fitted by a
PEUGEOT dealer.
Driving advice
Distribution of loads: distribute the
load in the trailer so that the heaviest
loads are as close as possible to the
axle and the nose weight is close to
the maximum authorised without,
however, exceeding it.
Cooling: towing a trailer on a slope
increases the coolant temperature.
As the fan is electronically con
trolled, its cooling capacity is not
dependent on the engine speed.
On the contrary, use a high gear to
lower the engine speed, and reduce
your speed.
In all cases, pay attention to the
coolant temperature. Note:
in certain cases of particularly
arduous use (towing the maximum
load up a steep slope in high tem
peratures), the engine automatically
limits its power. In this case, cutting
off the air conditioning allows the
engine power to be recovered, and
therefore the towing speed to be sig
nificantly increased (approximately
12mph [20 km/h] more).
If the coolant temperature warning
light comes on, stop the vehicle and
switch off the engine as soon as pos
sible.
Tyres: check the tyre pressures
of the towing vehicle and of the trail
er, observing the recommended
pressure.
Brakes: towing increases the brak
ing distance. Drive at a moderate
speed, change down early and brake
gradually.
Side wind: sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed. Lighting
Manual adjustment
Adjust your headlamps so as not to
dazzle other road users (see section
on ''Manual adjustment of head
lamps''). Check the electrical sig
nalling of the trailer.
Automatic beam correction
For vehicles with Xenon bulbs, this
system automatically corrects the
height of the beam, whatever the
load of the vehicle. The driver is then
assured of having optimum lighting
and not causing a nuisance to other
road users.
PRACTICAL INFORMATION
155
18-11-2002