turn signal PEUGEOT 807 2002 Owners Manual

YOUR 807 AT A GLANCE11
CRUISE CONTROL
The cruise control makes it possi
ble to maintain a constant vehicle
speed programmed by the driver
(above 25 mph [40 km/h] with 4 th
or 5 th
gear engaged), without the
accelerator pedal being pressed.
Switching on
➜Place the knob 1in the
ON position. The
warning light comes
on, accompanied by
an audible signal.
Storing a speed
➜Press button 2 or 3 to store the
speed at which you are driving.
➜Press button 2to reduce the
stored speed or button 3to
increase it.
Deactivating the stored speed
➜Press button 4 or the brake or
clutch pedal. Recalling the stored speed
➜Press button
2 or 3.
Cancelling the stored speed
➜Place the knob 1in the OFF
position.
Note: the stored speed is can
celled when the ignition is
switched off.
FRONT, SIDE AND
CURTAIN AIR BAGS
Disarming the passenger air
bag*
➜With the ignition off, insert the
key into control 1and turn it:
– "ON" position, passenger air
bag activated,
– "OFF" position, passenger air
bag disarmed. Precautions regarding the
passenger air bag
➜activate the
air bag for an
adult passen
ger,
➜disarm the
air bag if you
install a rear
facing child
seat.
Do not place your feet or any
object on the instrument panel.
Operating check When the passenger air
bag is disarmed, the
warning light comes on
when the ignition is
switched on (2 nd
key
notch), accompanied by an audi
ble signal and the message
"Passenger air bag disarmed" .
Air bag fault
If this warning light
comes on, accompanied
by an audible signal and
the message "Air bag
fault" , consult a
PEUGEOT dealer to
have the system
checked.
* According to country.
134
18-11-2002

INSTRUMENTS AND CONTROLS
28
INSTRUMENTS AND CONTROLS
A warning light continuously lit, or flashing with the eng ine running, is an indication of a malfunction in the
relevant unit. Some warning lights may be linked to buzzer s and a message on the multi–function display. Do not
ignore this warning: contact a PEUGEOT dealer as quickly a s possible.
If the central STOP warning light comes on when you are d riving, stop immediately where it is safe to do so.
Central STOP warning light
This is linked to the "engine oil pressure", "coolant level low " and "brake fluid level" warning lights and the coolant
temperature gauge and puncture warnings, indicated by a message on the multifunction display.
It comes on each time the ignition is switched on.
Stop immediately .
Contact a PEUGEOT dealer.
Engine oil pressure warning light
This is linked to the central STOPwarning light.
If it comes on with the engine running, it is accompanied b y an audible signal and the message "Oil pressure low"
or "Top up engine oil" on the multifunction display.
Stop immediately .
In the case of a lack of oil in the lubricating circuit, top up the level.
Contact a PEUGEOT dealer without delay.
Low coolant level warning light
This is linked to the central STOPwarning light.
It comes on each time the ignition is switched on.
Illumination of this warning light, with the engine run ning, is accompanied by an audible signal and the message
"Top up coolant" on the multifunction display.
Stop immediately.
Warning: allow the engine to cool before topping up.
The cooling system is pressurised.
To prevent the risk of scalding, unscrew the cap by two turns to allow the pressure to drop.
Once the pressure has dropped, remove the cap and topup the le vel.
Contact a PEUGEOT dealer.
18-11-2002

INSTRUMENTS AND CONTROLS
32
In zoneA,the temperature is correct.
In zone B, the temperature is too high. The central STOPwarning light and the
maximum coolant temperature warning light 1come on, accompanied by an
audible signal and the message "Coolant temp. too high"on the multifunction
display.
You must stop immediately.
Warning : wait for the engine to cool before topping up the le vel.
The cooling system is pressurised.
In the event of a breakdown and in order to avoid any risk of scalding, unscrew
the cap two turns to allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer.
Instrument panel with
monochrome screen
Instrument panel with colour
screen
Coolant temperature indicator light
18-11-2002

YOUR 807 IN DETAIL47
Manual station search
Press the "MAN"button.
Briefly press button Ior Jto increase or decrease the frequency displayed.
By continuing to press the button in the direction selected, you will obtain continuous scrolling of the frequency.
The scrolling stops at the first station found as soon as the button is released.
Pressing the "MAN"button again returns you to automatic station search.
Manual storing of stations in the memory
Select the station required.
Press one of the buttons "1"to "6" for more than two seconds.
The sound stops then becomes audible again, confirming that the station has been stored in the memory.
Automatic storing of FM stations in the memory (autostore)
Audio RB3:press and hold the "BND/AST" button for more than two seconds.
Audio RD3: press and hold button "P" for more than two seconds.
Your radio automatically stores the 6 stations with the stronge st signal in FM. These stations are stored in the FMast wave
band.
If it is not possible to find 6 stations, the remaining memo ries are empty.
Recalling stations stored in the memory
For each waveband, briefly press buttons "1"to "6" to recall the corresponding station.
18-11-2002

YOUR 807 IN DETAIL47
Manual station search
Press the "MAN"button.
Briefly press button Ior Jto increase or decrease the frequency displayed.
By continuing to press the button in the direction selected, you will obtain continuous scrolling of the frequency.
The scrolling stops at the first station found as soon as the button is released.
Pressing the "MAN"button again returns you to automatic station search.
Manual storing of stations in the memory
Select the station required.
Press one of the buttons "1"to "6" for more than two seconds.
The sound stops then becomes audible again, confirming that the station has been stored in the memory.
Automatic storing of FM stations in the memory (autostore)
Audio RB3:press and hold the "BND/AST" button for more than two seconds.
Audio RD3: press and hold button "P" for more than two seconds.
Your radio automatically stores the 6 stations with the stronge st signal in FM. These stations are stored in the FMast wave
band.
If it is not possible to find 6 stations, the remaining memo ries are empty.
Recalling stations stored in the memory
For each waveband, briefly press buttons "1"to "6" to recall the corresponding station.
18-11-2002

When this warning light
comes on, connected to the
STOPwarning light,
accompanied by a buzzer
and the message "Braking
fault" , it indicates that there is a mal
function of the electronic brake force
distribution, which can cause a loss of
control of the vehicle when braking.
Stop immediately.
In both cases, consult a Peugeot
dealer.
ANTILOCK BRAKING
SYSTEM (ABS) AND THE
ELECTRONIC BRAKE FORCE
DISTRIBUTION (EBFD)
The ABS, in conjunction with the elec
tronic brake force distribution, increas
es the stability and manoevrability of
your vehicle, particularly on poor or
slippery road surfaces.
Note: when changing wheels (tyres
and rims), make sure that these are
approved.
The antilock braking system comes
into operation automatically when
there is a risk of wheel lock.
When this warning light
comes on, accompanied by
a buzzer and the message
"ABS fault" , it indicates
that there is a malfunction
of the ABS, which can cause a loss
of control of the vehicle when brak
ing.
YOUR 807 IN DETAIL
128
To return to normal operation, pull
the lever upwards until a click is
heard.Illumination of this light,
accompanied by an audible
signal and the message
"handbrake on" on the
multi–function display, indi
cates that the handbrake is still on or
has not been properly released.
HANDBRAKE
Applying
When parking, pull the handbrake to
immobilize your vehicle.
Warning : when parking on a slope,
direct your wheels towards the pave
ment and pull the handbrake.
Releasing
Pull on the handle and press the but
ton to release the handbrake.
Disengaging
Apply the handbrake.
Pull the button located at the end of
the handbrake forwards.
The handbrake lever lowers.
You can now pivot the seat. EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system
enables the optimum braking pres
sure to be reached more quickly,
thus reducing the stopping distance.
It is triggered according to the speed
of activation of the brake pedal. The
effect of this is a reduction in the
resistance of the pedal and an
increase in braking efficiency. Normal operation of the ABS may
make itself felt by slight vibrations
of the brake system.
In emergency braking, press
very firmly without releasing
the pressure.
18-11-2002

YOUR 807 IN DETAIL133
Automatic operation
Automatic changing of the four
gears:  select function D in the gate.
The gearbox always selects the
most suitable gear according to the
following parameters:
the style of driving,
the road profile,
the vehicle load.
The gearbox is then operating in
autoadaptive mode, without any
action on your part.
WARNING
Never select function N when the
vehicle is moving.
Never select functions Por Runless
the vehicle is stationary.
Never change between functions to
optimise braking on a slippery surface.
Notes
For immediate maximum accelera
tion without touching the gear lever,
press the accelerator pedal down as
far as it will go (kickdown). The gear
box will automatically change down
or maintain the gear selected until
maximum engine speed is reached.
When braking, the gearbox will auto
matically change down in order to
provide efficient engine braking. If you take your foot off the accelera
tor suddenly, the gearbox will not
change to a higher gear for reasons
of safety.
Snow programme
In addition to the autoadaptive pro
gramme, there is a special pro
gramme.
The programme is displayed on the
instrument panel screen.
The Snow programme improves
starting and drive when traction is
poor. 
Press button

once the vehicle
has been started and function D
selected.
The gearbox adapts to driving on
slippery roads.
Note: you can return to the auto
adaptive programme at any time.  Press button

again to switch
off the programme you are in.
Manual operation
Manual changing of the four gears:
 select function M in the gate,
 push the lever to the + sign to
change to a higher gear, 
pull the lever to the – sign to
change to a lower gear.
You can change from position D (dri
ving in automatic mode) to position
M (driving in manual mode) at any
time.
Note
It is only possible to change from one
gear to another if the vehicle speed
and engine speed permit. If they do
not, the vehicle will operate tem
porarily in automatic mode.
When the vehicle is stationary or
moving very slowly, the gearbox
automatically selects gear M1.
The

(snow) programme does not
operate in manual mode.
Operating abnormality
Any operating abnormality is indicated
by an audible signal, accompanied by
the message "Automatic gearbox
faulty" on the multifunction display
and flashing of the Snow warning
light on the instrument panel.
In this situation the gearbox operates
in downgrade mode (locked in 3rd
gear). You may feel a substantial
knock when changing from Pto R
and from N to R (this will not cause
any damage to the gearbox).
Do not exceed 60 mph (100 km/h),
keeping within the limit of local
speed restrictions.
Contact a PEUGEOT dealer as soon
as possible.
18-11-2002

YOUR 807 IN DETAIL135
Disarming the passenger
air bag*
To ensure the safety of your child,
it is essential to disarm the pas
senger air bag when you install a
rearfacing child seat on the front
passenger seat. 
With the ignition switched off,
insert the key into the passenger
air bag disarming switch 1, turn it
to the "OFF" position, then
remove the key keeping the slot
in this position.
The air bag warning light on the
instrument panel is lit throughout the
disarming process. In the
"OFF" position, the passenger
air bag will not be triggered in the
event of an impact.
As soon as the child seat is
removed, turn the air bag slot to the
"ON" position to reactivate the air
bag and thus ensure the safety of
your passenger in the event of an
impact.
Operating check
This is confirmed by an indicator
light, accompanied by an audible
signal and a message on the multi
function display.
With the ignition on (2nd
notch), illumination of this
warning light accompanied
by an audible signal and the
message "Passenger air
bag disarmed" on the
multifunction display, indicates that
the passenger air bag is disarmed
(switch in the "OFF" position). SIDE AIR BAGS AND
CURTAIN AIR BAGS
The side air bags are incorporated
into the front seat backs on the door
side.
The curtain air bags are incorporated
into the door pillars and the upper
part of the passenger compartment.
They are deployed independently of
each other depending on which side
the collision occurs.
Operating check
This is confirmed by an indi
cator light, accompanied by
an audible signal and a
message on the multi–func
tion display.
If this indicator light comes on,
accompanied by an audible signal
and the message "Air bag fault" on
the multi–function display, contact a
PEUGEOT dealer to have the sys
tem checked.
* According to destination. If
the two "Air bag fault" and "Passenger air bag disarmed" warning
lights come on permanently, do not install a rearward facing child seat
and consult a PEUGEOT dealer.
18-11-2002

YOUR 807 IN DETAIL135
Disarming the passenger
air bag*
To ensure the safety of your child,
it is essential to disarm the pas
senger air bag when you install a
rearfacing child seat on the front
passenger seat. 
With the ignition switched off,
insert the key into the passenger
air bag disarming switch 1, turn it
to the "OFF" position, then
remove the key keeping the slot
in this position.
The air bag warning light on the
instrument panel is lit throughout the
disarming process. In the
"OFF" position, the passenger
air bag will not be triggered in the
event of an impact.
As soon as the child seat is
removed, turn the air bag slot to the
"ON" position to reactivate the air
bag and thus ensure the safety of
your passenger in the event of an
impact.
Operating check
This is confirmed by an indicator
light, accompanied by an audible
signal and a message on the multi
function display.
With the ignition on (2nd
notch), illumination of this
warning light accompanied
by an audible signal and the
message "Passenger air
bag disarmed" on the
multifunction display, indicates that
the passenger air bag is disarmed
(switch in the "OFF" position). SIDE AIR BAGS AND
CURTAIN AIR BAGS
The side air bags are incorporated
into the front seat backs on the door
side.
The curtain air bags are incorporated
into the door pillars and the upper
part of the passenger compartment.
They are deployed independently of
each other depending on which side
the collision occurs.
Operating check
This is confirmed by an indi
cator light, accompanied by
an audible signal and a
message on the multi–func
tion display.
If this indicator light comes on,
accompanied by an audible signal
and the message "Air bag fault" on
the multi–function display, contact a
PEUGEOT dealer to have the sys
tem checked.
* According to destination. If
the two "Air bag fault" and "Passenger air bag disarmed" warning
lights come on permanently, do not install a rearward facing child seat
and consult a PEUGEOT dealer.
18-11-2002