PEUGEOT 807 2004 Workshop Manual

54
26-04-2004
55
26-04-2004
YOUR 807 IN DETAIL
The directory
General
The "Directory" application gives
access to 400 iles divided into 4 in-
dependent sub-directories ("User1",
"User2", "User3" and "User4"). It
enables you to manage these iles,
make calls using the SIM card and
activate guidance.
From the general menu , select the
"Directory" application to access its
main menu and select one of the fol-
lowing functions:
• "Call", to call a number stored in a ile,
• "Activate guidance to", to initiate guidance to a location stored in a
ile,
• "Management of directory iles", to add, delete, modify and consult di-
rectory iles or exchange them with
the SIM card,
• "Directory coniguration", to select the working directory and deine
the directory when the system is
switched on.
Main menu
To create a ile, from the
"Directory"
menu, select the "Management of di-
rectory iles" function, then "Add".
In the ile, select the section to be
illed in, conirm and then enter the
information.
To modify an existing ile, select it by
means of the "Consult or modify the
ile" function of the "Management of
directory iles" menu, then make the
modiications.
Note: when entering the address,
the navigation CD ROM must be
present to obtain guidance to this
destination.
Creation / Modiication of a ile Description of a directory
ile
When a description is associated
with a directory ile, you can record
the description vocally to use it later
for direct access by means of voice
commands (e.g.: "Call" "[Name of
voice description]" or "Guide to"
"[Name of voice description]" ).
Select "Consult or modify the ile"
from the "Management of directory
iles" menu to access the description
entering and recording screen.
Press the record button and follow
the instructions.
TMC (Traffic Message Channel)
RDS Traffic Information
You can access the information
regarding the status of the trafic
on the road from the "Audio func-
tions" or "Telematics" menu, then
the "Trafic Information TMC" func-
tion (see section "Satellite navigation
system").

56
26-04-2004
YOUR 807 IN DETAIL
VOICE COMMANDS
The voice commands make it pos-
sible to use pre-recorded words or
phrases to control a certain number
of functions of the RT3 GPS audio/
telephone.
Activation of the voice commands
Press the button on the end of the
lights stalk to activate or deacitvate
this function.
Example: to recall the radio station
stored on button 3, the key words
are: "Radio" "Memory" "3" .
To use these key words, you must
say the word "Radio", wait for the
audible conirmation signal, then
say the word "Memory", wait for the
audible conirmation signal, then end
with the word "3", wait for the audible
conirmation signal which will carry
out the action requested.
Notes:
- between two key words, a screen indicates the time remaining and
the key word recognised,
- in the absence of any voice commands, this function will be
switched off after approximately
ive seconds,
- if a command is not understood, the system transmits the phrase
"Pardon" and displays "Word not
recognised" on the screen. Saying the phrase
"Help" or "What
can I say" displays all of the com-
mands available on the screen.
List of commands available
- For the radio, say "RADIO", then:
"PREVIOUS" / "FOLLOWING" / "MEMORY" + "1...6" / "AUTO-
STORE" / "LIST"
- For the CD, say "CD PLAYER", then:
"PREVIOUS TRACK" / "FOLLOWING TRACK" / "TRACK
NUMBER" + "1...20" / "SHUFFLE" /
"SCAN" / "LIST"
- for the CD changer, say "CHANG- ER", then":
"PREVIOUS TRACK" / "FOLLOWING TRACK" / "TRACK
NUMBER" + "1...20" / "PREVIOUS
DISC" / "FOLLOWING DISC" /
"DISC NUMBER" + "1...6" / "SHUFFLE" / "SCAN" / "REPEAT" /
"LIST"
- For the telephone, say "TELE- PHONE", then:
"LAST NUMBER" / "DIREC- TORY" + DESCRIPTION / "SERV-
ICES" / "VOICE MAIL" / "VOICE
MESSAGES"
- For the text messages, say "SMS" or "MESSAGE", then:
"DISPLAY" / "READ"
- For the RDS trafic information TMC, say "TRAFFIC-INFO", then:
"DISPLAY" / "READ" - For navigation/guidance, say
"NAVIGATION" or "GUIDANCE",
then:
"STOP" / "RE-START" / "DIRECTORY" + DESCRIPTION /
"ZOOM PLUS" / "ZOOM MINUS" /
"SHOW" + "DESTINATION" /
"SHOW" + "VEHICLE"
- To change the permanent applica- tion, say "DISPLAY", then:
"AUDIO" / "TELEPHONE" / "NAVI- GATION" / "GUIDANCE" / "TRIP
COMPUTER"
- To call someone recorded in the directory directly, say "CALL" +
DESCRIPTION
- To be guided to the address of someone recorded in the directory,
say "GUIDE TO" + DESCRIPTION
- Various:
"CANCEL" / "HELP" / "WHAT CAN I SAY" / "STOP" / "DELETE" /
"YES" / "NO" / "PREVIOUS" /
"NEXT"

57
26-04-2004
YOUR 807 IN DETAIL
To insert a disc into the changer:
- open sliding panel A,
- press button B to eject the car-
tridge C,
- open one of the six compartments of the cartridge by pulling tab D,
- insert the disc with the printed
face upwards and close the
compartment,
- insert the cartridge into the changer,
- close the sliding panel A.
This is located inside the passen-
ger's lower glove compartment. It
holds up to 6 discs.
CD CHANGER
The use of copied com-
pact discs may cause
faults.
Insert circular compact
discs only.

58
26-04-2004
59
26-04-2004
YOUR 807 IN DETAIL
SATELLITE NAVIGATION
SYSTEM
Introduction
The satellite navigation system
guides you, by means of vocal and
visual instructions (graphics), to
your chosen destination.
The heart of the system lies in the
use of a map data base and
GPS
(Global Positioning System) . With
this system you can ix the position
of your vehicle by means of a satel-
lite network.
The system uses the following ele-
ments:
- the CD-Rom drive,
- the coniguration CD-Rom,
- the navigation CD-Rom,
- the last voice message recall control,
- the control keypads,
- the CT monochrome display or the DT colour screen.
Certain functions or services de-
scribed may vary depending on
the version of the CD-Rom or the
country where the vehicle is sold.
For safety reasons, the
inputting of navigation
information by the driver
must be carried out when
the vehicle is stationary.
The CD-Rom drive
This is part of the RT3 GPS audio/
telephone.
1. CD-Rom ejection button.
2. CD-Rom housing.
The navigation CD-Rom
This contains all the map data.
It must be inserted in the drive, printed
face upwards.
Use only CD-Roms approved by
PEUGEOT. The last voice message recall
control
Pressing for more than two seconds
on the button at the end of the lights
stalk repeats the last voice informa-
tion.

58
26-04-2004
59
26-04-2004
YOUR 807 IN DETAIL
RT3 GPS audio/telephone control
keypad
The control keypads
These let you select and validate
the functions, commands and pro-
grammes displayed.
The additional telematics control is
located by the side of the gear lever.
or additional telematics controlRotation of the dial:
This allows you to
move round the
screen and thus select a function.
It also allows you:
- with a 'setting' type parameter,
after selection, to increase or de-
crease the value,
- with a 'list' type parameter, after
opening the list, to scroll through
the values,
- with map guidance, to increase or
decrease the zoom.
Pressing the dial:
This allows:
- access to the list of controls (con-
textual menu) of the permanent
display, if there is no other display
superimposed.
- conirmation of the selected func-
tion or the modiied value.
- selection of a 'setting' or 'list'
type parameter for modiication.
"MODE" button
- Brief press: modiication of per- manent display (audio system,
navigation/guidance...),
- Pressing for more than two seconds displays general information .'ESC' button:
- Brief press:
cancelling of opera-
tion in progress or erasing of last
superimposed display.
- Pressing for more than two seconds: erasing of all superimposed displays
and return to the permanent display.
'MENU' button:
- Brief press: access to the general
menu .
- Pressing for more than two seconds: access to the help menu.
"NAV" button
- Brief press: display of the con- textual menu of the navigation/
guidance function.
"MAIN" button
- Brief press: display of the general
information .
Tip:
You can access the general menu
by pressing:
- the dial G of the RT3 GPS audio/
telephone ,
or
- the dial of the additional telematics control.

60
26-04-2004
61
26-04-2004
General menu
Switch on the RT3 GPS audio/
telephone and insert the navigation
CD-Rom.
Press the "MENU" button to access
the general menu .
During guidance, if the navigation
CD-Rom is present, the screen dis-
plays different information depend-
ing on the manoeuvres to be carried
out.
1.
Current manoeuvre or compass or
course (if calculation in progress
or zone not mapped).
2. Next manoeuvre to be carried
out.
3. Next road to be taken.
4. Current road.
5. Estimated time of arrival at
destination.
6. Distance to inal destination.
7. Distance to next manoeuvre.
Notes:
- depending on the situation of the vehicle and on the reception of
GPS information, this information
may disappear from the screen
temporarily,
- during guidance, the navigation CD ROM must remain in the RT3 GPS
audio/telephone.
General notes on the display
YOUR 807 IN DETAIL
Monochrome screen CT
Colour screen DT
Select the Navigation/Guidance icon
using the dial G, then validate by
pressing the dial to access the main
"Navigation - Guidance" menu.
7654
7654
123
321

60
26-04-2004
61
26-04-2004
YOUR 807 IN DETAIL
The main "Navigation - Guidance"
menu offers various options for acti-
vation or management of guidance:
- choice of the type of destination address (entering of address,
service, GPS co-ordinates, stored
address),
- modiication to the initial route (en- tering of a diversion),
- displaying of the chosen destination,
- setting of the guidance option pa- rameters,
- stop or resume guidance (display- ing of the message which changes
depending on the previous status).
Navigation - Guidance
The "Destination choice" menu
offers various options for reaching a
destination:
• ฀ entering a postal address,
• ฀ selecting a service available in
a town (town hall, hotel, cinema,
airport...),
• ฀ entering GPS details,
• ฀ selecting a destination stored in the
directory,
• ฀ selecting one of the previous desti-
nations.
Selecting a destination
The last guidance address is dis-
played.
Select and validate in succession the
entry zones "Town", "Road" , then
"N°" to ill them in.
The "OK" function permits valida-
tion of the address and access to the
guidance activation function.
The "Store" function permits record-
ing of the address in a directory ile.
The "Curr. loc." function permits dis-
play of the current address.
Entering an address

62
26-04-2004
63
26-04-2004
YOUR 807 IN DETAIL
To enter the name of a town, select
each letter by turning the dial, then
validate each letter by pressing the
dial.
If an error is made entering the let-
ters, the "Change" function permits
erasing of the last letter entered.
Note: following the validation of a
letter, only those which could make
up a name existing in the database
appear.
As letters are entered, the "List" func-
tion indicates the number of towns
beginning with the same letters. Acti-
vation of this function permits selection
of a town from the list.
Entering the name of the town
When the list contains fewer than ive
names, these are displayed automat-
ically. Select a town then validate by
pressing the dial.
When the complete name of the town
is displayed, select the "OK" function
then conirm by pressing the dial.
Note: once the town has been en-
tered, you can conirm by pressing
"OK" . You will then be guided to the
centre of this town automatically.
Entering the name of the road
Enter the name of the street in the
same way as the name of the town.
When the full name of the street is
displayed, select the "OK" function
then conirm by pressing the dial.
Entering the town and road using
the alphanumeric keypad
Press the numeric key which corre-
sponds to the letter required until the
letter appears on the screen, then
conirm by pressing the # key after
each letter. Enter the number of the street previ-
ously entered.
Select the
"OK" function, then con-
irm by pressing the dial.
Note: if the number of the street en-
tered is not available, it is rejected.
You can also select a street from the
"Junctions" function, which avoids
having to enter the street number.
Note: if the street selected does not
have a number, the list of junctions is
displayed automatically.
The full destination is displayed.
Select the "OK" function, then
conirm by pressing the dial to
access the guidance activation
function. Follow the instructions
given by the system.
Entering the number of the road
or junction

62
26-04-2004
63
26-04-2004
YOUR 807 IN DETAIL
The last address entered is dis-
played.
There are three options for deining
the location in which you wish to
obtain this service:
- accept the last address entered using the "OK" function,
- ill in the "Town" and "Road"
zones,
- automatically enter the name of your current location using the
"Curr. loc." function.
Selecting a service
If you wish to be directed to a service,
select the
category corresponding to
the service, then conirm by pressing
the dial.
The list of services corresponding to
the category selected is displayed.
Select the service then conirm
by pressing the dial to access the
"Choice of a location" function.
An indication on the edge of the
screen (x/n) shows you the maximum
number of establishments providing
the same service within a radius of
30 miles (50 km), as the crow lies,
from the selected location.
Use buttons &#34;<&#34; and &#34;>&#34; to consult
the list provided.
When the establishment of your
choice is displayed, you can:
• ฀ select the &#34;OK&#34; function to activate
guidance towards this service,
• ฀ select the &#34;Store&#34; function to enter
this establishment in your directory.
Note:
if the service selected is not
available in the programmed loca-
tion, a temporary message informs
you of this.
Following validation of the location,
the service closest to it is displayed.
The distance indicated is the distance
as the crow lies from the service to
the selected location.
The most recent destinations are
shown.
There are three possible methods
of deining the location to which you
wish to travel:
- accept the last details input by means of the &#34;OK&#34; function,
- input the details of your destination,
- automatically input the details of your current location by means of
the &#34;Curr. loc.&#34; function.
GPS details

64
26-04-2004
65
26-04-2004
YOUR 807 IN DETAIL
Select the &#39;&#39;Directory&#39;&#39; function to
access the ile in which the address
you are looking for is archived.
Select a description by scrolling
down the list by means of the dial,
then conirm by pressing the dial.
The directory ile is then displayed.
Select the &#34;OK&#34; function, then press
the dial to access the guidance acti-
vation function.
Follow the directions given by the
system.
Selecting a destination stored in
the directory
Select the &#34;Previous destinations&#34;
function to access one of the last
twenty addresses stored.
Select a description by scrolling
down the list by means of the dial,
then conirm it by pressing the
dial. The complete address is then
displayed.
Select the &#34;OK&#34; function, then press
the dial to access the guidance
activation function.
Follow the instructions given by
the system.
Selection of one of the previous
destinations
Activate the function &#39;&#39;Divert route&#39;&#39;,
then input the distance involved in
the change required.
Select the &#39;&#39;OK&#39;&#39; function then vali-
date by pressing the dial.
The system calculates the change
which is closest to the value input
and gives you the option of whether
or not to use this change.
Details of the route
You can consult the destination ad-
dress at any time by activating the
&#34;Chosen destination&#34; function on
the &#34;Navigation - Guidance&#34; menu.
Changing the initial route