PEUGEOT 807 2007.5 Owners Manual

161
Battery
TROUBLESHOOTING
8
ECONOMY MODE FUNCTION
After the engine has stopped, with the key
in the ignition position, certain functions
(windscreen wiper, electric windows, courtesy
lights, audio equipment, etc.) can only be
used for a cumulative duration of thirty
minutes, to prevent discharging the battery.
Once the thirty minutes are over, the
message
"Economy mode active" appears
on the display and the active functions are
put on standby.
To resume the use of these functions
immediately, start the engine and let it run
for a few seconds.
A flat battery will prevent the engine from
starting.
This is housed in a compartment located
underneath the floor, in front of the driver ’s
seat.

To charge the battery using a battery
charger  Disconnect the battery,
 Follow the instructions for use given by
the battery charger manufacturer,
 Reconnect starting with the negative (-)
terminal,
 Check that the terminals and connectors
are clean. If they are covered with
sulphate (white or greenish deposit),
disconnect them and clean them.
To start the vehicle from another battery  Connect the red cable to the positive (+)
terminals of the two batteries,
 Connect one end of the green or black
cable to the negative (-) terminal of the
slave battery,
 Connect the other end of the green or
black cable to an earth point on the
broken down vehicle as far as possible
from the battery,
 Operate the starter, let the engine run,
 Wait for the engine to return to idle, then
disconnect the cables.
BATTERY
Before disconnecting the battery, you must
wait for 2 minutes after switching off the
ignition.
Never disconnect a terminal when the
engine is running.
Never charge a battery without first
disconnecting the terminals.
Close the sunroof and the windows before
disconnecting the battery. If they do not
operate normally following reconnection of
the battery, they must be reinitialised.
Refer to the "Accesses" section of chapter 2
for the sunroof safety auto-reverse and to the
"Mirrors and windows" section of chapter 3 for
the electric windows safety auto-reverse.
It is advisable to disconnect the battery
if the vehicle is not to be used for a
period of more than one month.
After every reconnection of the battery,
switch on the ignition and wait 1 minute
before starting to allow the electronic
systems to be initialised. If slight difficulties
are experienced after this, please contact a
PEUGEOT dealer.
The door open monitoring electrical system
consumes power, remember to close the
sliding doors when your vehicle is parked
for long periods.

Changing a wheel
162
CHANGING A WHEEL
1. PARKING THE VEHICLE
- If possible, park the vehicle on level, stable and non-slippery ground.
- Apply the handbrake, switch off the ignition and engage first or reverse gear (position P
for the automatic gearbox) .
- If possible, place a chock under the wheel diagonally opposite the one to be changed. 1 -
Wheelbrace.
2 - Jack housing.
3 - Alloy wheel embellisher remover.
4 - Removable towing eye.
Refer to the location of the tools
(situated in the engine compartment) in
the "Under the bonnet" section of chapter 7.
2. TOOLS 3. SPARE WHEEL 
Gain access to the spare wheel from the
boot.
 Open the cover to release the winch and
access its bolt.You can switch on the row 3 courtesy
light to increase the light in the boot.

163
Changing a wheel
TROUBLESHOOTING
8
 Unwind the winch cable by unscrewing
the bolt using the wheelbrace.
 Detach the spare wheel from the rear of
the vehicle and place it near the wheel to
be changed. 4. OPERATING PROCEDURE
Special tools for vehicles fitted with alloy
wheels
If your vehicle has wheels with alloy rims:  The embellisher is removed using the
alloy wheel embellisher remover.
 Each wheel is fitted with an anti-theft bolt.
These bolts can be loosened using your anti-theft socket (given to you on
delivery of your vehicle along with your
confidential card) and the wheelbrace.

Remove the trim pulling at the valve
passage hole. Use the flat end of the
towing eye as a lever.
 Loosen the wheel bolts and start
unscrewing them.

Changing a wheel
164
Do not extend the jack until you have
started unscrewing the bolts on the
wheel to be changed and have placed the
chock under the wheel diagonally opposite.
 Place the jack in contact with the locating
point provided, the one which is closest
to the wheel to be changed. Ensure that
the base of the jack is in contact with the
ground, and straight above.
 Extend the jack to lift the wheel clear of
the ground. 
Resume and complete the unscrewing of
the wheel bolts.
 Remove the bolts and remove the wheel. 5. FITTING THE SPARE WHEEL 
Position the wheel on the hub and start
tightening the bolts by hand.
 Initially tighten the bolts using the
wheelbrace.

165
Changing a wheel
TROUBLESHOOTING
8
 Lower the vehicle completely by folding
the jack, then remove the jack.
 Tighten the bolts again using the wheelbrace,
tighten them fully without forcing them. 
Place the wheel to be repaired in the boot
well by raising the winch cable using the
wheelbrace.
 Remember to close the flap, located in
the boot, it permits securing of the winch.
 Store the trim in the boot.
Never go underneath a vehicle that
is supported only by a jack (use a
ramp). Never use a screwdriver in place of
the wheelbrace to unwind or wind the winch
cable.
6. REFITTING THE REPAIRED
WHEEL
The wheel is refitted as described in step 5,
not forgetting to refit the wheel trim.
The spare wheel is not designed to be
used over long distances,
Have the tightening of the bolts and the tyre
pressure checked by a PEUGEOT dealer as
soon as possible.
Also, have the original wheel repaired and
refitted by a PEUGEOT dealer as soon as
possible.

Changing a bulb
166
CHANGING A BULB
FRONT LIGHTS
1 - Dipped headlamps
2 - Main beam headlamps
3 - Fog lamps
4 - Side lights
5 - Direction indicators1 - Dipped beam headlamps
H7-55 W or xenon bulb.
2 - Main beam headlamps
H7-55 W or xenon bulb. 3 - Fog lamps

H1-55 W.
WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be changed by a
PEUGEOT dealer.
Handle the bulbs with a dry cloth.
Make access easier on the right-hand
side by removing the wash-wipe pipe and
the fuse box cover.
 Turn the protective cover corresponding
to the faulty bulb a quarter of a turn to the
left and remove it.
 Disconnect the connector.
 Press the end of the securing clip to free
it. Change the bulb.
When fitting the new bulb, ensure that the
direction notches are positioned correctly
and the securing clip is fixed properly. Reconnect the connector.
 Refit the protective cover, then turn it a
quarter of a turn to the right. 4
- Side lights
W 5 W.
 Push the light from the inside towards the
outside of the bumper.
 Pull the light forwards.
 Turn the bulb holder a quarter turn to the
left and remove it.
 Turn the bulb a quarter turn to the left,
remove it and change it.
When refitting, engage the light towards the
outside and move it towards the inside of the
bumper.

167
Changing a bulb
TROUBLESHOOTING
8
REAR LIGHTS
1 - Direction indicators
PY 21 W (amber).
2 - Brake/side lights
P 21/5 W.
3 - Reversing lights
P 21 W.
4 - Fog lamps
P 21 W.
These 4 bulbs are changed from inside the
vehicle: open the tailgate,
 remove the air extraction grille on the side
concerned,
 unclip the light harness,
5 - Direction indicators

PY 21 W (amber).
 Turn the bulb holder a quarter of a turn to
the left and remove it.
 Change the bulb.
The headlamps are fitted with
polycarbonate glass with a protective
coating. Do not clean them with a dry or
abrasive cloth, nor with a detergent or solvent
product. Use a sponge and soapy water.
In certain climatic conditions (low
temperature, humidity), condensation inside
the headlamp glass is normal; it disappears a
few minutes after the lights are switched on.
Direction indicator side repeaters
WY 5 W (amber). Push the repeater rearwards and release
it from the mirror.
 Hold the connector and turn the bulb
holder a quarter turn to the left.
 Turn the bulb a quarter turn to the left,
remove it and change it.
When refitting, engage the repeater towards
the rear and move it towards the front of the
mirror.
Amber coloured bulbs (direction
indicators and side repeaters) must be
changed for bulbs of identical specification
and colour.

167
Changing a bulb
TROUBLESHOOTING
8
REAR LIGHTS
1 - Direction indicators
PY 21 W (amber).
2 - Brake/side lights
P 21/5 W.
3 - Reversing lights
P 21 W.
4 - Fog lamps
P 21 W.
These 4 bulbs are changed from inside the
vehicle: open the tailgate,
 remove the air extraction grille on the side
concerned,
 unclip the light harness,
5 - Direction indicators

PY 21 W (amber).
 Turn the bulb holder a quarter of a turn to
the left and remove it.
 Change the bulb.
The headlamps are fitted with
polycarbonate glass with a protective
coating. Do not clean them with a dry or
abrasive cloth, nor with a detergent or solvent
product. Use a sponge and soapy water.
In certain climatic conditions (low
temperature, humidity), condensation inside
the headlamp glass is normal; it disappears a
few minutes after the lights are switched on.
Direction indicator side repeaters
WY 5 W (amber). Push the repeater rearwards and release
it from the mirror.
 Hold the connector and turn the bulb
holder a quarter turn to the left.
 Turn the bulb a quarter turn to the left,
remove it and change it.
When refitting, engage the repeater towards
the rear and move it towards the front of the
mirror.
Amber coloured bulbs (direction
indicators and side repeaters) must be
changed for bulbs of identical specification
and colour.

Changing a bulb
168
NUMBER PLATE LIGHTS
W 5 W Remove the lens.
 Change the faulty bulb. THIRD BRAKE LIGHT
5 W 5 W bulbs

 Remove the tailgate upper trim by
unclipping it on each side.
 Squeeze the two tabs 1 to release the
bulb holder.
 Change the faulty bulb.
 When refitting, ensure that the tailgate
upper trim has been put back in place
correctly.

unscrew the two interior nuts and remove
the light,
 unscrew the bulb holder concerned an
eighth turn to the left and remove it,
 unscrew the faulty bulb an eighth turn to
the left and change it.
When refitting: take care to position the bulb correctly and
press on it to engage it,
 take care to position the bulb holder
correctly and screw it in an eighth of a
turn to the right,
 take care to position and secure the light
correctly.
When two or more bulbs are faulty, you
must replace them immediately.

169
Changing a fuse
TROUBLESHOOTING
8
CHANGING A FUSE
The fuse boxes are located in:
- the instrument panel lower glove box (right-
hand side),
- the battery compartment (right-hand side floor),
- the engine compartment.
The spare fuses and special pliers A are
fixed to the inside of the lid of the instrument
panel fuse box. Removing and changing a fuse
Before changing a fuse you must establish
the cause of the fault and have it corrected.
The fuse numbers are indicated on the fuse
box. 
Use the special pliers A.
Always change a faulty fuse for one of
the same rating.