PEUGEOT 807 2007.5 Repair Manual

Seats
ERGONOMICS and COMFORT63
3
Control for sliding the rear side seats
from row 3 or the boot
Pull the strap (marked with the arrow
symbol) to slide the seat in front of you.Removing the side seat
1 -
Tilt the seat back forwards to detach the
rear anchorages.
2 - Grab the red strap which appears and
pull it upwards, the front anchorages
unlock.
Refitting the side seat 3 -
The strap, like the handle, enables you
to remove the seat.
1 - Place the front anchorages at the front
stop in the slides. Support the strap
firmly for easier positioning of the seat.
2 - Tilt the folded seat towards the rear.
The rear anchorages lock.
3 - Raise the seat back.
4 - Slide the seat.
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat anchorages.

Seats
64
ROW 2 CENTRE SEAT
This can be placed in row 3, on the left."Low table" position
1 -
Place the head restraint in the low
position.
2 - At the top (at the back of the seat), lift
the handle identified by the symbol
and guide the tilting of the seat back
towards its seat cushion. 3 -
You have a "low table". To return to the
seat position, lift the handle and guide
the raising of the seat back.
Removing the centre seat
1 - Place the seat in the "low table"
position.
2 - Using the control which you pull, tilt the
seat back forwards so releasing the rear
anchorages from the slides. 3 -
Grab the red strap which appears and
pull it upwards, the front anchorages
unlock.
4 - The strap, like the handle, enables you
to remove the seat.

Seats
ERGONOMICS and COMFORT65
3
Rear head restraints
The rear head restraints can be removed
and have two positions:
high, position for use,
 low, storage position.
To raise or lower a head restraint, pull it
forwards sliding it at the same time.
To remove it, place it in the high position,
push the lug and pull it forwards and
upwards.
To refit it, engage the head restraint rods in
the holes taking care to remain in the
centreline of the seat back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.
Refitting the centre seat
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat anchorages.
1 - Place the front anchorages at the front
stop in the slides. Support the strap
firmly for easier positioning of the seat.
2 - Tilt the folded seat towards the rear.
The rear anchorages lock.
3 - Raise the seat back and slide the seat.
Turning a rear seat round

The rear seats can be placed in a "face to
face" position.
Carry out the operations described for
removal then turn the seat round and resume
with the procedure for refitting the seat.
This turning operation must be carried out
when stationary.
Driving with a passenger seated facing
the rear is prohibited.
When the vehicle is being driven, placing
a row 2 seat in the closed position while a
passenger is sitting in row 3 is prohibited.

Seats
ERGONOMICS and COMFORT65
3
Rear head restraints
The rear head restraints can be removed
and have two positions:
high, position for use,
 low, storage position.
To raise or lower a head restraint, pull it
forwards sliding it at the same time.
To remove it, place it in the high position,
push the lug and pull it forwards and
upwards.
To refit it, engage the head restraint rods in
the holes taking care to remain in the
centreline of the seat back.
Never drive with the head restraints
removed, they must be in place and
correctly adjusted.
Refitting the centre seat
Check that there is no obstacle
obstructing the slides or preventing
correct locking of the seat anchorages.
1 - Place the front anchorages at the front
stop in the slides. Support the strap
firmly for easier positioning of the seat.
2 - Tilt the folded seat towards the rear.
The rear anchorages lock.
3 - Raise the seat back and slide the seat.
Turning a rear seat round

The rear seats can be placed in a "face to
face" position.
Carry out the operations described for
removal then turn the seat round and resume
with the procedure for refitting the seat.
This turning operation must be carried out
when stationary.
Driving with a passenger seated facing
the rear is prohibited.
When the vehicle is being driven, placing
a row 2 seat in the closed position while a
passenger is sitting in row 3 is prohibited.

Seats
66
REAR BENCH SEAT
Forwards/backwards adjustment
From the seat cushion, lift bar A and slide
the seat towards the front or the rear.
From the boot, you can pull on strap B
and slide the seat forwards to make it
easier to load the vehicle.
The rear bench seat must only be fitted
in row 3.
Seat back folded position
1 - Place the head restraints in the low
position.
2 - Pull the strap C upwards, from the
tailgate. 3 -
Tilt the seat back on the seat cushion.
Vertical position of the bench seat
1 - Place the head restraints in the low
position.
2 - Pull the strap C upwards, from the
tailgate.
3 - Fold the seat back onto the seat
cushion. 4 -
Pull the lever D to unlock the rear
anchorages.
5 - Place the seat in the vertical "folded"
position.
When driving, attach the retaining
straps to the handles.

Seats
ERGONOMICS and COMFORT67
3
Removing the bench seat
1 -
Fold the seat to the vertical position.
2 - Grasp the two bars E underneath the
seat. 3 -
The front
anchorages unlock.
Refitting the bench seat
For removal and refitting, pass the rear
seat, in the "folded" position, through
the sliding side doors.
Check that there is nothing blocking
the runners which could prevent correct
locking of the bench seat anchorages.
1 - Position the front anchorages at the
front stop of the runners.
2 - Tilt the folded seat rearwards.
3 - The rear anchorages then lock.
4 - Unlock the seat back and lift it using the
strap C.
Good practice
When the vehicle is being driven, it is
prohibited for a passenger to sit:
- in the 3rd row if the seat back in front (2nd row) is in the table position.
- in the 3rd row if the seat/bench in front (2nd row) is in the vertical folded position.
- in the centre seat if the right-hand side seat is in the vertical folded position.

Seats
68
The centre seat may be installed in the
central position in row 2 and in the left
side position in row 3.
MODULARITY AND POSSIBLE SEAT CONFIGURATIONS
Examples of various arrangements
combining pleasure and practicality:
The various operations modifying the
existing configuration must be carried
out with the engine switched off (See section
on "Seats").
It is prohibited to be in a rearwards facing
position when the vehicle is being driven.
The rotating of the seats depends on the
vehicle equipment and the country.
5 seats with picnic position when parked 5 seat arrangements

Seats
ERGONOMICS and COMFORT69
3
7 seats with access to row 3
8 seats with bench seat

Seats
70
"Cargo"/transportation of long objects configuration6 seats "Pullman"

Practical information
ERGONOMICS and COMFORT71
3
FRONT SEAT LAYOUT
Storage drawers
There is a storage drawer under each front seat.
- To open it, lift and pull.
- To take it out, open it to its full extent, lift
the two tabs on either side of the drawer,
then remove it completely.
Each front seat also has a storage
pocket on the seat back.
12 V socket
You have a 12 V accessory socket at the
foot of the driver ’s seat, which is accessible
to passengers of row 2.
Front and rear armrests
To place the armrest in its rest position:
- Lift the armrest until it is aligned with the
seat back.
To place the armrest in the position
in which it is used:
- Push it towards the rear,
- Fold it down completely,
- Raise it slowly to the required position,
- If you lift it past the required position, restart the above operations.
Elastic retaining straps
There is an elastic retaining strap on each
front seat, on the centre side.
- In the side position (elastic strap on its
own seat), this can be used as a magazine
holder.
- In the transverse position (elastic straps A hooked between the two seats), they can
hold a bag.
"Aircraft" type table
You have an "aircraft" type table with a rim,
equipped with a cup holder, fitted to the rear
of each front seat.
Do not forget to fold this before pivoting
the seat.
PRACTICAL INFORMATION
Under the front seat on the passenger
side, if the vehicle has an amplifier, the
storage drawer will be locked.