steering PEUGEOT 807 2008 User Guide

Page 44 of 194

Steering wheel controls
ERGONOMICS and COMFORT
3
47
WINDSCREEN WIPER STALK
Manual windscreen wipers Special position of the
windscreen wipers
In the minute following switching
off of the ignition, any action on the
stalk positions the wipers against the
windscreen uprights.
This action enables you to position
the wiper blades for winter parking,
cleaning or replacement. Vehicle fitted with the
automatic windscreen
wipers control
Do not cover the rain sensor located in
the centre of the fascia.
On vehicles which are itted with
this control, in the AUTO position,
the windscreen wipers operate
automatically and adapt their speed
to the intensity of the rainfall .
When not in AUTO mode, for the
other positions, refer to the manual
windscreen wipers section.
The command must be reactivated
whenever the ignition has been
switched off for more than one
minute: 4
move the stalk to any position,
4 then move it back to the required
position.
2
Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
l Intermittent wipe.
0 Off.
â Single wipe
(press downwards). Refer to the "Changing a
windscreen wiper blade" section of
chapter 8.
Wash-wipe and headlamp wash
Pull the stalk towards you, the wash-
wipe is accompanied by a timed sweep
of the wipers.
If your vehicle is itted with this
function, the headlamp wash is linked
with the wash-wipe, it is triggered if the
dipped headlamps are on. To park the wipers in their normal
position after this has been done, switch
on the ignition and move the stalk.
To top up the levels, refer to the
"Levels" section of chapter 7.
In the Intermittent position, the wiping
speed is in proportion to the vehicle
speed.

Page 45 of 194

Steering wheel controls
48
Activation
Press the control downwards.
Activation of the function is
accompanied by a message on the
display.
The automatic windscreen wipers
function must be reactivated if the
ignition has been switched off for more
than one minute, by pressing the stalk
downwards.
Rear windscreen wiper
Turn the ring to the irst
notch. The wiping speed is
inversely proportional to the
speed of the vehicle.
Rear windscreen wash
Turn the ring past the irst
notch: the windscreen wash
then the windscreen wiper
operate for a ixed time. Good practice
When using an automatic car
wash, switch off the ignition without
setting the alarm.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic wiping.
In the event of a considerable amount
of snow or ice, switch on the rear
screen demister. Once de-icing is
complete, remove the snow or ice
which has accumulated on the rear
wiper blade. You can now operate the
rear windscreen wiper.
If a tailgate bicycle carrier
is used, deactivate the rear
wiper by going to the display’s
coniguration menu.
Deactivation/Switching off
Place the windscreen wipers stalk in
position
I, 1 or 2. Deactivation of the
function is accompanied by a message
on the display.
In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in
intermittent mode.
Contact a PEUGEOT dealer to have
the system checked. Automatic wiping - reverse gear
- place the front wipers stalk in a
position other than 0.
- engage reverse gear.
- the rear wiper operates with intermittent wiping.

Page 46 of 194

Steering wheel controls
ERGONOMICS and COMFORT
3
49
CRUISE CONTROL "CRUISE"
"This is the speed at which the driver
wishes to drive".
This aid to driving in free-lowing
trafic enables the vehicle to maintain
the speed programmed by the driver,
unless a steep gradient makes this
impossible.
In order for it to be programmed or
activated, the vehicle speed must be
greater than 25 mph (40 km/h) with at
least 4th gear engaged in the case of
vehicles itted with a manual gearbox.On vehicles itted with an automatic
gearbox, the lever must be in position
D
(Drive) or at least 2nd gear must be
engaged in manual mode.
If the vehicle is itted with a speed
limiter and cruise control (according
to the country in which the vehicle is
sold and the engine), these functions
cannot be activated at the same time. Function selected,
displaying of the
"Cruise Control"
symbol.
Function deactivated,
OFF (example at
65 mph (107 km/h)).
Function activated
(example at 65 mph
(107 km/h)).
Vehicle speed above
(e.g. 70 mph

(118 km/h)),
the programmed
speed is displayed
lashing.
Operating fault
detected,
OFF - the dashes
lash.
This cruise control shows the function
selection status on the instrument
panel and displays the programmed
speed:

Page 47 of 194

Steering wheel controls
50
Selecting the function
- Place the switch in the CRUISE
position. The cruise control is
selected but is not yet active and
no speed has been programmed.
First activation/
programming a
speed
- Reach the chosen speed by pressing
the accelerator.
- Press the SET - or
SET + button.
This programmes/activates the
reference speed and the vehicle will
maintain this speed. Temporary exceeding of the
speed
It is possible
to accelerate and drive
momentarily at a speed greater than
the programmed speed. The value
programmed lashes.
When the accelerator pedal is
released, the vehicle will return to the
programmed speed. Reactivation -
Following deactivation of the cruise
control, press this button.
Your vehicle will return to the last
programmed speed.
Alternatively, you can repeat the "irst
activation" procedure.
Deactivation (off)
- Press this button or the brake or clutch
pedal.

Page 48 of 194

Steering wheel controls
ERGONOMICS and COMFORT
3
51
Switching the function off - Place the dial in position 0 or switch
off the ignition to switch everything
off. Good practice
When changing the programmed
reference speed by means of a
maintained press, pay attention as
the speed can increase or decrease
rapidly.
Do not use the cruise control on
slippery roads or in heavy trafic.
In the event of a steep slope, the cruise
control cannot prevent the vehicle from
exceeding the programmed speed.
In any event, the cruise control cannot
replace the need to observe the speed
limits, nor can it replace the need for
vigilance and responsibility on the part
of the driver.
To avoid any jamming under the
pedals:
- ensure that the mat is positioned correctly,
- never place one mat on top of another
Changing the
programmed speed
There are two methods of
memorising a speed higher
than the previous one:
Without using the
accelerator:
- press the Set + button.
A brief press increases the speed by
1 mph (km/h).
A maintained press increases the
speed in steps of 5 mph (km/h).
Operating fault
The programmed speed is cleared and
the dashes lash for a few seconds.
Consult a PEUGEOT dealer to have
the system checked.
Using the accelerator: -
exceed the memorised speed until
the speed required is reached,
- press the Set + or Set - button.
To memorise a speed lower than the
previous one:
- press the Set - button.
A brief press decreases the speed by
1 mph (km/h).
A maintained press decreases the
speed in steps of 5 mph (km/h). Cancelling the programmed
reference speed
When the vehicle becomes stationary,
after switching off the ignition, the
system no longer memorises a speed.
This table indicates the igures in
kilometres corresponding to the values
indicated in miles (which have been
rounded down) in the illustrations:
km/hmph
107 65
118 70

Page 49 of 194

Steering wheel controls
52
SPEED LIMITER "LIMIT"
"This is the selected speed which the
driver does not wish to exceed".
This selection is made with the engine
running while stationary or with the
vehicle moving. The minimum speed
which can be programmed is 20 mph
(30 km/h).
The speed of the vehicle responds
to the pressure of the driver’s foot as
far as the accelerator pedal point of
resistance which indicates that the
programmed speed has been reached.
However, pressing the pedal beyond
this point of resistance to the loor
permits exceeding of the programmed
speed.To resume use of the limiter, simply
reduce the pressure on the accelerator
pedal gradually and return to a speed
below that programmed.
If the vehicle is itted with a speed
limiter and cruise control (according
to the country in which the vehicle is
sold and the engine), these functions
cannot be activated at the same time.
The operating actions can be carried
out when stationary, with the engine
running, or with the vehicle moving. Function selected,
displaying of the
"Speed Limiter"
symbol.
Function deactivated,
last programmed
speed - OFF
(example at 65 mph
(107 km/h)).
Function activated
(example at 65 mph
(107 km/h)).
Vehicle speed above
(example at 70 mph
(118 km/h)), the
programmed speed is
displayed lashing.
Operating fault
detected, OFF - the
dashes lash.
This speed limiter shows the function
selection status on the instrument
panel and displays the programmed
speed:

Page 50 of 194

Steering wheel controls
ERGONOMICS and COMFORT
3
53
Selecting the function - Place the dial in the LIMIT position.
The limiter is selected but is not yet
active. The display indicates the
last programmed speed.
Programming a speed
A speed can be programmed without
activating the limiter but with the
engine running.
To memorise a speed higher than the
previous one:
- press the Set + button.
A brief press increases the speed by
1 mph (km/h).
A maintained press increases the
speed in steps of 5 mph (km/h). Activation/Deactivation (off)
Pressing this button once activates
the limiter, pressing the button again
deactivates it (OFF).
To memorise a speed lower than the
previous one:
- press the Set - button.
A brief press decreases the speed by
1 mph (km/h).
A maintained press decreases the
speed in steps of 5 mph (km/h).

Page 51 of 194

Steering wheel controls
54
Switching the function off - Place the dial in position 0 or switch
off the ignition to switch the system
off. The last programmed speed
remains in the memory.
Exceeding the programmed
speed
Pressing the accelerator pedal in order
to exceed the programmed speed
will have no effect unless you press
the pedal
irmly beyond the point of
resistance .
The limiter is deactivated temporarily
and the programmed speed lashes.
To return to the limiter function, reduce
your speed to below the programmed
speed. Operating fault
The programmed speed is cleared and
the dashes lash for a few seconds.
Contact a PEUGEOT dealer to have
the system checked.
Flashing of the speed
The speed lashes:
- following forcing of the accelerator point of resistance,
- when the limiter cannot prevent an increase in the vehicle speed due
to the proile of the road or on a
steep descent,
- in the event of sharp acceleration. Good practice
I
n any event, the speed limiter cannot
replace the need to observe speed limits,
nor can it replace the need for vigilance
and responsibility on the part of the driver.
Always pay attention to the proile of the
road and take care on sharp acceleration.
To avoid any jamming under the pedals:
- ensure that the mat is positioned correctly,
- never place one mat on top of another.
This table indicates the igures in
kilometres corresponding to the values
indicated in miles (which have been
rounded down) in the illustrations:
km/h mph
48 30
107 65
118 70

Page 106 of 194

2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
7
pqrs
0 #
ESC
MENU LIST
ESC
MENU LIST
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0
#
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0 #
1
2
3
4 5
62
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s
0 #
0606109TELEPHONE
CALLING A CONTACT
Turn the dial and select the DIAL
function.Press the PICK UP button to display
the superimposed telephone menu.
Press the dial to conirm the selection.
Dial the telephone number of your
contact using the alphanumeric
keypad. Press the PICK UP button to call the
number dialled.
Press the HANG UP button to end
the call.
ACCEPTING OR REFUSING A CALL Press the PICK UP button to accept
a call.
Press the HANG UP button to refuse
a call.
DIAL
Press the end of the steering wheel stalk for more
than 2 seconds to access the telephone menu:
calls log, directory, voice mailbox.

Page 110 of 194

08113
RADIO: selection of the previous stored station.
MP3/JUKEBOX: selection of the previous directory.
CD CHANGER: selection of the previous CD.
Selection of the previous item on a menu.
RADIO: selection of the next stored station.
MP3/JUKEBOX: selection of the next directory.
CD CHANGER: selection of the next CD.
Selection of the next item on a menu.RADIO: automatic search for a higher frequency.
CD/MP3/JUKEBOX/CD CHANGER: selection of the
next track.
CD/CD CHANGER: continuous press: fast forwards
play.
RADIO: automatic search for a lower frequency.
CD/MP3/JUKEBOX/CD CHANGER: selection of the
previous track.
CD/CD CHANGER: continuous press: fast backwards
play. - Change of sound source.
- Conirmation of a selection.
- Pick up/Hang up the telephone.
- Press for more than 2 seconds:
access to the telephone menu.
Volume increase.
Volume decrease.
CONTROL SHORT-CUTS
STEERING WHEEL CONTROLS
Mute: by pressing the volume
increase and decrease
buttons simultaneously.
The sound is restored by
pressing one of the two
volume buttons.

Page:   < prev 1-10 11-20 21-30 31-40 next >