ESP PEUGEOT 807 2008 Owners Manual

Instruments and controls
READY TO SET OFF
2
33
Warning light is indicates Solution - actionESP/ASR lashing. wheel skid avoided.
The system optimises drive and permits
improvement of the directional stability of the
vehicle. Chapter 5, "Driving safety" section.
remaining on.
system malfunction.
E.g.: under-inlation of the tyres.Check the pressure of the tyres.
Call a PEUGEOT dealer.
remaining on with
the button (below
the steering
wheel on the left)
pressed.
deactivation of the system. Operation of the system is deactivated.

Chapter 5, "Driving safety" section.
Diesel
pre-heating lit.climatic conditions requiring
pre-heating. Wait until the warning light is switched off before
operating the starter.
Dipped
headlamps/
Daytime lights litmanual selection or
automatic lighting.
Rotate the ring on the lights stalk to the second
position.
lighting of the dipped headlamps
from the time the ignition is switched
on - daytime lights. Depending on the
country in which the vehicle is sold.
Chapter 3, "Steering wheel controls" section.
Main beam
headlamps pulling of the stalk towards
you.
Pull the stalk to return to dipped headlamps.
and with an
audible signal,
ignition off. opening of the driver’s door
with the lights still on.
Rotate the ring on the lights stalk to position 0.
Direction
indicators lashing with
buzzer.change of direction via the
lights stalk, to the left of the
steering wheel. To the Right: control to be pushed upwards.

To the Left: control to be pushed downwards.

ERGONOMICS and COMFORT
3
61
Ventilation
6 - Adjustment of the air low
- Turn control knob 6 to
the right or to the left
respectively to increase or
decrease the air low.
On the display, the blades of the fan
darken when the air low is increased. 8 - Intake of exterior air/
Recirculation of interior
air
- Press this button to recirculate the air inside.
The air recirculation symbol and
indicator light 8 are displayed.
Recirculation insulates the passenger
compartment from outside smells and
smoke.
9 - Air conditioning On/Off
- Press this button to activate automatic
operation of the air
conditioning.
The symbol and the indicator light 9
are displayed.
- Press this button again to switch off the air conditioning.
The symbol and the indicator light 9
switch off. Avoid prolonged operation of
interior air recirculation (risk
of misting of the windows and
deterioration of air quality).
- Press this button again to return air intake to automatic control.
7 - Switching the system off -
Turn air low control knob 6 to the
left until the display switches off.
The action disarms all the system
functions, with the exception of
demisting of the rear screen. Your
comfort setting is no longer maintained
and switches off.
For your comfort, avoid remaining in
the off position.
- Operating control knob 6 again or
the "Visibility" button or "AUTO"
button reactivates the system with
the values which were present
before it was switched off.
Flashing of the points in the
temperature setting values indicates
that there is a malfunction of the air
conditioning.
Consult a PEUGEOT dealer.

106
1
SOURCE
2
S
O S SOURCE
MODE BAND TPT
A Y
DARKSOURCE
2
abc
5
jkl
8
tuv 3
def
6
mno
9
wxyz
1 4
ghi
7
pqrs
0 #
2
abc
5
jkl
8
tuv
3
def
6
mno
9
wxyz
1 4
ghi
r
7
pq s0 #
S
O S SOURCE
MODE BAND TPT
A Y
DARKSOURCESOURCE
ESC
MENU LIST
1
3
2Press the MENU button then select the CONFIGURATION
function,
then SOUNDS, then ACTIVATE AUXILIARY SOURCE to acti vate
the auxiliary input of the RT4 GPS audio/telephone.
Connect the portable equipment
(MP3 player…) to the audio sockets
(white and red, RCA type) located in the
glove box using a JACK/RCA
audio cable.
Press the SOURCE button several
times in succession and select AUX. Insert one or more CDs in the
changer.
Press the SOURCE button several
times in succession and select CD
CHANGER.
Press one of the buttons on the
alphanumeric keypad to select the
corresponding CD.
Press one of the buttons to select a
track on the CD.
The displaying and management of the commands takes place via
the portable equipment.
It is not possible to copy the iles onto the hard d isc from the auxiliary
input. It is not possible to copy the iles onto the hard d
isc from the CD
changer.
JACK/RCA AUDIO CABLE NOT SUPPLIED
USING THE AUXILIARY INPUT (AUX)
PLAYING A CD (NOT MP3 COMPATIBLE)
CD CHANGER

1
2
3
12
125
PLAYING A CD (NOT MP3 COMPATIBLE) Insert the CDs in the changer one by
one.
Press the SOURCE button several
times in succession and select CD
CHANGER.
Press one of the buttons on the
numeric keypad to select the
corresponding CD.
Press one of the buttons to select a
track on the CD.
Press and hold one of the buttons for
fast forwards or backwards play. Insert circular compact discs only.
Some anti-pirating systems, on original discs or CD
s
copied using a personal recorder, may cause faults
which are no relection on the quality of the origin al
player.
Without pressing the EJECT button, insert a CD in t he
player, play begins automatically.
To play a disc which has already been
inserted, press the SOURCE button
several times in succession and select
CD. Press one of the buttons to select a
track on the CD.
Press the LIST REFRESH button to
display the list of tracks on the CD.
CD CHANGER
PLAYING A CD
CD

1
2
31
2
5
1
04127HANDS-FREE KIT
For safety reasons and because they require prolong ed attention on
the part of the driver, the operations for matching of the Bluetooth
mobile telephone with the RD4 hands-free kit must b e carried out
with the vehicle stationary and the ignition on.
Select the accessory which corresponds to the
name of the vehicle, a superimposed coniguration
display appears on the multifunction display. Activate the telephone’s Bluetooth function and
carry out a search of the Bluetooth accessories
present for the telephone.
Select the YES tab on the display using
the buttons then conirm by pressing OK.
Enter the vehicle’s authentication code (=1234).
Depending on the telephone, you may be asked
to enter this code before the superimposed
coniguration display appears.
YES
YES
The services offered by the hands-free kit depend o
n the network, the SIM card and the
compatibility of the Bluetooth equipment used.
Consult your telephone’s manual and your operator t o ind out which services are
available to you. A list of mobile telephones which offer the best range of services is
available from the network. Consult a PEUGEOT deale r.
RECEIVING A CALL
An incoming call is announced by a ring and a super imposed display
on the multifunction display.
Select the YES tab on the display
using the buttons and conirm by
pressing OK.
Press the end of the steering
wheel stalk to accept the call.
Press the end of the steering wheel stalk for more
than two seconds to access your directory.
To dial a number, use the keypad on your
telephone. MAKING A CALL
DISPLAY C
MATCHING A TELEPHONE

SAFETY
139
Driving safety
5
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)
Activation of the ASR and ESP
systems
When the ignition is on, the ASR and
ESP systems are always active.Disarming the ASR/ESP systems
In certain conditions (vehicle stuck in
mud or snow, or on loose ground...), it
could prove useful to disarm the ASR
and ESP systems to make the wheels
spin and regain grip.
- Press the switch, situated under the
steering wheel on the right of the
fascia.
The indicator light comes on
accompanied by a message:
the ESP and ASR systems
no longer act on the engine
operation, but continue to act
on the brakes. Operating check
The ASR/ESP systems offer
increased safety during normal
driving, but should not incite the
driver to take risks or to drive at high
speed.
The operation of these systems is
ensured if the recommendations
of the manufacturer regarding
the wheels (tyres and rims), the
braking components, the electronic
components and the itting and repair
procedures within the PEUGEOT
network are observed.
After an impact, have the system
checked by a PEUGEOT dealer.
They engage again:
F
automatically above 30 mph
(50 km/h),
F manually by pressing the switch
again.
Operation of the ASR
and ESP systems
The warning light lashes if
the ASR or ESP is activated.
These systems are linked and
complement the ABS.
The ASR system optimises drive to
prevent the wheels skidding, by acting
on the brakes of the drive wheels
and on the engine. It also allows the
directional stability of the vehicle to be
improved on acceleration.
If there is a variation between the
trajectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the
engine and the brake of one or more
wheels, in order to put the vehicle back
on course, within the limits of the laws
of physics.
When a malfunction of the
systems occurs, the indicator
light comes on, accompanied
by an audible signal and a
message on the display.
Contact a PEUGEOT dealer to have
the system checked.

140
Driving safety
TYRE UNDER-INFLATION
DETECTION
Sensors check the tyre pressure during
driving, and trigger a warning in the
event of a malfunction (speed greater
than approx.15 mph [25 km/h]) or
puncture.
An outline representing one or more
wheels lashing indicates the location
of the wheel or wheels concerned.Flat tyre
The SERVICE warning light
comes on, accompanied
by the message "Tyre(s)
delated" , an outline on the display,
and an audible signal.
Check the tyre pressure as soon as
possible. If the damaged tyre is temporarily
stored in the boot, it will again emit
this message to remind you of the
necessity of having it repaired. This will
prevent another warning of the same
type being displayed.
Sensor(s)
not detected
The SERVICE warning light
comes on, accompanied
by the message "X tyre pressure
sensor(s) missing" , an outline on the
display and an audible signal.
Under-inlation detection is absent
from one (or several) tyre(s). Consult a
PEUGEOT dealer to replace the faulty
sensor(s). This message is also displayed
when one of the tyres is away
from the vehicle (being repaired)
or when a wheel without a sensor is
itted.
All repairs and changing of
tyres on a wheel itted with this
system must be carried out by a
PEUGEOT dealer.
The tyre under-inlation detection
system is a driving aid which does
not take the place of vigilance or the
responsibility of the driver.
This system does not remove the
need to have the tyre pressure
checked regularly (including the spare
wheel), to ensure that the dynamic
performance of the vehicle remains at
its best and to avoid premature wear
of the tyres, in particular in the case
of arduous driving (heavy load, high
speed).
The system may temporarily be
disturbed by radio broadcasts on a
frequency close to it.
Puncture
The STOP warning light
comes on, accompanied
by the message
"Punctured tyre(s)" , an outline on the
display and an audible signal.
Stop immediately, avoiding any sudden
movement of the steering wheel and
the brakes.
Change the damaged (punctured or
very delated) tyre, and have the tyre
pressure checked as soon as possible.
Refer to the "Changing a wheel"
section of chapter 8.

SAFETY
145
Airbags
5
Side air bags
If itted on your vehicle, this is a system
which protects the driver and front
passenger in the event of a serious
side impact in order to limit the risk of
injury to the chest.
Each side air bag is incorporated in the
front seat back frame, on the door side.The curtain air bag inlates between
the front or rear occupant of the vehicle
and the windows.
Impact detection zones
A. Front impact zone.
B. Side impact zone. In the event of a minor impact or
bump on the side of the vehicle or
if the vehicle rolls over, the air bag
may not be triggered.
The air bag is not triggered in the event
of a rear or front collision.
Operating fault
Curtain air bags
If itted on your vehicle, this is a
system which protects the driver and
passengers (with the exception of the
centre seats of rows 2 and 3) in the
event of a serious side impact in order
to limit the risk of head injuries.
Each curtain air bag is incorporated
in the pillars and the upper part of the
passenger compartment.
Activation
It is triggered unilaterally in the event
of a serious side impact applied to
all or part of the side impact zone
B
, perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane and directed from the outside
towards the inside of the vehicle.
The side air bag inlates between the
front occupant of the vehicle and the
corresponding door trim pad. Activation
It is triggered at the same time as
the corresponding side air bag in the
event of a serious side impact applied
to all or part of the side impact zone
B
, perpendicular to the longitudinal
centreline of the vehicle on a horizontal
plane and directed from the outside
towards the inside of the vehicle. If this warning light comes
on on the instrument panel,
accompanied by an audible
signal and a message on the
display, consult a PEUGEOT
dealer to have the system
checked. The air bags may no longer
be triggered in the event of a serious
impact.

166
Levels
CHECKS
To check the main levels
and certain components,
in accordance with the
manufacturer’s servicing schedule,
refer to the pages of the servicing
booklet which correspond to your
vehicle’s engine.
Only use products recommended
by PEUGEOT or products
of equivalent quality and
characteristics.
In order to optimise the operation
of units as important as the braking
circuit, PEUGEOT selects and offers
speciic products.
In order to avoid damaging the
electrical units, high pressure washing
to clean the engine compartment is
strictly prohibited.
Oil filter
Change the ilter regularly, in
accordance with the servicing
schedule. Refer to the "Under the bonnet"
section of chapter 7.
Particle emission filter (Diesel)
It is imperative that particle emission
ilter maintenance is carried out by a
PEUGEOT dealer.
On acceleration after the vehicle has
been running for a prolonged period
at very low speed or at idle, you may,
in exceptional circumstances, notice
the emission of water vapour at the
exhaust. This water vapour does not
have any adverse effect on vehicle
handling or the environment.
Battery
At the start of winter, have your battery
checked by a PEUGEOT dealer.
Brake pads
Brake pad wear depends on the style
of driving, in particular for vehicles
which are used in town, over short
distances. It may be necessary to
check the thickness of the pads, even
between services.
Unless there is a leak on the circuit, a
drop in the brake luid level indicates
that the brake pads are worn.
Brake disc/drum wear status
For any information relating to
checking the brake disc/drum wear
status, contact a PEUGEOT dealer.
Handbrake
Where the handbrake travel is too
great or there is a reduction in the
performance of the system, the
handbrake should be adjusted, even
between services.
Have the system checked by a
PEUGEOT dealer.
Carbon filter and passenger
compartment filter
The carbon ilter permits continuous
and effective iltering of dust.
If the passenger compartment ilter
becomes clogged, this may reduce
the performance of the air conditioning
system and generate unpleasant odours.
We recommend the use of a combined
passenger compartment ilter. By
means of its second special active
ilter, it contributes to the puriication
of the air breathed by the occupants
and to the cleanness of the passenger
compartment (reduction of allergic
symptoms, unpleasant odours and
greasy deposits).
Refer to the servicing booklet to ind
out the replacement interval for these
components.
Depending on the environment (dusty
atmosphere...) and the use of the
vehicle (urban driving...), change them
twice as often if necessary.
Manual gearbox
Have the level checked in accordance
with the manufacturer’s servicing
schedule.

172
Changing a bulb
CHANGING A BULB
1 - Dipped beam headlamps H7-55 W or xenon bulb. 3 - Fog lamps
H1-55 W.
WARNING: RISK OF
ELECTROCUTION
Xenon bulbs must be changed by a
PEUGEOT dealer.
Handle the bulbs with a dry cloth.
Make access easier on the right-
hand side by removing the wash-wipe
pipe and the fuse box cover. 4 - Side lights
W 5 W.
- Push the light from the inside towards the outside of the bumper.
- Pull the light forwards.
- Turn the bulb holder a quarter of a turn to the left and remove it.
- Turn the bulb a quarter of a turn to the left, remove it and change it.
When reitting, engage the light
towards the outside and move it
towards the inside of the bumper.
FRONT LIGHTS
1.
Dipped headlamps
2. Main beam headlamps
3. Fog lamps
4. Side lights
5. Direction indicators
2 - Main beam headlamps H7-55 W or xenon bulb. - Turn the protective cover
corresponding to the faulty bulb
a quarter of a turn to the left and
remove it.
- Disconnect the connector.
- Press the end of the securing clip to free it. Change the bulb.
When itting the new bulb, ensure that
the direction notches are positioned
correctly and the securing clip is ixed
properly.
- Reconnect the connector.
- Reit the protective cover, then turn it a quarter of a turn to the right.