tailgate PEUGEOT 807 2008 Owners Manual

135
4
7
1
FAMILIARISATION
Exterior
Audible and/or visual rear
parking assistance. Spare wheel
Raise the wheel to be
repaired by means of the
cable until it is l ush against
the l oor. Close the cover on
the access opening securely. 168 Transverse roof bars
Release the four levers,
move your bars then secure
the levers.
155
Tailgate
Locking and unlocking by
remote control.
Press the handle and raise
the tailgate.
168
Wheelbrace.
Jack box.
Towing eye.
8a 8b8b
2
4
8a
6
6
2
Parking assistance 26

>Visuel à venir
Accesses
26
Simultaneous locking or
unlocking of the tailgate
and the doors
The tailgate is locked or unlocked by
the remote control or the driver’s door
or passenger door lock.
To open, operate the handle C and lift
the tailgate. Tailgate release
Always remove the ignition key
when leaving the vehicle, even for
a short time. The tailgate locks automatically
when the vehicle is being driven
at more than 6 mph (10 km/h) and
unlocks when one of the front doors is
opened.
TAILGATE
ELECTRIC CHILD
SAFETY
This disarms all the electrical controls
in the rear:
- electric windows,
- sliding side doors,
- sunroofs in rows 2 and 3.
With the ignition on, press button B.
A message appears on the display,
accompanied by an audible signal.
"Tailgate open" warning
When the engine is running or the
vehicle is being driven, you are warned
if the tailgate is not closed correctly by
a diagram on the display, accompanied
by an audible signal.This enables the tailgate to be
unlocked in the event of a central
locking fault.
-
Fold back a row 2 rear seat,
- Fold back a row 3 rear seat or the
bench seat to gain access to the
lock from inside the boot,
- Insert a small screwdriver into hole
D in the lock and push it towards
the left to unlock the tailgate.

Steering wheel controls
48
Activation
Press the control downwards.
Activation of the function is
accompanied by a message on the
display.
The automatic windscreen wipers
function must be reactivated if the
ignition has been switched off for more
than one minute, by pressing the stalk
downwards.
Rear windscreen wiper
Turn the ring to the irst
notch. The wiping speed is
inversely proportional to the
speed of the vehicle.
Rear windscreen wash
Turn the ring past the irst
notch: the windscreen wash
then the windscreen wiper
operate for a ixed time. Good practice
When using an automatic car
wash, switch off the ignition without
setting the alarm.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic wiping.
In the event of a considerable amount
of snow or ice, switch on the rear
screen demister. Once de-icing is
complete, remove the snow or ice
which has accumulated on the rear
wiper blade. You can now operate the
rear windscreen wiper.
If a tailgate bicycle carrier
is used, deactivate the rear
wiper by going to the display’s
coniguration menu.
Deactivation/Switching off
Place the windscreen wipers stalk in
position
I, 1 or 2. Deactivation of the
function is accompanied by a message
on the display.
In the event of malfunction of the
automatic windscreen wipers, the
windscreen wipers will operate in
intermittent mode.
Contact a PEUGEOT dealer to have
the system checked. Automatic wiping - reverse gear
- place the front wipers stalk in a
position other than 0.
- engage reverse gear.
- the rear wiper operates with intermittent wiping.

72
Seats
REAR BENCH SEAT
From the boot, you can pull
on strap B and slide the seat
forwards to make it easier to load
the vehicle.
The rear bench seat must only be
itted in row 3. Seat back folded position
1.
Place the head restraints in the low
position.
2. Pull the strap C upwards, from the
tailgate. 3.
Tilt the seat back on the seat
cushion.
Vertical position of the bench seat
1. Place the head restraints in the low
position.
2. Pull the strap C upwards, from the
tailgate.
3. Fold the seat back onto the seat
cushion 4.
Pull the lever D to unlock the rear
anchorages.
5. Place the seat in the vertical
"folded" position.
When driving, attach the retaining
straps to the handles.
Forwards/backwards
adjustment
From the seat cushion, lift bar
A and
slide the seat towards the front or the
rear.

ERGONOMICS and COMFORT
3
81
Comfort and safety
REAR INTERIOR LAYOUT
5. Storage compartment11. Luggage retaining net "octopus"
position
Secure the net’s four hooks in their
stowing rings on the loor.
1. Access handle
2. Grab handle and coat hook
3. Door tray with storage for a can
and a bottle of water or for the
portable bin with ashtray
4. High load retaining net fastenings
Open the covers of the upper
fastenings in row 3.
Install the ends of the metal bar in
these fastenings.
Secure the two tray strap hooks in the
stowing rings on the loor.
Pull the two straps taut.
Secure the two hooks on the elastic
parts of the tray in these rings.
The rings are located directly below the
corresponding upper fastenings. 6. Can holder
7. Storage compartment
8. Bottle holder or portable bin with
ashtray
9. Luggage retaining net "hammock" position fastenings
Fold the net in two.
Secure the two centre hooks in the
stowing rings on the loor.
Secure the net’s remaining four hooks
on the tailgate pillars.
10.
12 V socket for accessories (120 W)
This permits the connection of a mobile
telephone charger, a baby’s bottle
warmer, ... 12. Load space cover
(5 seat version)
To install it:
- position one end of the roller in row 2,
- compress the opposite end of the roller and position it,
- release it to allow it to engage,
- unroll the cover as far as the pillars,
- secure the two hooks on the pillars,
To remove it:
- pull the cover towards you to detach it from its fastenings,
- return the cover into its roller,
- compress it and remove it from its support in row 2.
13. Rear shelf with umbrella holder (6-7-8 seat version)
To remove the shelf:
- pull it rearward,
- lift it slightly, then remove it.
To install it:
- tilt it forwards slightly,
- push to engage it in its fastenings.

154
Towing a trailer
On the contrary, use a high gear to
lower the engine speed and reduce
your speed.
In all cases, pay attention to the
coolant temperature. Brakes:
towing increases the braking
distance. Drive at a moderate speed,
change down early and brake
gradually. Please contact a PEUGEOT dealer
irst for further information.
Automatic adjustment
For vehicles with Xenon bulbs, this
system automatically corrects the
height of the beam, whatever the
load of the vehicle. The driver is then
assured of having optimum lighting and
not causing a nuisance to other road
users.
In certain cases of particularly
arduous use (towing the
maximum load up a steep slope
in high temperatures), the engine
automatically limits its power.
In this case, cutting off the air
conditioning allows the engine power
to be recovered, and therefore the
towing speed to be signiicantly
increased (approximately 12 mph
[20 km/h] more). Sequential control
of the gearbox may also become
unavailable. Lighting
Bicycle carrier If you it a bicycle carrier on
the tailgate, deactivate the
rear wiper from the display’s
coniguration menu.
Refer to the "Identiication
features" section of chapter 9. Refer to the "Steering wheel
controls" section of chapter 3.
When using a trailer connection,
you must add a fuse. Refer to
the "Changing a fuse" section of
chapter 8.
If the coolant temperature warning light
comes on, stop the vehicle and switch
off the engine as soon as possible.
Tyres: check the tyre pressures of
the towing vehicle and of the trailer,
observing the recommended pressure. Side wind:
sensitivity to side wind is
increased. Drive smoothly and at a
moderate speed.
Towbar
We recommend the use of original
PEUGEOT towbars, which have been
tested for endurance from the design
stage of your vehicle.
Towing equipment must be itted in
accordance with the manufacturer’s
instructions, with particular attention to
the towing capacities of your vehicle,
the load towed, the nose weight and
the electrical connection. As this itting
should be carried out by a professional,
we recommend that you entrust the
itting of this equipment to a PEUGEOT
dealer.
In accordance with the general
instructions referred to above, we draw
your attention to the risk connected
with itting a towbar or other electrical
accessory which is not recommended
by the PEUGEOT network. Fitting such
equipment could result in a failure of
your vehicle’s electronic system. Manual adjustment
Adjust your headlamps so as not to
dazzle other road users. Check the
electrical signalling of the trailer.

157
Other accessories
ACCESSORIES
6
OTHER ACCESSORIES
These accessories and parts, after
being tested and approved for
reliability and safety, are all adapted to
your 807. A wide choice of accessories
recommended by PEUGEOT and
original parts is available from
"PEUGEOT Accessories", the
catalogue and on line at PEUGEOT
dealers.To avoid any jamming under the
pedals:
- ensure that the mat is positioned correctly,
- never place one mat on top of another.
Compatible portable
equipment
For the RD4, the itting of an RCA
auxiliary socket is offered speciically
by the Network.
The audio cable for connection to
the auxiliary socket (RCA yellow-red
located in the glove box) is also offered
by the Network.
Following connection of the cable
and selection of the AUX mode, via
the source button, your portable
equipment is ready to operate.
Set the portable equipment to half
volume to avoid saturating the audio
system sound. Then use the audio
system volume button.
"Protection":
anti-theft
alarm, window engraving,
irst aid kit, safety jacket, rear
parking assistance, warning
triangle, ... "In-Car Technology":

audio systems, telephone,
hands-free kit, speakers, CD
changer, navigation system,
DVD player, ...
"Styling": alloy wheels,
trims, aluminium interior trim
kit, mud laps, ...
"Touring":
seat covers
compatible with side air bags,
mats, boot tray, sunroof,
luggage net, door delectors,
cool box secured on the
slides, clip armrest, load
carrying roof bars, roof box,
snow chains, ski carrier, tailgate bicycle
carrier, interior bicycle carrier, booster
seats and child seats, Isoix seats, side
sun blinds and rear blind, ...
Trailer towbar which must be itted by a
PEUGEOT dealer. The itting of electrical equipment
or accessories which are not
recommended by PEUGEOT
may result in a failure of your vehicle’s
electronic system.
Please note this speciic warning. You
are advised to contact a representative
of the Marque to be shown the range
of recommended equipment or
accessories.
Depending on the country in which
the vehicle is sold, it is compulsory to
have a safety jacket, warning triangle
and replacement bulbs available in the
vehicle. "Universal":
screenwash,
interior and exterior
maintenance and cleaning
products, replacement bulbs, ...
When using a tailgate bicycle
carrier, deactivate the rear
wiper from the display
coniguration menu.
Before installing a
radiocommunication transmitter with
aerial, contact a PEUGEOT dealer who
will inform you of the speciications of
the transmitters which can be itted,
in accordance with the Motor Vehicle
Electromagnetic Compatibility Directive
(2004/104/EC).
PEUGEOT Accessories
A further range is also available from
PEUGEOT Accessories, structured
around 5 categories:

173
TROUBLESHOOTING
8
Changing a bulb
Rear lights
1. Direction indicators
PY 21 W (amber).
2. Brake/side lights
P 21/5 W.
3. Reversing lights
P 21 W.
4. Fog lamps
P 21 W.
5 - Direction indicators
PY 21 W (amber).
- Turn the bulb holder a quarter of a
turn to the left and remove it.
- Change the bulb.
The headlamps are itted with
polycarbonate glass with a
protective coating. Do not clean
them with a dry or abrasive cloth, nor
with a detergent or solvent product.
Use a sponge and soapy water.
In certain climatic conditions (low
temperature, humidity), condensation
inside the headlamp glass is normal;
it disappears a few minutes after the
lights are switched on. Direction indicator side repeaters
WY 5 W (amber).
- Push the repeater rearwards and
release it from the mirror.
- Hold the connector and turn the bulb holder a quarter of a turn to
the left.
- Turn the bulb a quarter of a turn to the left, remove it and change it.
When reitting, engage the repeater
towards the rear and move it towards
the front of the mirror.
Amber coloured bulbs (direction
indicators and side repeaters)
must be changed for bulbs of
identical speciication and colour. These 4 bulbs are changed from inside
the vehicle:
- open the tailgate,
- remove the air extraction grille on
the side concerned,
- unclip the light harness,

173
TROUBLESHOOTING
8
Changing a bulb
Rear lights
1. Direction indicators
PY 21 W (amber).
2. Brake/side lights
P 21/5 W.
3. Reversing lights
P 21 W.
4. Fog lamps
P 21 W.
5 - Direction indicators
PY 21 W (amber).
- Turn the bulb holder a quarter of a
turn to the left and remove it.
- Change the bulb.
The headlamps are itted with
polycarbonate glass with a
protective coating. Do not clean
them with a dry or abrasive cloth, nor
with a detergent or solvent product.
Use a sponge and soapy water.
In certain climatic conditions (low
temperature, humidity), condensation
inside the headlamp glass is normal;
it disappears a few minutes after the
lights are switched on. Direction indicator side repeaters
WY 5 W (amber).
- Push the repeater rearwards and
release it from the mirror.
- Hold the connector and turn the bulb holder a quarter of a turn to
the left.
- Turn the bulb a quarter of a turn to the left, remove it and change it.
When reitting, engage the repeater
towards the rear and move it towards
the front of the mirror.
Amber coloured bulbs (direction
indicators and side repeaters)
must be changed for bulbs of
identical speciication and colour. These 4 bulbs are changed from inside
the vehicle:
- open the tailgate,
- remove the air extraction grille on
the side concerned,
- unclip the light harness,

174
Changing a bulb
NUMBER PLATE LIGHTS
W 5 W.
- Remove the lens.
- Change the faulty bulb.
THIRD BRAKE LIGHT
5 W 5 W bulbs.
- Remove the tailgate upper trim by unclipping it on each side.
- Squeeze the two tabs 1 to release
the bulb holder.
- Change the faulty bulb.
- When reitting, ensure that the tailgate upper trim has been put
back in place correctly.
- unscrew the two interior nuts and
remove the light,
- unscrew the bulb holder concerned an eighth of a turn to the left and
remove it,
- unscrew the faulty bulb an eighth of a turn to the left and change it.
When two or more bulbs are
faulty, you must replace them
immediately.
When reitting:
- take care to position the bulb
correctly and press on it to engage it,
- take care to position the bulb holder correctly and screw it in an eighth
of a turn to the right,
- take care to position and secure the light correctly.