Peugeot 807 Dag 2007.5 Service Manual

Steering wheel controls
42Activation
Press the control downwards. Activation of
the function is accompanied by a message
on the display.
The automatic windscreen wipers
function must be reactivated if the ignition
has been switched off for more than one
minute, by pressing the stalk downwards.
Deactivation/Switching off
Place the windscreen wipers stalk in position
I , 1 or 2. Deactivation of the function is
accompanied by a message on the display.
In the event of malfunction of the automatic
windscreen wipers, the windscreen wipers will
operate in intermittent mode.
Contact a PEUGEOT dealer to have the
system checked. Rear windscreen wiper
Turn the ring
to the first notch.
The wiping speed is inversely
proportional to the speed of the
vehicle.
Automatic wiping - reverse gear
 place the front wipers stalk in a position
other than 0.
 engage reverse gear.
 the rear wiper operates with intermittent
wiping.
Rear windscreen wash
Turn the ring past the first notch:
the windscreen wash then the
windscreen wiper operate for a
fixed time.
Good practice
When using an automatic car wash,
switch off the ignition without setting the
alarm.
In winter, it is advisable to wait until the
windscreen is completely clear of ice before
activating the automatic wiping.
In the event of a considerable amount of
snow or ice, switch on the rear screen
demister. Once de-icing is complete, remove
the snow or ice which has accumulated on
the rear wiper blade. You can now operate
the rear windscreen wiper.
If a tailgate bicycle carrier is used,
deactivate the rear wiper by going
to the display's configuration
menu.

ERGONOMICS and COMFORT43
3
CRUISE CONTROL "CRUISE"
"This is the speed at which the driver wishes
to drive".
This aid to driving in free-flowing traffic
enables the vehicle to maintain the speed
programmed by the driver, unless a steep
gradient makes this impossible.
In order for it to be programmed or
activated, the vehicle speed must be greater
than 25 mph (40 km/h) with at least 4th gear
engaged in the case of vehicles fitted with a
manual gearbox.On vehicles fitted with an automatic
gearbox, the lever must be in position

D (Drive) or at least 2nd gear must be
engaged in manual mode.
If the vehicle is fitted with a speed limiter
and cruise control (according to the country
in which the vehicle is sold and the engine),
these functions cannot be activated at the
same time. Function selected,
displaying of the "Cruise
Control" symbol.
Function deactivated,
OFF (example at 65 mph
(107 km/h)).
Function activated
(example at 65 mph
(107 km/h)).
Vehicle speed above (e.g.
70 mph (118 km/h)), the
programmed speed is
displayed flashing.
Operating fault detected,
OFF - the dashes flash.
This cruise control shows the function
selection status on the instrument panel and
displays the programmed speed:
Steering wheel controls

Steering wheel controls
44
Selecting the function
 Place the switch in the CRUISE position.
The cruise control is selected but is
not yet active and no speed has been
programmed.
First activation/
programming a
speed
 Reach the chosen
speed by pressing the
accelerator.
 Press the SET - or
SET + button.
This programmes/activates the reference
speed and the vehicle will maintain this
speed. Temporary exceeding of the speed
It is possible to
accelerate and drive
momentarily at a speed greater than the
programmed speed. The value programmed
flashes.
When the accelerator pedal is released, the
vehicle will return to the programmed speed. Reactivation

Following deactivation of the cruise
control, press this button.
Your vehicle will return to the last
programmed speed.
Alternatively, you can repeat the "first
activation" procedure.
Deactivation (off)
 Press this button or the
brake or clutch pedal.

ERGONOMICS and COMFORT45
3
Switching the function off

Place the dial in position 0 or switch off
the ignition to switch everything off.
Cancelling the programmed
reference speed
When the vehicle becomes stationary, after
switching off the ignition, the system no
longer memorises a speed.
Good practice
When changing the programmed
reference speed by means of a maintained
press, pay attention as the speed can
increase or decrease rapidly.
Do not use the cruise control on slippery
roads or in heavy traffic.
In the event of a steep slope, the cruise
control cannot prevent the vehicle from
exceeding the programmed speed.
In any event, the cruise control cannot
replace the need to observe the speed
limits, nor can it replace the need for
vigilance and responsibility on the part of the
driver.
To avoid any jamming under the pedals:
- ensure that the mat is positioned correctly,
- never place one mat on top of another.
Changing the
programmed speed
There are two methods of
memorising a speed higher
than the previous one:
Without using the
accelerator:
 press the Set + button.
A brief press increases the speed by 1 mph
(km/h).
A maintained press increases the speed in
steps of 5 mph (km/h).
Using the accelerator:
 exceed the memorised speed until the
speed required is reached,
 press the Set + or Set - button.
To memorise a speed lower than the
previous one:
 press the Set - button.
A brief press decreases the speed by 1 mph
(km/h).
A maintained press decreases the speed in
steps of 5 mph (km/h). Operating fault
The programmed speed is cleared and the
dashes flash for a few seconds.
Contact a PEUGEOT dealer to have the
system checked. Steering wheel controls

Steering wheel controls
46
SPEED LIMITER "LIMIT"
"This is the selected speed which the driver
does not wish to exceed".
This selection is made with the engine
running while stationary or with the vehicle
moving. The minimum speed which can be
programmed is 20 mph (30 km/h).
The speed of the vehicle responds to the
pressure of the driver's foot as far as the
accelerator pedal point of resistance which
indicates that the programmed speed has
been reached.
However, pressing the pedal beyond this
point of resistance to the floor permits
exceeding of the programmed speed. To resume use of the limiter, simply reduce
the pressure on the accelerator pedal
gradually and return to a speed below that
programmed.
If the vehicle is fitted with a speed limiter
and cruise control (according to the country
in which the vehicle is sold and the engine),
these functions cannot be activated at the
same time.
The operating actions can be carried out
when stationary, with the engine running,
or with the vehicle moving. Function selected,
displaying of the "Speed
Limiter" symbol.
Function deactivated, last
programmed speed - OFF
(example at 65 mph
(107 km/h)).
Function activated
(example at 65 mph
(107 km/h)).
Vehicle speed above
(example at 70 mph
(118 km/h)), the
programmed speed is
displayed flashing.
Operating fault detected,
OFF - the dashes flash.
This speed limiter shows the function
selection status on the instrument panel and
displays the programmed speed:

ERGONOMICS and COMFORT47
3
Selecting the function

Place the dial in the LIMIT position.
The limiter is selected but is not yet
active. The display indicates the last
programmed speed.
Programming a speed
A speed can be programmed without
activating the limiter but with the engine
running.
To memorise a speed higher than the
previous one:
 press the Set + button.
A brief press increases the speed by 1 mph (km/h).
A maintained press increases the speed in
steps of 5 mph (km/h).
To memorise a speed lower than the
previous one:
 press the Set - button.
A brief press decreases the speed by 1 mph (km/h).
A maintained press decreases the speed in
steps of 5 mph (km/h). Activation/Deactivation (off)
Pressing this button once activates the
limiter, pressing the button again deactivates
it (OFF).Steering wheel controls

Steering wheel controls
48
Switching the function off
 Place the dial in position 0 or switch off
the ignition to switch the system off. The
last programmed speed remains in the
memory.
Exceeding the programmed speed
Pressing the accelerator pedal in order to
exceed the programmed speed will have
no effect unless you press the pedal
firmly
beyond the point of resistance .
The limiter is deactivated temporarily and the
programmed speed flashes.
To return to the limiter function, reduce your
speed to below the programmed speed.
Flashing of the speed
The speed flashes:
- following forcing of the accelerator point of resistance,
- when the limiter cannot prevent an increase in the vehicle speed due to the
profile of the road or on a steep descent,
- in the event of sharp acceleration.
Good practice
In any event, the speed limiter cannot
replace the need to observe speed limits,
nor can it replace the need for vigilance and
responsibility on the part of the driver.
Always pay attention to the profile of the
road and take care on sharp acceleration.
To avoid any jamming under the pedals:
- ensure that the mat is positioned correctly,
- never place one mat on top of another.
Operating fault
The programmed speed is cleared and the
dashes flash for a few seconds.
Contact a PEUGEOT dealer to have the
system checked.

ERGONOMICS and COMFORT49
3
VENTILATION
CORRECT USE OF THE AIR
CONDITIONING
In all seasons, if fitted on your vehicle, the
air conditioning should only be used with
the windows closed. However, if the interior
temperature remains high after a prolonged
period parked in the sun, do not hesitate to
ventilate the passenger compartment for a
few minutes.
Good practice
If your vehicle is fitted with automatic
air conditioning, use the AUTO mode
as much as possible as it permits
optimised control of all of the functions :
air flow, passenger compartment comfort
temperature, air distribution, air intake
mode or air recirculation in the passenger
compartment.
Operate the air conditioning system for 5 to
10 minutes, once or twice a month, to keep
it in perfect working order.
It is normal that the condensation created by
the air conditioning system results in a flow
of water which may form a puddle under the
vehicle when parked.
If the system does not produce cold air,
do not use it and contact your PEUGEOT
dealer.
Passenger compartment filter,
carbon filter
Ensure that this filter is in good condition and
have all of the filter elements replaced regularly.
Refer to the "Checks" section of
chapter 7.
VENTS
"Leave them open"
For optimum distribution and diffusion of hot
or cool air in the passenger compartment,
there are adjustable central and side vents
which can be directed sideways (right or
left) towards the top of the body. For your
comfort while driving, do not close them,
direct the flow of air towards the windows
instead.
The air vents directed towards the floor of
the vehicle complete the equipment. Ventilation

50
De-icing the rear screen
and mirrorsDemisting, visibility programme
DE-ICING AND DEMISTING
The comfort programme may not
be sufficient to quickly demist or
de-ice the windows (humidity,
several passengers, ice).
In this case, select the visibility
programme. The visibility programme
indicator light comes on.
It activates the air conditioning, the air flow,
the de-icing of the rear screen and provides
optimum distribution of the ventilation to the
windscreen and side windows.
It deactivates the air recirculation.
Press this button, with the engine
running, to de-ice the rear screen
and mirrors.
The de-icing indicator light comes
on. The duration of de-icing depends on the
exterior temperature.
Pressing the button again reactivates the
de-icing.
It is possible to stop the de-icing before
it is switched off automatically by
pressing this button again.
Ventilation

ERGONOMICS and COMFORT51
3
the side vents and the central
vents,
MANUAL
Located on the centre console, the control
panel is to the right of the gear lever.
1 - Setting the air distribution
Turn control knob
1 to the corresponding
position to direct the flow of air towards: the side vents, the central vents
and the footwells, the footwells,
the windscreen and the footwells,
the windscreen.
2 - Temperature adjustment
Position control knob
2 to suit
your requirements: from blue (cold
when the air conditioning is on) to
red (hot).
To lower the temperature inside the
passenger compartment quickly, position
control knob 2 on "MAX" .
The air conditioning 5 and the air
recirculation 4 come on.
Turn the knob away from the "MAX"
position when the ambient air suits your
requirements.
The air conditioning 5 remains on while the
air recirculation 4 switches off. Ventilation